Enhanced Experimental Carbon Dioxide Sweep Using Surface Coated Silica Nanoparticles as a Foaming Agent

2021 ◽  
Author(s):  
Ahmad Alfakher ◽  
David A. DiCarlo
Keyword(s):  
Carbon Dioxide ◽  
Silica Nanoparticles ◽  
Oil Recovery ◽  
Graphical Representation ◽  
Co2 Flooding ◽  
Sweep Efficiency ◽  
Foaming Agent ◽  
The Core ◽  
Co2 Foam

Abstract Solvent flooding is a well-established method of enhanced oil recovery (EOR), with carbon dioxide (CO2) being the most-often used solvent. As CO2 is both less viscous and less dense than the fluids it displaces, the displacement suffers from poor sweep efficiency caused by an unfavorable mobility ratio and unfavorable gravity number. Creating in-situ CO2 foam improves the sweep efficiency of CO2 floods. Another application is the injection of CO2 foam into saline aquifers for carbon capture and storage (CCS). The goal of the core flood experiments in this paper was to study the effectiveness of surface coated silica nanoparticles as an in-situ CO2 foaming agent. In each experiment, the pressure drop was measured across five separate sections in the core, as well as along the whole core. In addition, the saturation distribution in the core was calculated periodically using computed tomography (CT) scanning measurements. The experiments consisted of vertical core floods where liquid CO2 displaced brine from the top to the bottom of the core. A flood with surface coated silica nanoparticles suspended in the brine is performed in the same core and at the same conditions to a flood with no nanoparticles, and results from these floods are compared. In these experiments, breakthrough occurred 45% later with foamed CO2, and the final CO2 saturation was also 45% greater than with the unfoamed CO2. The study shows how nanoparticles stabilize the CO2 front. The results provide quantitative information on, as well as a graphical representation of, the behavior of the CO2 foam front as it advances through the core. This data can be used to upscale the behavior observed and properties calculated from the core-scale to the reservoir-scale to improve field applications of CO2 flooding.

The Effect of Phase Equilibria on the CO2 Displacement Mechanism

1979 ◽  
Vol 19 (04) ◽  
pp. 242-252 ◽  
Author(s):  
R.S. Metcalfe ◽  
Lyman Yarborough
Keyword(s):  
Carbon Dioxide ◽  
Phase Equilibria ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Miscible Displacement ◽  
Co2 Flooding ◽  
Recovery Method ◽  
Two Fluids ◽  
Reservoir Conditions

Abstract Carbon dioxide flooding under miscible conditions is being developed as a major process for enhanced oil recovery. This paper presents results of research studies to increase our understanding of the multiple-contact miscible displacement mechanism for CO2 flooding. Carbon dioxide displacements of three synthetic oils of increasing complexity (increasing number of hydrocarbon components) are described. The paper concentrates on results of laboratory flow studies, but uses results of phase-equilibria and numerical studies to support the conclusions.Results from studies with synthetic oils show that at least two multiple-contact miscible mechanisms, vaporization and condensation, can be identified and that the phase-equilibria data can be used as a basis for describing the mechanism. The phase-equilibria change with varying reservoir conditions, and the flow studies show that the miscible mechanism depends on the phase-equilibria behavior. Qualitative predictions with mathematical models support our conclusions.Phase-equilibria data with naturally occurring oils suggest the two mechanisms (vaporization and condensation) are relevant to CO2 displacements at reservoir conditions and are a basis for specifying the controlling mechanisms. Introduction Miscible-displacement processes, which rely on multiple contacts of injected gas and reservoir oil to develop an in-situ solvent, generally have been recognized by the petroleum industry as an important enhanced oil-recovery method. More recently, CO2 flooding has advanced to the position (in the U.S.) of being the most economically attractive of the multiple-contact miscibility (MCM) processes. Several projects have been or are currently being conducted either to study or use CO2 as an enhanced oil-recovery method. It has been demonstrated convincingly by Holm and others that CO2 can recover oil from laboratory systems and therefore from the swept zone of petroleum reservoirs using miscible displacement. However, several contradictions seem to exist in published results.. These authors attempt to establish the mechanism(s) through which CO2 and oil form a miscible solvent in situ. (The solvent thus produced is capable of performing as though the two fluids were miscible when performing as though the two fluids were miscible when injected.) In addition, little experimental work has been published to provide support for the mechanisms of multiple-contact miscibility, as originally discussed by Hutchinson and Braun.One can reasonably assume that the miscible CO2 process will be related directly to phase equilibria process will be related directly to phase equilibria because it involves intimate contact of gases and liquids. However, no data have been published to indicate that the mechanism for miscibility development may differ for varying phase-equilibria conditions.This paper presents the results of both flow and phase-equilibria studies performed to determine the phase-equilibria studies performed to determine the mechanism(s) of CO2 multiple-contact miscibility. These flow studies used CO2 to displace three multicomponent hydrocarbon mixtures under first-contact miscible, multiple-contact miscible, and immiscible conditions. Results are presented to support the vaporization mechanism as described by Hutchinson and Braun, and also to show that more than one mechanism is possible with CO2 displacements. The reason for the latter is found in the results of phase-equilibria studies. SPEJ P. 242

