TENSILE AND CREEP-RUPTURE PROPERTIES OF DISILICIDE-COATED UNALLOYED MOLYBDENUM SHEET AT 2800, 3000, AND 3200 F

1963 ◽  
Author(s):  
A. S. Rabensteine
Keyword(s):  
Creep Rupture ◽  
Molybdenum Sheet ◽  
Rupture Properties

WISCALLOY 25-35Nb

Alloy Digest ◽  
1996 ◽  
Vol 45 (9) ◽  
Keyword(s):  
Stainless Steel ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Creep Rupture ◽  
Centrifugally Cast ◽  
Heat Resistant ◽  
Rupture Properties

Abstract Wiscalloy 25-35Nb is a high-temperature cast heat-resistant stainless steel with good creep-rupture properties. The alloy is centrifugally cast and is often used as petrochemical furnace tubing. This datasheet provides information on composition, physical properties, and tensile properties as well as creep. It also includes information on casting and joining. Filing Code: SS-654. Producer or source: Wisconsin Centrifugal.

The role of precipitation parameters upon the creep rupture properties of inconel alloy X-750

1973 ◽  
Vol 11 (5) ◽  
pp. 255-268 ◽  
Author(s):  
P.K Venkiteswaran ◽  
M.W.A Bright ◽  
D.M.R Taplin
Keyword(s):  
Creep Rupture ◽  
Inconel Alloy ◽  
Rupture Properties

scholarly journals Creep rupture properties of bare and coated polycrystalline nickel-based superalloy Rene®80

2021 ◽  
pp. 36-36
Author(s):  
M.M. Barjesteh ◽  
S.M. Abbasi ◽  
K.Z. Madar ◽  
K. Shirvani
Keyword(s):  
Elevated Temperatures ◽  
Life Time ◽  
Creep Rupture ◽  
Polycrystalline Nickel ◽  
Creep Life ◽  
Nickel Based Superalloy ◽  
Platinum Aluminide ◽  
Rupture Properties ◽  
Low Activity ◽  
Rupture Behavior

Creep deformation is one of the life time limiting reasons for gas turbine parts that are subjected to stresses at elevated temperatures. In this study, creep rupture behavior of uncoated and platinum-aluminide coated Rene?80 has been determined at 760?C/657 MPa, 871?C/343 MPa and 982?C/190 Mpa in air. For this purpose, an initial layer of platinum with a thickness of 6?m was applied on the creep specimens. Subsequently, the aluminizing were formed in the conventional pack cementation method via the Low Temperature-High Activity (LTHA) and High Temperature-Low Activity (HTLA) processes. Results of creep-rupture tests showed a decrease in resistance to creep rupture of coated specimen, compared to the uncoated ones. The reductions in rupture lives in LTHA and HTLA methods at 760?C/657 MPa, 871?C/343 MPa and 982?C/190 MPa were almost (26% and 41.8%), (27.6% and 38.5%) and (22.4% and 40.3%), respectively as compared to the uncoated ones. However, the HTLA aluminizing method showed an intense reduction in creep life. Results of fractographic studies on coated and uncoated specimens indicated a combination of ductile and brittle failure mechanisms for all samples. Although, the base failure mode in substrate was grain boundary voids, cracks initiated from coating at 760?C/657MPa and 871?C/343. No cracking in the coating was observed at 982?C/190MPa.

Sign in / Sign up

Export Citation Format

Share Document