Formation Damage Associated with Water-Based Drilling Fluids and Emulsified Acid Study

1999 ◽  
Author(s):  
J.D. Lynn ◽  
H.A. Nasr-El-Din
Keyword(s):  
Formation Damage ◽  
Drilling Fluids ◽  
Water Based

scholarly journals Experimental study on thermal, rheological and filtration control characteristics of drilling fluids: effect of nanoadditives

2020 ◽  
Vol 75 ◽  
pp. 36
Author(s):  
Erfan Veisi ◽  
Mastaneh Hajipour ◽  
Ebrahim Biniaz Delijani
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Drilling Fluid ◽  
Formation Damage ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Drill Bit ◽  
Rheological Characteristics ◽  
Cu Nanoparticles ◽  
Water Based

Cooling the drill bit is one of the major functions of drilling fluids, especially in high temperature deep drilling operations. Designing stable drilling fluids with proper thermal properties is a great challenge. Identifying appropriate additives for the drilling fluid can mitigate drill-bit erosion or deformation caused by induced thermal stress. The unique advantages of nanoparticles may enhance thermal characteristics of drilling fluids. The impacts of nanoparticles on the specific heat capacity, thermal conductivity, rheological, and filtration control characteristics of water‐based drilling fluids were experimentally investigated and compared in this study. Al2O3, CuO, and Cu nanoparticles were used to prepare the water-based drilling nanofluid samples with various concentrations, using the two-step method. Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD) were utilized to study the nanoparticle samples. The nanofluids stability and particle size distribution were, furthermore, examined using Dynamic Light Scattering (DLS). The experimental results indicated that thermal and rheological characteristics are enhanced in the presence of nanoparticles. The best enhancement in drilling fluid heat capacity and thermal conductivity was obtained as 15.6% and 12%, respectively by adding 0.9 wt% Cu nanoparticles. Furthermore, significant improvement was observed in the rheological characteristics such as the apparent and plastic viscosities, yield point, and gel strength of the drilling nanofluids compared to the base drilling fluid. Addition of nanoparticles resulted in reduced fluid loss and formation damage. The permeability of filter cakes decreased with increasing the nanoparticles concentration, but no significant effect in filter cake thickness was observed. The results reveal that the application of nanoparticles may reduce drill-bit replacement costs by improving the thermal and drilling fluid rheological characteristics and decrease the formation damage due to mud filtrate invasion.

Loss Circulation and Formation Damage Control on Overbalanced Drilling With Different Formulations of Water Based Drill-In Fluids on Sandstone Reservoir

2012 ◽  
Author(s):  
Leandro F. Lopes ◽  
Bruno O. Silveira ◽  
Rosângela B. Z. L. Moreno
Keyword(s):  
Reverse Flow ◽  
Damage Control ◽  
Fluid Management ◽  
Formation Damage ◽  
Drilling Fluids ◽  
Reservoir Water ◽  
Well Productivity ◽  
Water Based ◽  
Permeability Impairment ◽  
Productivity Ratio

The oil well drilling should not damage formation, mainly the interest region: the reservoir. Drilling without damaging the reservoir is a hard challenge, and therefore the development of technologies and optimization process, including, for example, the design of fluids in order to minimize damage, is been stimulated. Drilling fluids may interact with reservoir rocks resulting on permeability impairment, which reduces well productivity. It has been reported that a detailed fluid management plan can help to minimize formation damage and improve well productivity. This work is focused on formation damage analysis due to drilling fluids invasion in high permeability sandstone oil reservoir. Water-based fluids were prepared with the following components: distilled water, salt (NaI), polymer (Partially Hydrolyzed Polyacrylamide - HPAM, and Xanthan Gum - XG) and clay (Bentonite). Samples were submitted to an invasion process, simulating an overbalanced drilling, and to an oil reverse flow, simulating oil production beginning. Results showed that all fluids containing clay presented less deep invasion than the fluids prepared with polymer only. Moreover, clay concentration influenced on permeability impairment and productivity ratio return results. HPAM fluids, when injected, invaded more deeply the samples than XG fluids, but productivity ratio return was also higher.

scholarly journals Utilization of Eco-Friendly Waste Generated Nanomaterials in Water-Based Drilling Fluids; State of the Art Review

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4171
Author(s):  
Rabia Ikram ◽  
Badrul Mohamed Jan ◽  
Akhmal Sidek ◽  
George Kenanakis
Keyword(s):  
State Of The Art ◽  
Superior Performance ◽  
Future Research ◽  
Drilling Fluids ◽  
Drill Cuttings ◽  
Environmental Friendly ◽  
Water Based ◽  
Drilling Operations ◽  
Filtration Properties

An important aspect of hydrocarbon drilling is the usage of drilling fluids, which remove drill cuttings and stabilize the wellbore to provide better filtration. To stabilize these properties, several additives are used in drilling fluids that provide satisfactory rheological and filtration properties. However, commonly used additives are environmentally hazardous; when drilling fluids are disposed after drilling operations, they are discarded with the drill cuttings and additives into water sources and causes unwanted pollution. Therefore, these additives should be substituted with additives that are environmental friendly and provide superior performance. In this regard, biodegradable additives are required for future research. This review investigates the role of various bio-wastes as potential additives to be used in water-based drilling fluids. Furthermore, utilization of these waste-derived nanomaterials is summarized for rheology and lubricity tests. Finally, sufficient rheological and filtration examinations were carried out on water-based drilling fluids to evaluate the effect of wastes as additives on the performance of drilling fluids.

scholarly journals Wet Drilled Cuttings Bed Rheology

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1644
Author(s):  
Camilo Pedrosa ◽  
Arild Saasen ◽  
Bjørnar Lund ◽  
Jan David Ytrehus
Keyword(s):  
Drilling Fluid ◽  
Drilling Fluids ◽  
Parallel Plates ◽  
Single Particles ◽  
Cuttings Transport ◽  
Transport Studies ◽  
Water Based ◽  
Fluid Properties ◽  
External Forces ◽  
Cuttings Bed

The cuttings transport efficiency of various drilling fluids has been studied in several approaches. This is an important aspect, since hole cleaning is often a bottleneck in well construction. The studies so far have targeted the drilling fluid cuttings’ transport capability through experiments, simulations or field data. Observed differences in the efficiency due to changes in the drilling fluid properties and compositions have been reported but not always fully understood. In this study, the cuttings bed, wetted with a single drilling fluid, was evaluated. The experiments were performed with parallel plates in an Anton Paar Physica 301 rheometer. The results showed systematic differences in the internal friction behaviors between tests of beds with oil-based and beds with water-based fluids. The observations indicated that cutting beds wetted with a polymeric water-based fluid released clusters of particles when external forces overcame the bonding forces and the beds started to break up. Similarly, it was observed that an oil-based fluid wetted bed allowed particles to break free as single particles. These findings may explain the observed differences in previous cutting transport studies.

Sign in / Sign up

Export Citation Format

Share Document