Cyclic Steam Injection With Additives: Laboratory and Field Test Results of Steam/Foam and Steam/Solvent Processes

Author(s):  
Zuleyka Mendez ◽  
J.M. Alvarez ◽  
Elena Escobar ◽  
Peter Colonomos ◽  
Enrique Campos
1993 ◽  
Vol 115 (3) ◽  
pp. 537-546 ◽  
Author(s):  
J. P. Claeys ◽  
K. M. Elward ◽  
W. J. Mick ◽  
R. A. Symonds

This paper presents the results of the combustion system test of the MS7001F installed at the Virginia Power Chesterfield station. Tests of water and steam injection for NOx control were performed. Results of emissions, combustor dynamics, and combustor hardware performance are presented. Emissions test results include NOx, CO, unburned hydrocarbons, VOC, and formaldehyde levels. Combustor dynamic activity over a range of diluent injection ratios, and the performance of an actively cooled transition duct are also discussed. Combustion system mechanical performance is described following the first combustion system inspection.


1987 ◽  
Vol 109 (3) ◽  
pp. 257-262 ◽  
Author(s):  
J. B. Burnham ◽  
M. H. Giuliani ◽  
D. J. Moeller

This paper describes the first full-scale field test of a steam injection system for a natural-gas-fired G.E. LM5000 gas generator for the purpose of: (a) decreased exhaust emissions, (b) increased power output, and (c) improved efficiency. It discusses the steam supply system, engine features, test results, and plant economics for steam injection into the combustor and compressor discharge sections of the LM5000 at rates up to 65,000 lb/hr (29,510 kg/hr).


Author(s):  
James B. Burnham ◽  
Michael H. Giuliani ◽  
David J. Moeller

This paper describes the first full scale field test of a steam injection system for a natural gas fired G.E. LM5000 gas generator for the purpose of: (A) decreased exhaust emissions, (B) increased power output, and (C) improved efficiency. It discusses the steam supply system, engine features, test results and plant economics for steam injection into the combustor and compressor discharge sections of the LM5000 at rates up to 65,000 LB/HR (29,510 KG/HR).


Author(s):  
James P. Claeys ◽  
Kevin M. Elward ◽  
Warren J. Mick ◽  
Richard A. Symonds

This paper presents the results of the combustion system test of the MS7001F installed at the Virginia Power Chesterfield station. Tests of water and steam injection for NOx control were performed. Results of emissions, combustor dynamics, and combustor hardware performance are presented. Emissions test results include NOx, CO, unburned hydrocarbons, VOC and formaldehyde levels. Combustor dynamic activity over a range of diluent injection ratios, and the performance of an actively cooled transition duct are also discussed. Combustion system mechanical performance is described following the first combustion system inspection.


1990 ◽  
Author(s):  
David M. Bailey ◽  
Stuart D. Foltz ◽  
Myer J. Rosenfield
Keyword(s):  

2021 ◽  
Vol 13 (10) ◽  
pp. 5708
Author(s):  
Bo-Ram Park ◽  
Ye-Seul Eom ◽  
Dong-Hee Choi ◽  
Dong-Hwa Kang

The purpose of this study was to evaluate outdoor PM2.5 infiltration into multifamily homes according to the building characteristics using regression models. Field test results from 23 multifamily homes were analyzed to investigate the infiltration factor and building characteristics including floor area, volume, outer surface area, building age, and airtightness. Correlation and regression analysis were then conducted to identify the building factor that is most strongly associated with the infiltration of outdoor PM2.5. The field tests revealed that the average PM2.5 infiltration factor was 0.71 (±0.19). The correlation analysis of the building characteristics and PM2.5 infiltration factor revealed that building airtightness metrics (ACH50, ELA/FA, and NL) had a statistically significant (p < 0.05) positive correlation (r = 0.70, 0.69, and 0.68, respectively) with the infiltration factor. Following the correlation analysis, a regression model for predicting PM2.5 infiltration based on the ACH50 airtightness index was proposed. The study confirmed that the outdoor-origin PM2.5 concentration in highly leaky units could be up to 1.59 times higher than that in airtight units.


2017 ◽  
Author(s):  
P. Millot ◽  
F. K. Wong ◽  
D. A. Rose ◽  
T. Zhou ◽  
R. Grover ◽  
...  

2008 ◽  
Author(s):  
V.G. Bedrin ◽  
M.M. Khasanov ◽  
R.A. Khabibullin ◽  
V.A. Krasnov ◽  
A.A. Pashali ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document