Mobility of Ethomeen C12 and Carbon Dioxide (CO2) Foam at High Temperature/High Salinity and in Carbonate Cores

SPE Journal ◽  
2016 ◽  
Vol 21 (04) ◽  
pp. 1151-1163 ◽  
Author(s):  
Leyu Cui ◽  
Kun Ma ◽  
Maura Puerto ◽  
Ahmed A. Abdala ◽  
Ivan Tanakov ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
High Temperature ◽  
High Salinity ◽  
Local Equilibrium ◽  
Co2 Flooding ◽  
Sweep Efficiency ◽  
Co2 Foam ◽  
Foam Model ◽  
Wide Range ◽  
Carbon Dioxide Co2

Summary The low viscosity and density of carbon dioxide (CO2) usually result in the poor sweep efficiency in CO2-flooding processes, especially in heterogeneous formations. Foam is a promising method to control the mobility and thus reduce the CO2 bypass because of the gravity override and heterogeneity of formations. A switchable surfactant, Ethomeen C12, has been reported as an effective CO2-foaming agent in a sandpack with low adsorption on pure-carbonate minerals. Here, the low mobility of Ethomeen C12/CO2 foam at high temperature (120 °C), high pressure (3,400 psi), and high salinity [22 wt% of total dissolved solids (TDS)] was demonstrated in Silurian dolomite cores and in a wide range of foam qualities. The influence of various parameters, including aqueous solubility, thermal and chemical stability, flow rate, foam quality, salinity, temperature, and minimum-pressure gradient (MPG), on CO2 foam was discussed. A local-equilibrium foam model, the dry-out foam model, was used to fit the experimental data for reservoir simulation.

Visualizing and Quantifying Generation, Propagation, and Sweep of Nanocellulose-Strengthened Carbon Dioxide Foam in a Complex 2D Heterogeneous Fracture Network Model

SPE Journal ◽  
2021 ◽  
pp. 1-14
Author(s):  
Bing Wei ◽  
Qingtao Tian ◽  
Shengen Chen ◽  
Xingguang Xu ◽  
Dianlin Wang ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Network Model ◽  
Gravitational Effect ◽  
Fracture Network ◽  
Sweep Efficiency ◽  
Co2 Foam ◽  
Reservoir Conditions ◽  
Foam Film ◽  
Carbon Dioxide Co2

Summary There exist two main issues hampering the wide application and development of carbon dioxide (CO2) foam in conformance improvement and CO2 mobility reduction in fractured systems: (1) instability of foam film under reservoir conditions and (2) uncertainties of foam flow in complex fractures. To address these two issues, we previously developed a series of nanocellulose-strengthened CO2 foam (referred to as NCF-st-CO2 foam), while the primary goal of this work is to thoroughly elucidate generation, propagation, and sweep of NCF-st-CO2 foam in a visual 2D heterogeneous fracture network model. NCF-st-CO2 foam outperformed CO2 foam in reducing gas mobility during either coinjection (COI) or surfactant-alternating-gas (SAG) injection, and the threshold foam quality was approximately 0.67. Foam creation was increased with the total superficial velocity for CO2 foam and almost stayed constant for NCF-st-CO2 foam in fractures during COI. For SAG, large surfactant slug could prevent CO2 from early breakthrough and facilitate foaming in situ. The improved sweep efficiency induced by NCF-st-CO2 foam occurred near the producer for both COI and SAG. Film division and behind mainly led to foam generation in the fracture model. Gravity segregation and override was insignificant during COI but became noticeable during SAG, which caused the sweep efficiency decrease by 3 to 9%. Owing to the enhanced film, NCF-st-CO2 foam enabled mitigation of the gravitational effect, especially around the producer.

