Case Study of Two Horizontal Wells for Improved Oil Recovery in New Zealand

1992 ◽  
Vol 44 (09) ◽  
pp. 1033-1039
Author(s):  
L.R. Stoltz
Keyword(s):  
New Zealand ◽  
Oil Recovery ◽  
Horizontal Wells ◽  
Improved Oil Recovery

Use of Downhole Oil-Water Separation System in Horizontal Wells

2021 ◽  
Author(s):  
Ahmed Alshmakhy ◽  
Ali Abdelkerim ◽  
Nils Braaten
Keyword(s):  
Oil Recovery ◽  
Produced Water ◽  
Financial Analysis ◽  
Mechanical Design ◽  
Flow Simulation ◽  
Horizontal Wells ◽  
Processing Plant ◽  
Water Separation ◽  
Improved Oil Recovery ◽  
Water Cut

Abstract This paper will focus on a new system for separation of water in downhole horizontal wells. The advantages with the system are related to the fact that the water produced from the well is not lifted to the surface, but re-injected into suitable parts of the reservoir, either for pressure support or for diposal. The method of water separation and re-injection has been evaluated for oil producing fields. The paper presents details of the technical solutions and analysis done related to the financial analysis/payback. The mechanical design is basically a main pipe section of a few meters of length, with a special geometry utilizing gravity-based separation. A technical and economic analysis of a downhole processing plant (DPP) using a horizontally installed water/oil separator has been performed. The Improved Oil Recovery (IOR)part has been analysed with a relevant flow simulation tool. Based on the given reservoir depth/pressure, flow rate, viscosity/density and water cut, the simulations show that a significant improved production rate/income can be achieved by extracting the produced water downhole and performing re-injection into the producing reservoir to maintain reservoir pressure. In addition, the expected lifetime of the well is increased by several years. The conclusion is that the earlier the separator is installed, the greater the total well income. In addition, details regarding not only multi-lateral wells through level 5 junctions but also production string with separator and valve system has been evaluated and is concluded to be feasible for the well in question The removal of water downhole has several advantages, for example the removal of the water column up to the surface will reduce the reservoir back pressure and will improve recovery /production rates. In addition, not lifting the water will reduce energy consumption/CO2 footprint, and removal of water will reduce surface processing and possible re-injection and chemical treatment cost. In general, water separation downhole is advantageous, due to the higher pressure.

Improved oil recovery by raw water injection using horizontal wells

2009 ◽  
Vol 49 (1) ◽  
pp. 453
Author(s):  
Pavel Bedrikovetsky ◽  
Mohammad Afiq ab Wahab ◽  
Gladys Chang ◽  
Antonio Luiz Serra de Souza ◽  
Claudio Alves Furtado
Keyword(s):  
Oil Recovery ◽  
Filter Cake ◽  
Produced Water ◽  
Water Injection ◽  
Horizontal Wells ◽  
Water Flooding ◽  
Sweep Efficiency ◽  
Improved Oil Recovery ◽  
The North ◽  
Reservoir Simulator

Injectivity formation damage with water-flooding using sea/produced water has been widely reported in the North Sea, the Gulf of Mexico and the Campos Basin in Brazil. The damage is due to the capture of solid/liquid particles by the rock with consequent permeability decline; it is also due to the formation of a low permeable external filter cake. Yet, moderate injectivity decline is not too damaging with long horizontal injectors where the initial injectivity is high. In this case, injection of raw or poorly treated water would save money on water treatment, which is not only cumbersome but also an expensive procedure in offshore projects. In this paper we investigate the effects of injected water quality on waterflooding using horizontal wells. It was found that induced injectivity damage results in increased sweep efficiency. The explanation of the phenomenon is as follows: injectivity rate is distributed along a horizontal well non-uniformly; water advances faster from higher rate intervals resulting in early breakthrough; the retained particles plug mostly the high permeability channels and homogenise the injectivity profile along the well. An analytical model for injectivity decline accounting for particle capture and a low permeable external filter cake formation has been implemented into the Eclipse 100 reservoir simulator. It is shown that sweep efficiency in a heterogeneous formation can increase by up to 5% after one pore volume injected, compared to clean water injection.

Sign in / Sign up

Export Citation Format

Share Document