Containment of Massive Hydraulic Fractures

1978 ◽  
Vol 18 (01) ◽  
pp. 27-32 ◽  
Author(s):  
E.R. Simonson ◽  
A.S. Abou-Sayed ◽  
R.J. Clifton
Keyword(s):  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Fracture Propagation ◽  
Rocky Mountain ◽  
In Situ Stress ◽  
Hydraulic Fractures ◽  
Pressure Gradients ◽  
In Situ Stresses ◽  
Gas Bearing

Abstract Hydraulic fracture containment is discussed in relationship to linear elastic fracture mechanics. Three cases are analyzed,the effect of different material properties for the pay zone and the barrier formation,the characteristics of fracture propagation into regions of varying in-situ stress, propagation into regions of varying in-situ stress, andthe effect of hydrostatic pressure gradients on fracture propagation into overlying or underlying barrier formations. Analysis shows the importance of the elastic properties, the in-situ stresses, and the pressure gradients on fracture containment. Introduction Application of massive hydraulic fracture (MHF) techniques to the Rocky Mountain gas fields has been uneven, with some successes and some failures. The primary thrust of rock mechanics research in this area is to understand those factors that contribute to the success of MHF techniques and those conditions that lead to failures. There are many possible reasons why MHF techniques fail, including migration of the fracture into overlying or underlying barrier formations, degradation of permeability caused by application of hydraulic permeability caused by application of hydraulic fracturing fluid, loss of fracturing fluid into preexisting cracks or fissures, or extreme errors in preexisting cracks or fissures, or extreme errors in estimating the quantity of in-place gas. Also, a poor estimate of the in-situ permeability can result in failures that may "appear" to be caused by the hydraulic fracture process. Previous research showed that in-situ permeabilities can be one order of magnitude or more lower than permeabilities measured at near atmospheric conditions. Moreover, studies have investigated the degradation in both fracture permeability and formation permeability caused by the application of hydraulic fracture fluids. Further discussion of this subject is beyond the scope of this paper. This study will deal mainly with the containment of hydraulic fractures to the pay zone. In general, the lithology of the Rocky Mountain region is composed of oil- and gas-bearing sandstone layers interspaced with shales (Fig. 1). However, some sandstone layers may be water aquifers and penetration of the hydraulic fracture into these penetration of the hydraulic fracture into these aquifer layers is undesirable. Also, the shale layers can separate producible oil- and gas-bearing zones from nonproducible ones. Shale layers between the pay zone and other zones can be vital in increasing successful stimulation. If the shale layers act as barrier layers, the hydraulic fracture can be contained within the pay zone. The in-situ stresses and the stiffness, as characterized by the shear modulus of the zones, play significant roles in the containment of a play significant roles in the containment of a hydraulic fracture. The in-situ stresses result from forces in the earth's crust and constitute the compressive far-field stresses that act to close the hydraulic fracture. Fig. 2 shows a schematic representation of in-situ stresses acting on a vertical hydraulic fracture. Horizontal components of in-situ stresses may vary from layer to layer (Fig. 2). For example, direct measurements of in-situ stresses in shales has shown the minimum horizontal principal stress is nearly equal to the overburden principal stress is nearly equal to the overburden stress. SPEJ P. 27

The Impact of Layering and Permeable Frictional Interfaces on Hydraulic Fracturing in Unconventional Reservoirs

2021 ◽  
pp. 1-14
Author(s):  
Qian Gao ◽  
Ahmad Ghassemi
Keyword(s):  
Mechanical Properties ◽  
Hydraulic Fracture ◽  
Fracture Propagation ◽  
In Situ Stress ◽  
Height Growth ◽  
Interface Element ◽  
Hydraulic Fractures ◽  
Hydraulic Fracture Propagation ◽  
Fracture Height

