EFFECTS OF BOUNDARY CONDITIONS AND INITIAL OUT-OF-ROUNDNESS ON THE STRENGTH OF THIN-WALLED CYLINDERS SUBJECT TO EXTERNAL HYDROSTATIC PRESSURE

1957 ◽  
Author(s):  
G. D. GALLETLY ◽  
R. BART
Keyword(s):  
Hydrostatic Pressure ◽  
Boundary Conditions ◽  
External Hydrostatic Pressure ◽  
Thin Walled

Effects of Boundary Conditions and Initial Out-of-Roundness on the Strength of Thin-Walled Cylinders Subject to External Hydrostatic Pressure

1956 ◽  
Vol 23 (3) ◽  
pp. 351-358
Author(s):  
G. D. Galletly ◽  
R. Bart
Keyword(s):  
Hydrostatic Pressure ◽  
Boundary Conditions ◽  
Semiempirical Methods ◽  
Test Results ◽  
External Hydrostatic Pressure ◽  
Simply Supported ◽  
Small Deflection ◽  
The Difference ◽  
Deflection Theory ◽  
Theoretical Results

Abstract Using classical small-deflection theory, an investigation was made of the effects of boundary conditions and initial out-of-roundness on the strength of cylinders subject to external hydrostatic pressure. The equations developed in this paper for initially out-of-round cylinders with clamped ends, and a slightly modified form of the equations previously derived by Bodner and Berks for simply supported ends, were applied to some actual test results obtained from nine steel cylinders which had been subjected to external hydrostatic pressure. Three semiempirical methods for determining the initial out-of-roundness of the cylinders also were investigated and these are described in the paper. The investigation indicates that if the initial out-of-roundness is determined in a manner similar to that suggested by Holt then the correlation between the experimental and theoretical results is quite good. The investigation also indicates that while the difference in collapse pressures for clamped-end and simply supported perfect cylinders may be quite considerable, this does not appear to be the case when initial out-of-roundnesses of a practical magnitude are considered.

scholarly journals On the theory and practice of thin-walled structures

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Tamaz Vashakmadze
Keyword(s):  
Partial Differential Equations ◽  
Differential Equations ◽  
Boundary Conditions ◽  
Complex Analysis ◽  
Theory And Practice ◽  
Linear Case ◽  
Wide Sense ◽  
Partial Differential ◽  
Thin Walled Structures ◽  
Thin Walled

Abstract The basic problem of satisfaction of boundary conditions is considered when the generalized stress vector is given on the surfaces of elastic plates and shells. This problem has so far remained open for both refined theories in a wide sense and hierarchic type models. In the linear case, it was formulated by I. N. Vekua for hierarchic models. In the nonlinear case, bending and compression-expansion processes do not split and in this context the exact structure is presented for the system of differential equations of von Kármán–Mindlin–Reisner (KMR) type, constructed without using a variety of ad hoc assumptions since one of the two relations of this system in the classical form is the compatibility condition, but not the equilibrium equation. In this paper, a unity mathematical theory is elaborated in both linear and nonlinear cases for anisotropic inhomogeneous elastic thin-walled structures. The theory approximately satisfies the corresponding system of partial differential equations and the boundary conditions on the surfaces of such structures. The problem is investigated and solved for hierarchic models too. The obtained results broaden the sphere of applications of complex analysis methods. The classical theory of finding a general solution of partial differential equations of complex analysis, which in the linear case was thoroughly developed in the works of Goursat, Weyl, Walsh, Bergman, Kolosov, Muskhelishvili, Bers, Vekua and others, is extended to the solution of basic nonlinear differential equations containing the nonlinear summand, which is a composition of Laplace and Monge–Ampére operators.

The Bending, Buckling, and Flexural Vibration of Simply Supported Polygonal Plates by Point-Matching

1961 ◽  
Vol 28 (2) ◽  
pp. 288-291 ◽  
Author(s):  
H. D. Conway
Keyword(s):  
Hydrostatic Pressure ◽  
Boundary Conditions ◽  
Flexural Vibration ◽  
Frequency Equation ◽  
Numerical Results ◽  
Special Technique ◽  
Point Matching ◽  
Buckling Loads ◽  
Simply Supported ◽  
Flexural Vibrations

The bending by uniform lateral loading, buckling by two-dimensional hydrostatic pressure, and the flexural vibrations of simply supported polygonal plates are investigated. The method of meeting the boundary conditions at discrete points, together with the Marcus membrane analog [1], is found to be very advantageous. Numerical examples include the calculation of the deflections and moments, and buckling loads of triangular square, and hexagonal plates. A special technique is then given, whereby the boundary conditions are exactly satisfied along one edge, and an example of the buckling of an isosceles, right-angled triangle plate is analyzed. Finally, the frequency equation for the flexural vibrations of simply supported polygonal plates is shown to be the same as that for buckling under hydrostatic pressure, and numerical results can be written by analogy. All numerical results agree well with the exact solutions, where the latter are known.