Performance of Silica Nanoparticles in CO2 Foam for EOR and CCUS at Tough Reservoir Conditions

SPE Journal ◽  
2019 ◽  
Vol 25 (01) ◽  
pp. 406-415 ◽  
Author(s):  
Arthur U. Rognmo ◽  
Noor Al-Khayyat ◽  
Sandra Heldal ◽  
Ida Vikingstad ◽  
Øyvind Eide ◽  
...  
Keyword(s):  
Silica Nanoparticles ◽  
Oil Recovery ◽  
Carbon Capture ◽  
Elevated Temperatures ◽  
Co2 Storage ◽  
Sweep Efficiency ◽  
Co2 Foam ◽  
Reservoir Conditions ◽  
Incremental Oil Recovery ◽  
Surface Modified

Summary The use of nanoparticles for CO2-foam mobility is an upcoming technology for carbon capture, utilization, and storage (CCUS) in mature fields. Silane-modified hydrophilic silica nanoparticles enhance the thermodynamic stability of CO2 foam at elevated temperatures and salinities and in the presence of oil. The aqueous nanofluid mixes with CO2 in the porous media to generate CO2 foam for enhanced oil recovery (EOR) by improving sweep efficiency, resulting in reduced carbon footprint from oil production by the geological storage of anthropogenic CO2. Our objective was to investigate the stability of commercially available silica nanoparticles for a range of temperatures and brine salinities to determine if nanoparticles can be used in CO2-foam injections for EOR and underground CO2 storage in high-temperature reservoirs with high brine salinities. The experimental results demonstrated that surface-modified nanoparticles are stable and able to generate CO2 foam at elevated temperatures (60 to 120°C) and extreme brine salinities (20 wt% NaCl). We find that (1) nanofluids remain stable at extreme salinities (up to 25 wt% total dissolved solids) with the presence of both monovalent (NaCl) and divalent (CaCl2) ions; (2) both pressure gradient and incremental oil recovery during tertiary CO2-foam injections were 2 to 4 times higher with nanoparticles compared with no-foaming agent; and (3) CO2 stored during CCUS with nanoparticle-stabilized CO2 foam increased by more than 300% compared with coinjections without nanoparticles.

scholarly journals Experimental Investigation of Polymer-Coated Silica Nanoparticles for EOR under Harsh Reservoir Conditions of High Temperature and Salinity

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 765
Author(s):  
Alberto Bila ◽  
Ole Torsæter
Keyword(s):  
High Temperature ◽  
Silica Nanoparticles ◽  
Oil Recovery ◽  
Data Bank ◽  
Sweep Efficiency ◽  
Reservoir Conditions ◽  
Wet Condition ◽  
Incremental Oil Recovery ◽  
Original Oil In Place

Laboratory experiments have shown higher oil recovery with nanoparticle (NPs) flooding. Accordingly, many studies have investigated the nanoparticle-aided sweep efficiency of the injection fluid. The change in wettability and the reduction of the interfacial tension (IFT) are the two most proposed enhanced oil recovery (EOR) mechanisms of nanoparticles. Nevertheless, gaps still exist in terms of understanding the interactions induced by NPs that pave way for the mobilization of oil. This work investigated four types of polymer-coated silica NPs for oil recovery under harsh reservoir conditions of high temperature (60 ∘C) and salinity (38,380 ppm). Flooding experiments were conducted on neutral-wet core plugs in tertiary recovery mode. Nanoparticles were diluted to 0.1 wt.% concentration with seawater. The nano-aided sweep efficiency was studied via IFT and imbibition tests, and by examining the displacement pressure behavior. Flooding tests indicated incremental oil recovery between 1.51 and 6.13% of the original oil in place (OOIP). The oil sweep efficiency was affected by the reduction in core’s permeability induced by the aggregation/agglomeration of NPs in the pores. Different types of mechanisms, such as reduction in IFT, generation of in-situ emulsion, microscopic flow diversion and alteration of wettability, together, can explain the nano-EOR effect. However, it was found that the change in the rock wettability to more water-wet condition seemed to govern the sweeping efficiency. These experimental results are valuable addition to the data bank on the application of novel NPs injection in porous media and aid to understand the EOR mechanisms associated with the application of polymer-coated silica nanoparticles.