Summary The impacts of formation layering on hydraulic fracture containment and on pumping energy are critical factors in a successful stimulation treatment. Conventionally, it is considered that the in-situ stress is the dominant factor controlling the fracture height. The influence of mechanical properties on fracture height growth is often ignored or is limited to consideration of different Young’s moduli. Also, it is commonly assumed that the interfaces between different layers are perfectly bounded without slippage, and interface permeability is not considered. In-situ experiments have demonstrated that variation of modulus and in-situ stress alone cannot explain the containment of hydraulic fractures observed in the field (Warpinski et al. 1998). Enhanced toughness, in-situ stress, interface slip, and energy dissipation in the layered rocks should be combined to contribute to the fracture containment analysis. In this study, we consider these factors in a fully coupled 3D hydraulic fracture simulator developed based on the finite element method. We use laboratory and numerical simulations to investigate these factors and how they affect hydraulic fracture propagation, height growth, and injection pressure. The 3D fully coupled hydromechanical model uses a special zero-thickness interface element and the cohesive zone model (CZM) to simulate fracture propagation, interface slippage, and fluid flow in fractures. The nonlinear mechanical behavior of frictional sliding along interface surfaces is considered. The hydromechanical model has been verified successfully through benchmarked analytical solutions. The influence of layered Young’s modulus on fracture height growth in layered formations is analyzed. The formation interfaces between different layers are simulated explicitly through the use of the hydromechanical interface element. The impacts of mechanical and hydraulic properties of the formation interfaces on hydraulic fracture propagation are studied. Hydraulic fractures tend to propagate in the layer with lower Young’s modulus so that soft layers could potentially act as barriers to limit the height growth of hydraulic fractures. Contrary to the conventional view, the location of hydraulic fracturing (in softer vs. stiffer layers) does affect fracture geometry evolution. In addition, depending on the mechanical properties and the conductivity of the interfaces, the shear slippage and/or opening along the formation interfaces could result in flow along the interface surfaces and terminate the fracture growth. The frictional slippage along the interfaces can serve as an effective mechanism of containment of hydraulic fractures in layered formations. It is suggested that whether a hydraulic fracture would cross a discontinuity depends not only on the layers’ mechanical properties but also on the hydraulic properties of the discontinuity; both the frictional slippage and fluid pressure along horizontal formation interfaces contribute to the reinitiation of a hydraulic fracture from a pre-existing flaw along the interfaces, producing an offset from the interception point to the reinitiation point.

Predicting Hydraulic Fracturing in a Carbonate Gas Reservoir in Abu Dhabi Using 1D Mechanical Earth Model: Uncertainty and Constraints

2015 ◽  
Author(s):  
Manhal Sirat ◽  
Mujahed Ahmed ◽  
Xing Zhang
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Natural Fracture ◽  
Abu Dhabi ◽  
Hydraulic Fractures ◽  
Gas Reservoir ◽  
In Situ Stresses ◽  
Tight Carbonate ◽  
Different Depths

Abstract In-situ stress state plays an important role in controlling fracture growth and containment in hydraulic fracturing managements. It is evident that the mechanical properties, existing stress regime and the natural fracture network of its reservoir rocks and the surrounding formations mainly control the geometry, size and containments of produced hydraulic fractures. Furthermore, the three principal in situ stresses' axes swap directions and magnitudes at different depths giving rise to identifying different mechanical bedrocks with corresponding stress regimes at different depths. Hence predicting the hydro-fractures can be theoretically achieved once all the above data are available. This is particularly difficult in unconventional and tight carbonate reservoirs, where heterogeneity and highly stress variation, in terms of magnitude and orientation, are expected. To optimize the field development plan (FDP) of a tight carbonate gas reservoir in Abu Dhabi, 1D Mechanical Earth Models (MEMs), involving generating the three principal in-situ stresses' profiles and mechanical property characterization with depth, have been constructed for four vertical wells. The results reveal the swap of stress magnitudes at different mechanical layers, which controls the dimension and orientation of the produced hydro-fractures. Predicted containment of the Hydro-fractures within the specific zones is likely with inevitable high uncertainty when the stress contrast between Sv, SHmax with Shmin respectively as well as Young's modulus and Poisson's Ratio variations cannot be estimated accurately. The uncertainty associated with this analysis is mainly related to the lacking of the calibration of the stress profiles of the 1D MEMs with minifrac and/or XLOT data, and both mechanical and elastic properties with rock mechanic testing results. This study investigates the uncertainty in predicting hydraulic fracture containment due to lacking such calibration, which highlights that a complete suite of data, including calibration of 1D MEMs, is crucial in hydraulic fracture treatment.

scholarly journals Apparent Toughness Anisotropy Induced by “Roughness” of In-Situ Stress: A Mechanism That Hinders Vertical Growth of Hydraulic Fractures and Its Simplified Modeling

SPE Journal ◽  
2019 ◽  
Vol 24 (05) ◽  
pp. 2148-2162 ◽  
Author(s):  
Pengcheng Fu ◽  
Jixiang Huang ◽  
Randolph R. Settgast ◽  
Joseph P. Morris ◽  
Frederick J. Ryerson
Keyword(s):  
Hydraulic Fracture ◽  
High Stress ◽  
In Situ Stress ◽  
Height Growth ◽  
Hydraulic Fractures ◽  
Simple Relationship ◽  
Vertical Growth ◽  
Stress Profiles ◽  
Fracture Height