Study of Ductile-to-Brittle Transition in Single Grit Diamond Scribing of Silicon: Application to Wire Sawing of Silicon Wafers

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Hao Wu ◽  
Shreyes N. Melkote
Keyword(s):  
Hydrostatic Pressure ◽  
Silicon Wafers ◽  
Depth Of Cut ◽  
Critical Depth ◽  
External Hydrostatic Pressure ◽  
Tensile Stresses ◽  
Brittle Transition ◽  
Ductile Mode Cutting ◽  
Critical Depth Of Cut ◽  
Ductile To Brittle Transition

The ductile-to-brittle cutting mode transition in single grit diamond scribing of monocrystalline silicon is investigated in this paper. Specifically, the effects of scriber tip geometry, coefficient of friction, and external hydrostatic pressure on the critical depth of cut associated with ductile-to-brittle transition and crack generation are studied via an eXtended Finite Element Method (XFEM) based model, which is experimentally validated. Scribers with a large tip radius are shown to produce lower tensile stresses and a larger critical depth of cut compared with scribers with a sharp tip. Spherical tipped scribers are shown to generate only surface cracks, while sharp tipped scribers (conical, Berkovich and Vickers) are found to create large subsurface tensile stresses, which can lead to nucleation of subsurface median/lateral cracks. Lowering the friction coefficient tends to increase the critical depth of cut and hence the extent of ductile mode cutting. The results also show that larger critical depth of cut can be obtained under external hydrostatic pressure. This knowledge is expected to be useful in optimizing the design and application of the diamond coated wire employed in fixed abrasive diamond wire sawing of photovoltaic silicon wafers.

scholarly journals Flexural-Torsional Vibration of Thin-Walled Beams Subjected to Combined Initial Axial Load and End Bending Moment: Application to the Design of Saw Tooth Blades

2019 ◽  
Vol 2019 ◽  
pp. 1-11
Author(s):  
Van Binh Phung ◽  
Anh Tuan Nguyen ◽  
Hoang Minh Dang ◽  
Thanh-Phong Dao ◽  
V. N. Duc
Keyword(s):  
Boundary Conditions ◽  
Axial Load ◽  
Stability Boundary ◽  
Bending Moment ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Rayleigh Method ◽  
Thin Walled ◽  
The Stability ◽  
Fixed End

The present paper analyzes the vibration issue of thin-walled beams under combined initial axial load and end moment in two cases with different boundary conditions, specifically the simply supported-end and the laterally fixed-end boundary conditions. The analytical expressions for the first natural frequencies of thin-walled beams were derived by two methods that are a method based on the existence of the roots theorem of differential equation systems and the Rayleigh method. In particular, the stability boundary of a beam can be determined directly from its first natural frequency expression. The analytical results are in good agreement with those from the finite element analysis software ANSYS Mechanical APDL. The research results obtained here are useful for those creating tooth blade designs of innovative frame saw machines.

scholarly journals Buckling Of The Stiffened Flange Of The Thin-Walled Member At Longitudinal Stress Variation

2015 ◽  
Vol 61 (3) ◽  
pp. 149-168
Author(s):  
A. Szychowski
Keyword(s):  
Boundary Conditions ◽  
Free Edge ◽  
Cantilever Plate ◽  
Longitudinal Stress ◽  
Stress Variation ◽  
Buckling Modes ◽  
Load Distributions ◽  
Edge Stiffener ◽  
Thin Walled ◽  
Elastically Restrained

AbstractBuckling of the stiffened flange of a thin-walled member is reduced to the buckling analysis of the cantilever plate, elastically restrained against rotation, with the free edge stiffener, which is susceptible to deflection. Longitudinal stress variation is taken into account using a linear function and a 2nd degree parabola. Deflection functions for the plate and the stiffener, adopted in the study, made it possible to model boundary conditions and different buckling modes at the occurrence of longitudinal stress variation. Graphs of buckling coefficients are determined for different load distributions as a function of the elastic restraint coefficient and geometric details of the stiffener. Exemplary buckling modes are presented.

Sign in / Sign up

Export Citation Format

Share Document