Stabilization Of In-Situ Hydrates Enhances Drilling Performance And Rig Safety

1997 ◽  
Author(s):  
T.R. Schofield ◽  
A. Judzis ◽  
M. Yousif
Keyword(s):  
Drilling Performance

In-situ investigation of drilling performance and bit wear on an electrical drill hammer

2022 ◽  
Vol 122 ◽  
pp. 104348
Author(s):  
Guangzhe Zhang ◽  
Kurosch Thuro ◽  
Heinz Konietzky ◽  
Florian M. Menschik ◽  
Heiko Käsling ◽  
...  
Keyword(s):  
Drilling Performance ◽  
Bit Wear ◽  
In Situ Investigation

scholarly journals Prediction Model of Drilling Performance for Percussive Rock Drilling Tool

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Dae-Ji Kim ◽  
Jaewon Kim ◽  
Booyeong Lee ◽  
Min-Seok Shin ◽  
Joo-Young Oh ◽  
...  
Keyword(s):  
Prediction Model ◽  
Dynamic Effect ◽  
Drill Bit ◽  
Motion Model ◽  
Percussive Drilling ◽  
Drilling Tool ◽  
Rock Types ◽  
Drilling Performance ◽  
The Impact

This study suggests a method for quantitatively estimating the drilling performance of the down-the-hole (DTH) hammer during percussive drilling of rock surfaces. A pneumatic dynamic model of the DTH hammer was developed that considers the mass flow rate relations representing the orifice opening areas of the air tube, the piston, and bit flushing channels. A drill bit motion model was developed to represent the dynamics of a drill bit impacted by a dropped piston and explain the impact stress propagation and rock-crushing mechanism. The rock-crushing effect of the drill button bit was measured through a piston drop test. The pneumatic hammer model and drill bit motion model were then combined in a prediction model to determine the impact efficiency according to different rock types (i.e., soft, medium-hard, and very hard). The drilling efficiency was defined as the input value of the prediction model, which was used to simulate the drilling performance of DTH hammers considering the rock type and dynamic effect of the drill bit. Finally, the simulation results were compared with the results of in situ drilling tests for verification.

Rendez vous with Saturn's rings

1984 ◽  
Vol 75 ◽  
pp. 743-759 ◽  
Author(s):  
Kerry T. Nock
Keyword(s):  
Solar Energy ◽  
Electric Propulsion ◽  
Power Source ◽  
Propulsion System ◽  
Low Thrust ◽  
Ring Plane ◽  
The Earth ◽  
Total Impulse ◽  
Saturn's Rings

ABSTRACTA mission to rendezvous with the rings of Saturn is studied with regard to science rationale and instrumentation and engineering feasibility and design. Future detailedin situexploration of the rings of Saturn will require spacecraft systems with enormous propulsive capability. NASA is currently studying the critical technologies for just such a system, called Nuclear Electric Propulsion (NEP). Electric propulsion is the only technology which can effectively provide the required total impulse for this demanding mission. Furthermore, the power source must be nuclear because the solar energy reaching Saturn is only 1% of that at the Earth. An important aspect of this mission is the ability of the low thrust propulsion system to continuously boost the spacecraft above the ring plane as it spirals in toward Saturn, thus enabling scientific measurements of ring particles from only a few kilometers.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Structural Studies on Mitotic Spindle Fibres

1978 ◽  
Vol 36 (3) ◽  
pp. 615-626
Author(s):  
J.R. Mcintosh
Keyword(s):  
Chemical Composition ◽  
Mitotic Spindle ◽  
Structural Studies ◽  
Mitotic Apparatus ◽  
Chemical Studies ◽  
Medical Interest ◽  
Spindle Fibres

The mitotic apparatus is a structure of obvious biological and medical interest, but it has proved to be a difficult cellular machine to understand. The chemical composition of the spindle is only slightly elucidated, largely because of the difficulties in preparing useful isolates of the structure. Chemical studies of the mitotic spindle have been reviewed elsewhere (Mcintosh, 1977), and will not be discussed further here. One would think that structural studies on the mitotic apparatus (MA) in situ would be straightforward, but even with this approach there is some disagreement in the results obtained with various methods and by different investigators. In this paper I will review briefly the approaches which have been used in structural studies of the MA, pointing out the strengths and problems of each approach. I will summarize the principal findings of the different methods, and identify what seem to be fruitful avenues for further work.

Sign in / Sign up

Export Citation Format

Share Document