Summary The height growth of a hydraulic fracture is known to be affected by many factors that are related to the layered structure of sedimentary rocks. Although these factors are often used to qualitatively explain why hydraulic fractures usually have well–bounded height growth, most of them cannot be directly and quantitatively characterized for a given reservoir to enable a priori prediction of fracture–height growth. In this work, we study the role of the “roughness” of in–situ–stress profiles, in particular alternating low and high stress among rock layers, in determining the tendency of a hydraulic fracture to propagate horizontally vs. vertically. We found that a hydraulic fracture propagates horizontally in low–stress layers ahead of neighboring high–stress layers. Under such a configuration, a fracture–mechanics principle dictates that the net pressure required for horizontal growth of high–stress layers within the current fracture height is significantly lower than that required for additional vertical growth across rock layers. Without explicit consideration of the stress–roughness profile, the system behaves as if the rock is tougher against vertical propagation than it is against horizontal fracture propagation. We developed a simple relationship between the apparent differential rock toughness and characteristics of the stress roughness that induce equivalent overall fracture shapes. This relationship enables existing hydraulic–fracture models to represent the effects of rough in–situ stress on fracture growth without directly representing the fine–resolution rough–stress profiles.

scholarly journals Laboratory Investigation on the -Effect of In-Situ Stresses on Hydraulic Fracture Containment

1982 ◽  
Vol 22 (03) ◽  
pp. 333-340 ◽  
Author(s):  
Norman R. Warpinski ◽  
James A. Clark ◽  
Richard A. Schmidt ◽  
Clarence W. Huddle
Keyword(s):  
Pore Pressure ◽  
Hydraulic Fracture ◽  
Laboratory Experiments ◽  
In Situ Stress ◽  
Enhanced Production ◽  
In Situ Stresses ◽  
Extensive Growth ◽  
Stress Variations ◽  
Fracture Growth

Abstract Laboratory experiments have been conducted to determine the effect of in-situ stress variations on hydraulic fracture containment. Fractures were initiated in layered rock samples with prescribed stress variations, and fracture growth characteristics were determined as a function of stress levels. Stress contrasts of 300 to 400 psi (2 to 3 MPa) were found sufficient to restrict fracture growth in laboratory samples of Nevada tuff and Tennessee and Nugget sandstones. The required stress level was found not to depend on mechanical rock properties. However, permeability and the resultant pore pressure effects were important. Tests conducted at biomaterial interfaces between Nugget and Tennessee sandstones show that the resultant stresses set up near the interface because of the applied overburden stress affect the fracture behavior in the same way as the applied confining stresses. These results provide a guideline for determining the in-situ stress contrast necessary to contain a fracture in a field treatment. Introduction An under-standing of the factors that influence and control hydraulic fracture containment is important for the successful use of hydraulic fracturing technology in the enhanced production of natural gas from tight reservoirs. Optimally, this understanding would provide improved fracture design criteria to maximize fracture surface area in contact with the reservoir with respect to volume injected and other treatment parameters. In formations with a positive containment condition (i.e., where fracturing out of zone is not anticipated), long penetrating fractures could be used effectively to develop the resource. For the opposite case, the options would beto use a small treatment so that large volumes are not wasted in out-of-zone fracturing and to accept a lower productivity improvement, orto reject the zone as uneconomical. These decisions cannot be made satisfactorily unless criteria for vertical fracture propagation are developed and techniques for readily measuring the important parameters are available. Currently, both theoretical and experimental efforts are being pursued to determine the important parameters and their relative effects on fracture growth. Two modes of fracture containment are possible. One is the situation where fracture growth is terminated at a discrete interface. Examples of this include laboratory experiments showing fracture termination at weak or unbonded interfaces and theoretical models that predict that fracture growth will terminate at a material property interface. The other mode may occur when the fracture propagates into the bounding layer, but extensive growth does not take place and the fracture thus is restricted. An example is the propagation of the fracture into a region with an adverse stress gradient so that continued propagation results in higher stresses on the fracture, which limits growth, as suggested by Simonson et al. and as seen in mineback experiments. Another example is the possible restriction caused by propagation into a higher modulus region where the decreased width results in increased pressure drop in the fracture, which might inhibit extensive growth into that region relative to the lower modulus region. Other parameters, such as natural fractures, treatment parameters, pore pressure, etc., may affect either of these modes. Laboratory and mineback experiments have shown that weak interfaces and in-situ stress differences are the most likely factors to contain the fracture, and weak interfaces are probably effective only at shallow depths. Thus, our experiments are being performed to determine the effect of in-situ stresses on fracture containment, both in a uniform rock sample and at material properly interfaces. SPEJ P. 333^

scholarly journals Numerical Investigation of Injection-Induced Fracture Propagation in Brittle Rocks with Two Injection Wells by a Modified Fluid-Mechanical Coupling Model

