The Use of Interpolation to Obtain Shape Factors for Pressure Buildup Calculations

1968 ◽  
Vol 20 (05) ◽  
pp. 449-450 ◽  
Author(s):  
Robert C. Earlougher
Keyword(s):  
Shape Factors ◽  
Pressure Buildup

Development of a Transient Model for Fluid Flow, Heat Transfer and Pressure Buildup in Wellbores

2020 ◽  
Author(s):  
Ianto Martins ◽  
Arthur Pandolfo da Veiga ◽  
Eduardo Alves ◽  
Jader Barbosa
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Transient Model ◽  
Pressure Buildup ◽  
Flow Heat

Comparison of copper sulphate pentahydrate growth rates determined by different methods

1990 ◽  
Vol 55 (7) ◽  
pp. 1691-1707 ◽  
Author(s):  
Miloslav Karel ◽  
Jiří Hostomský ◽  
Jaroslav Nývlt ◽  
Axel König
Keyword(s):  
Growth Rate ◽  
Crystal Growth ◽  
Fluidized Bed ◽  
Growth Rates ◽  
Copper Sulphate ◽  
Crystal Growth Rate ◽  
Effect Of Temperature ◽  
Rotating Disc ◽  
Shape Factors ◽  
Data Treatment

Crystal growth rates of copper sulphate pentahydrate (CuSO4.5 H2O) determined by different authors and methods are compared. The methods included in this comparison are: (i) Measurement on a fixed crystal suspended in a streaming solution, (ii) measurement on a rotating disc, (iii) measurement in a fluidized bed, (iv) measurement in an agitated suspension. The comparison involves critical estimation of the supersaturation used in measurements, of shape factors used for data treatment and a correction for the effect of temperature. Conclusions are drawn for the choice of values to be specified when data of crystal growth rate measurements are published.

scholarly journals The Impact of Filler Geometry on Polylactic Acid-Based Sustainable Polymer Composites

Molecules ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 149
Author(s):  
Karol Leluk ◽  
Stanisław Frąckowiak ◽  
Joanna Ludwiczak ◽  
Tomasz Rydzkowski ◽  
Vijay Kumar Thakur
Keyword(s):  
Polymer Composites ◽  
Polylactic Acid ◽  
Matrix Material ◽  
Chemical Properties ◽  
Precipitated Calcium Carbonate ◽  
Cellulose Fibres ◽  
Shape Factors ◽  
Pure Cellulose ◽  
Physico Chemical ◽  
The Impact

Recently, biocomposites have emerged as materials of great interest to the scientists and industry around the globe. Among various polymers, polylactic acid (PLA) is a popular matrix material with high potential for advanced applications. Various particulate materials and nanoparticles have been used as the filler in PLA based matrix. One of the extensively studied filler is cellulose. However, cellulose fibres, due to their hydrophilic nature, are difficult to blend with a hydrophobic polymer matrix. This leads to agglomeration and creates voids, reducing the mechanical strength of the resulting composite. Moreover, the role of the various forms of pure cellulose and its particle shape factors has not been analyzed in most of the current literature. Therefore, in this work, materials of various shapes and shape factors were selected as fillers for the production of polymer composites using Polylactic acid as a matrix to fill this knowledge gap. In particular, pure cellulose fibres (three types with different elongation coefficient) and two mineral nanocomponents: precipitated calcium carbonate and montmorillonite were used. The composites were prepared by a melt blending process using two different levels of fillers: 5% and 30%. Then, the analysis of their thermomechanical and physico-chemical properties was carried out. The obtained results were presented graphically and discussed in terms of their shape and degree of filling.

Radiation Shape Factors for Channels With Varying Cross Sections

1988 ◽  
Vol 110 (1) ◽  
pp. 264-266 ◽  
Author(s):  
T. L. Eddy ◽  
G. E. Nielsson
Keyword(s):  
Cross Sections ◽  
Shape Factors

scholarly journals Shape Factors in Low‐Frequency Noise Reduction

1967 ◽  
Vol 42 (5) ◽  
pp. 1202-1203
Author(s):  
J. Ronald Bailey ◽  
Franklin D. Hart
Keyword(s):  
Noise Reduction ◽  
Low Frequency ◽  
Frequency Noise ◽  
Low Frequency Noise ◽  
Shape Factors
Sign in / Sign up

Export Citation Format

Share Document