WIND TUNNEL INVESTIGATION OF AN ASPECT RATIO 10 TANDEM WING AIRCRAFT CONFIGURATION IN GROUND EFFECT. PART I. LONGITUDINAL CHARACTERISTICS

1966 ◽  
Author(s):  
Charles W. Harry ◽  
Lynn A. Trobaugh
Keyword(s):  
Wind Tunnel ◽  
Aspect Ratio ◽  
Ground Effect

WIND-TUNNEL INVESTIGATION OF SINGLE AND TANDEM LOW-ASPECT-RATIO WINGS IN GROUND EFFECT

1964 ◽  
Author(s):  
William D. Hinshaw ◽  
William E. Sickles ◽  
John R. Brown ◽  
William P. Stevens ◽  
Samuel G. Hansen
Keyword(s):  
Wind Tunnel ◽  
Aspect Ratio ◽  
Ground Effect ◽  
Low Aspect Ratio ◽  
Low Aspect Ratio Wings

Aerodynamic interference test of quad tilt rotor aircraft in wind tunnel

2019 ◽  
Vol 233 (15) ◽  
pp. 5553-5566 ◽  
Author(s):  
Kun Chen ◽  
Zhiwei Shi ◽  
Shengxiang Tong ◽  
Yizhang Dong ◽  
Jie Chen
Keyword(s):  
Wind Tunnel ◽  
Reference Value ◽  
Ground Effect ◽  
Open Loop ◽  
Force Balance ◽  
Scale Model ◽  
Operating Condition ◽  
Tilt Rotor ◽  
Interference Test ◽  
Aerodynamic Interference

There is an obvious aerodynamic interference problem that occurs for a quad tilt rotor in near-ground hovering or in the conversion operating condition. This paper presents an aerodynamic interference test of the quad tilt rotor in a wind tunnel. A 1:35 scale model of the quad tilt rotor is used in this test. To substitute for the ground, a moveable platform is designed in a low-speed open-loop wind tunnel to simulate different flight altitudes of the quad tilt rotor in hovering or forward flight. A rod six-component force balance is used to measure the loads on the aircraft, and the flow field below the airframe is captured using particle image velocimetry. The experimental results show that the ground effect is significant when the hover height above the ground is less than the rotor diameter of the quad tilt rotor aircraft, and the maximum upload of the airframe is approximately 12% of the total vertical thrust with the appearance of obvious fountain flow. During the conversion operating condition, the upload of the airframe is reduced compared with that in the hovering state, which is affected by rotor wake and incoming flow. The aerodynamic interference test results of the quad tilt rotor aircraft have important reference value in power system selection, control system design, and carrying capacity improvement with the advantage of ground effect.

Power Augmentation of a HAWT by Mie-type Tip Vanes, considering Wind Tunnel Flow Visualisation, Blade-Aspect Ratios and Reynolds Number

2003 ◽  
Vol 27 (3) ◽  
pp. 183-194 ◽  
Author(s):  
Yukimaru Shimizu ◽  
Edmond Ismaili ◽  
Yasunari Kamada ◽  
Takao Maeda
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Aspect Ratio ◽  
Reynolds Numbers ◽  
Flow Visualisation ◽  
Velocity Measurements ◽  
Horizontal Axis Wind Turbine ◽  
Aspect Ratios ◽  
Detailed Surface ◽  
Blade Tips

Wind tunnel results are reported concerning the effects of blade aspect ratio and Reynolds number on the performance of a horizontal axis wind turbine (HAWT) with Mie-type1 tip attachments. The flow behaviour around the blade tips and the Mie-type tip vanes is presented. Detailed surface oil film visualization and velocity measurements around the blade tips, with and without Mie vanes, were obtained with the two-dimensional, Laser-Doppler Velocimetry method. Experiments were performed with rotors having blades with different aspect ratio and operating at different Reynolds numbers. The properties of the vortices generated by the Mie vanes and the blade tips were carefully studied. It was found that increased power augmentation by Mie vanes is achieved with blades having smaller aspect ratio and smaller Reynolds number.

The development of the winged keel for twelve-metre yachts

1986 ◽  
Vol 173 ◽  
pp. 55-71 ◽  
Author(s):  
P. Van Oossanen ◽  
P. N. Joubert
Keyword(s):  
Wind Tunnel ◽  
Aspect Ratio ◽  
Experimental Analysis ◽  
Design Parameters ◽  
Low Aspect Ratio ◽  
Lifting Surface ◽  
Wind Tunnel Measurements ◽  
America’S Cup

In this paper the authors present a numerical and experimental analysis of the winged keel originally developed for the International twelve-metre class yacht Australia II that won the America's Cup in 1983. After briefly explaining why this keel was evolved in 1981, some basic considerations are presented relating keel performance to various design parameters. The results of numerical flow analyses and wind-tunnel measurements on a model of a winged keel are then presented and compared. The differences between the performance with and without winglets fitted to the keel are discussed. The fitting of winglets appreciably enhances the performance of a low-aspect-ratio lifting surface such as the keel of a twelve-metre yacht.

Wind Tunnel Testing and Computational Fluid Dynamics Analysis of a Wing-in-Ground Effect Vehicle

2007 ◽  
Author(s):  
Boonseng Soh ◽  
Andrew Low ◽  
Cees Bil ◽  
Brendon Bobbermien
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Tunnel ◽  
Ground Effect ◽  
Wind Tunnel Testing ◽  
Cfd Modelling ◽  
Aerodynamic Analysis ◽  
Computational Fluid Dynamics Analysis ◽  
Wing In Ground Effect ◽  
Tunnel Testing

The Wing-in-Ground Effect Concept Technology Demonstrator (WIGE CTD) project is a joint venture between Advanced Aerosystem Technologies Pty Ltd and RMIT University, aiming to design, validate and build a prototype recreational vehicle to fly two passengers over a distance of 500km at approximately 120km/h. The WIGE vehicle will fly very close to the surface, usually water, taking advantage of ground effect to transport passengers with a greater lift/drag ratio, and thus greater fuel-efficiency than conventional aircraft. Following preliminary design, an aerodynamic analysis of the vehicle was performed using wind tunnel testing and Computational Fluid Dynamics (CFD). This paper describes the methods used for wind tunnel testing and CFD modelling of the WIGE CTD design. Results obtained using the two approaches are compared with the aim of validating the CFD model and the techniques used in both wind tunnel and CFD modelling for use in future analyses. In addition to the aerodynamic analysis, a basic CFD prediction of the maximum hydrodynamic drag experienced during take off was attempted using a simple model of the WIGE vehicle hull. This result is required in order to ensure that the aquatic take off required by WIGE vehicles was possible for the design. Concurrently, the feasibility of using a general-purpose CFD solver like Fluent to analyse hull performance was also evaluated through this aspect of the investigation.

Sign in / Sign up

Export Citation Format

Share Document