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4718
Author(s):  
Song Wang ◽  
Jian Zhou ◽  
Luqing Zhang ◽  
Zhenhua Han
Keyword(s):  
Fracture Propagation ◽  
In Situ Stress ◽  
Hydraulic Fractures ◽  
Fracture Networks ◽  
Breakdown Pressure ◽  
Injection Wells ◽  
Mechanical Coupling ◽  
Stress Shadow ◽  
Well Spacing

Hydraulic fracturing is a key technical means for stimulating tight and low permeability reservoirs to improve the production, which is widely employed in the development of unconventional energy resources, including shale gas, shale oil, gas hydrate, and dry hot rock. Although significant progress has been made in the simulation of fracturing a single well using two-dimensional Particle Flow Code (PFC2D), the understanding of the multi-well hydraulic fracturing characteristics is still limited. Exploring the mechanisms of fluid-driven fracture initiation, propagation and interaction under multi-well fracturing conditions is of great theoretical significance for creating complex fracture networks in the reservoir. In this study, a series of two-well fracturing simulations by a modified fluid-mechanical coupling algorithm were conducted to systematically investigate the effects of injection sequence and well spacing on breakdown pressure, fracture propagation and stress shadow. The results show that both injection sequence and well spacing make little difference on breakdown pressure but have huge impacts on fracture propagation pressure. Especially under hydrostatic pressure conditions, simultaneous injection and small well spacing increase the pore pressure between two injection wells and reduce the effective stress of rock to achieve lower fracture propagation pressure. The injection sequence can change the propagation direction of hydraulic fractures. When the in-situ stress is hydrostatic pressure, simultaneous injection compels the fractures to deflect and tend to propagate horizontally, which promotes the formation of complex fracture networks between two injection wells. When the maximum in-situ stress is in the horizontal direction, asynchronous injection is more conducive to the parallel propagation of multiple hydraulic fractures. Nevertheless, excessively small or large well spacing reduces the number of fracture branches in fracture networks. In addition, the stress shadow effect is found to be sensitive to both injection sequence and well spacing.

Investigation of the influence of natural fractures and in situ stress on hydraulic fracture propagation using a distinct-element approach

2015 ◽  
Vol 52 (7) ◽  
pp. 926-946 ◽  
Author(s):  
N. Zangeneh ◽  
E. Eberhardt ◽  
R.M. Bustin
Keyword(s):  
Rock Mass ◽  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Distinct Element ◽  
Fracture Propagation ◽  
In Situ Stress ◽  
Natural Fractures ◽  
Geological Conditions ◽  
Hydraulic Fracture Propagation

Hydraulic fracturing is the primary means for enhancing rock mass permeability and improving well productivity in tight reservoir rocks. Significant advances have been made in hydraulic fracturing theory and the development of design simulators; however, these generally rely on continuum treatments of the rock mass. In situ, the geological conditions are much more complex, complicated by the presence of natural fractures and planes of weakness such as bedding planes, joints, and faults. Further complexity arises from the influence of the in situ stress field, which has its own heterogeneity. Together, these factors may either enhance or diminish the effectiveness of the hydraulic fracturing treatment and subsequent hydrocarbon production. Results are presented here from a series of two-dimensional (2-D) numerical experiments investigating the influence of natural fractures on the modeling of hydraulic fracture propagation. Distinct-element techniques applying a transient, coupled hydromechanical solution are evaluated with respect to their ability to account for both tensile rupture of intact rock in response to fluid injection and shear and dilation along existing joints. A Voronoi tessellation scheme is used to add the necessary degrees of freedom to model the propagation path of a hydraulically driven fracture. The analysis is carried out for several geometrical variants related to hypothetical geological scenarios simulating a naturally fractured shale gas reservoir. The results show that key interactions develop with the natural fractures that influence the size, orientation, and path of the hydraulic fracture as well as the stimulated volume. These interactions may also decrease the size and effectiveness of the stimulation by diverting the injected fluid and proppant and by limiting the extent of the hydraulic fracture.

Sign in / Sign up

Export Citation Format

Share Document