Combination of Dual-Energy Gamma Ray/Venturi Multiphase Flowmeter and Phase Splitter for Application in Very High Gas Volume Fraction Environment

2004 ◽  
Author(s):  
E. Delvaux ◽  
B. Germond ◽  
N.K. Jha
Keyword(s):  
Gamma Ray ◽  
Volume Fraction ◽  
Dual Energy ◽  
Energy Gamma ◽  
Gas Volume Fraction ◽  
Gas Volume ◽  
Very High ◽  
Phase Splitter

Multiple Application of Multi-Energy Gamma Ray Venture Type Multiphase Flowmeter in Giant Karachaganak Gas Condensate Field

2021 ◽  
Author(s):  
Aidyn Kartamyssov ◽  
Beibit Bissakayev ◽  
Bolat Zhumabayev ◽  
Raziya Shektebayeva ◽  
Miro Durekovic ◽  
...  
Keyword(s):  
Gamma Ray ◽  
Volume Fraction ◽  
Gas Condensate ◽  
Multiple Application ◽  
Energy Gamma ◽  
Gas Volume Fraction ◽  
Water Cut ◽  
Operational Range ◽  
Gas Volume

Abstract The objective of this paper is to demonstrate multiple application of multi-energy gamma ray venture type multiphase flowmeter (MPFM) trial campaign in Karachaganak gas condensate giant carbonate field, operated by KPO B.V. The results of MPFM that was included into surface well test spread, to verify its performance, was compared against portable test separator and plant production testing facilities (control separator, flowmeters) and manual sampling results. MPFM from other vendors historically failed to deliver accurate production measurement mainly due to complexity of reservoir fluid in Karachaganak field. To ensure the MPFM considers this complexity, PVT samples were taken to provide laboratory data for PVT model of the MPFM to ensure sufficient quality of PVT data and compare against PVT model inside MPFM. First application of MPFM was during clean-up of the well prior handover well to production. Using MPFM helped to improve the quality during data acquisition. This information was critical for the well to be accepted by processing facility it is hooked-up to and to define optimal operating regime. Validation of BS&W, GOR and rates in unstable (foaming, carry over) and transient phase of production using MPFM has shown practical advantages. Another application was for water sampling loops to measure water cut and production rates. KPO has had challenges with inaccurate water cut measurement due to the limitations of existing test separators. A recent approach of performing fluid sampling (sampling loop) at the well head proved to be reliable source of measurements. In addition, the MPFM in combination with the test separator has been used to further improve the quality of the measurements of each phase. The third MPFM application had been with high gas-volume-fraction (HGVF) pumps, that helped to produce from low reservoir pressure, low GOR and high water cut wells. The operational range of HGVF pump was limited to maximum 75-80% of gas-volume-fraction (GVF). MPFM measures GVF in real-time to ensure HGVF pump operates in optimum operational range by managing the surface flow conditions. With current limitations of test separators in Karachaganak field and due to complexity of the gas-condensate fluid, the use of MPFM brings additional quality in the measurements (rates, water cut and GOR) which is crucial for field production optimization, reservoir management and short and long term forecasting.

Model for calculating the gas volume fraction of a gas-cut wellbore through natural gamma-ray logging

2017 ◽  
Vol 151 ◽  
pp. 49-54 ◽  
Author(s):  
Hao Li ◽  
Jinbo Wang ◽  
Baojiang Sun ◽  
Zhiming Yin ◽  
Jinzhi Yao ◽  
...  
Keyword(s):  
Gamma Ray ◽  
Volume Fraction ◽  
Natural Gamma ◽  
Gas Volume Fraction ◽  
Gas Volume

scholarly journals Effect of the Gas Volume Fraction on the Pressure Load of the Multiphase Pump Blade

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 650
Author(s):  
Guangtai Shi ◽  
Dandan Yan ◽  
Xiaobing Liu ◽  
Yexiang Xiao ◽  
Zekui Shu
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Volume Fraction ◽  
Pump Impeller ◽  
Impeller Blade ◽  
Multiphase Pump ◽  
Pressure Load ◽  
Gas Volume Fraction ◽  
Power Capability ◽  
Gas Volume

The gas volume fraction (GVF) often changes from time to time in a multiphase pump, causing the power capability of the pump to be increasingly affected. In the purpose of revealing the pressure load characteristics of the multiphase pump impeller blade with the gas-liquid two-phase case, firstly, a numerical simulation which uses the SST k-ω turbulence model is verified with an experiment. Then, the computational fluid dynamics (CFD) software is employed to investigate the variation characteristics of static pressure and pressure load of the multiphase pump impeller blade under the diverse inlet gas volume fractions (IGVFs) and flow rates. The results show that the effect of IGVF on the head and hydraulic efficiency at a small flow rate is obviously less than that at design and large flow rates. The static pressure on the blade pressure side (PS) is scarcely affected by the IGVF. However, the IGVF has an evident effect on the static pressure on the impeller blade suction side (SS). Moreover, the pump power capability is descended by degrees as the IGVF increases, and it is also descended with the increase of the flow rate at the impeller inlet. Simultaneously, under the same IGVF, with the increase of the flow rate, the peak value of the pressure load begins to gradually move toward the outlet and its value from hub to shroud is increased. The research results have important theoretical significance for improving the power capability of the multiphase pump impeller.

scholarly journals A STRONG RADIO BRIGHTENING AT THE JET BASE OF M 87 DURING THE ELEVATED VERY HIGH ENERGY GAMMA-RAY STATE IN 2012

2014 ◽  
Vol 788 (2) ◽  
pp. 165 ◽  
Author(s):  
K. Hada ◽  
M. Giroletti ◽  
M. Kino ◽  
G. Giovannini ◽  
F. D'Ammando ◽  
...  
Keyword(s):  
Gamma Ray ◽  
High Energy ◽  
High Energy Gamma ◽  
Very High Energy ◽  
Energy Gamma ◽  
Very High

scholarly journals Thrust Enhancement Through Bubble Injection Into an Expanding-Contracting Nozzle With a Throat

2014 ◽  
Vol 136 (7) ◽  
Author(s):  
Sowmitra Singh ◽  
Tiffany Fourmeau ◽  
Jin-Keun Choi ◽  
Georges L. Chahine
Keyword(s):  
Volume Fraction ◽  
Bubbly Flow ◽  
Design Tool ◽  
Nozzle Geometry ◽  
Mixture Flow ◽  
Subsonic Flows ◽  
Choked Flow ◽  
Optimum Geometry ◽  
Gas Volume Fraction ◽  
Gas Volume

This paper addresses the concept of thrust augmentation through bubble injection into an expanding-contracting nozzle with a throat. The presence of a throat in an expanding-contracting nozzle can result in flow transition from the subsonic regime to the supersonic regime (choked conditions) for a bubbly mixture flow, which may result in a substantial increase in jet thrust. This increase would primarily arise from the fact that the injected gas bubbles expand drastically in the supersonic region of the flow. In the current work, an analytical 1D model is developed to capture choked bubbly flow in an expanding-contracting nozzle with a throat. The study provides analytical and numerical support to analytical observations and serves as a design tool for nozzle geometries that can achieve efficient choked bubbly flows through nozzles. Starting from the 1D mixture continuity and momentum equations, along with an equation of state for the bubbly mixture, expressions for mixture velocity and gas volume fraction were derived. Starting with a fixed geometry and an imposed upstream pressure for a choked flow in the nozzle, the derived expressions were iteratively solved to obtain the exit pressures and velocities for different injected gas volume fractions. The variation of thrust enhancement with the injected gas volume fraction was also studied. Additionally, the geometric parameters were varied (area of the exit, area of the throat) to understand the influence of the nozzle geometry on the thrust enhancement and on the flow conditions at the inlet. This parametric study provides a performance map that can be used to design a bubble augmented waterjet propulsor, which can achieve and exploit supersonic flow. It was found that the optimum geometry for choked flows, unlike the optimum geometry under purely subsonic flows, had a dependence on the injected gas volume fraction. Furthermore, for the same injected gas volume fraction the optimum geometry for choked flows resulted in greater thrust enhancement compared to the optimum geometry for purely subsonic flows.

Sign in / Sign up

Export Citation Format

Share Document