scholarly journals The Investigation of Silica Nanoparticles-CO2 Foam Stability for Enhancing Oil Recovery Purpose

2020 ◽  
Vol 9 (1) ◽  
pp. 36-45
Author(s):  
David Maurich
Keyword(s):  
Silica Nanoparticles ◽  
Oil Recovery ◽  
Volume Ratio ◽  
Mobility Ratio ◽  
Phase Volume ◽  
Sweep Efficiency ◽  
Co2 Gas ◽  
Phase Volume Ratio ◽  
Co2 Foam ◽  
Brine Salinity

Carbon dioxide (CO2) gas injection is one of the most successful Enhanced Oil Recovery (EOR) methods. But the main problem that occurs in immiscible CO2 injection is the poor volumetric sweep efficiency which causes large quantities of the oil to be retained in pore spaces of reservoir. Although this problem can be improved through the injection of surfactant with CO2 gas where the surfactant will stabilize CO2 foam, this method still has some weaknesses due to foam size issue, surfactants compatibility problems with rocks and reservoir fluids and are less effective at high brine salinity and reservoir temperature such as typical oil reservoirs in Indonesia. This research aims to examine the stability of the foams/emulsions, compatibility and phase behavior of suspensions generated by hydrophobic silica nanoparticles on various salinity of formation water as well as to determine its effect on the mobility ratio parameter, which correlate indirectly with macroscopic sweep efficiency and oil recovery factor. This research utilizes density, static foam, and viscosity test which was carried out on various concentrations of silica nanoparticles, brine salinity and phase volume ratio to obtain a stable foam/emulsion design. The results showed that silica nanoparticles can increase the viscosity of displacing fluid by generating emulsions or foams so that it can reduce the mobility ratio toward favorable mobility, while the level of stability of the emulsion or foam of the silica nanoparticles suspension is strongly influenced by concentration, salinity and phase volume ratio. The high resistance factor of the emulsions/foams generated by silica nanoparticles will promote better potential of these particles in producing more oil.

Pore-Scale Transport Mechanisms and Macroscopic Displacement Effects of In-Situ Oil-in-Water Emulsions in Porous Media

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Chuan Lu ◽  
Wei Zhao ◽  
Yongge Liu ◽  
Xiaohu Dong
Keyword(s):  
Porous Media ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Mobility Control ◽  
Pore Scale ◽  
Sweep Efficiency ◽  
Emulsion Droplets ◽  
Oil In Water ◽  
Retention Volumes

Oil-in-water (O/W) emulsions are expected to be formed in the process of surfactant flooding for heavy oil reservoirs in order to strengthen the fluidity of heavy oil and enhance oil recovery. However, there is still a lack of detailed understanding of mechanisms and effects involved in the flow of O/W emulsions in porous media. In this study, a pore-scale transparent model packed with glass beads was first used to investigate the transport and retention mechanisms of in situ generated O/W emulsions. Then, a double-sandpack model with different permeabilities was used to further study the effect of in situ formed O/W emulsions on the improvement of sweep efficiency and oil recovery. The pore-scale visualization experiment presented an in situ emulsification process. The in situ formed O/W emulsions could absorb to the surface of pore-throats, and plug pore-throats through mechanisms of capture-plugging (by a single emulsion droplet) and superposition-plugging or annulus-plugging (by multiple emulsion droplets). The double-sandpack experiments proved that the in situ formed O/W emulsion droplets were beneficial for the mobility control in the high permeability sandpack and the oil recovery enhancement in the low permeability sandpack. The size distribution of the produced emulsions proved that larger pressures were capable to displace larger O/W emulsion droplets out of the pore-throat and reduce their retention volumes.

New In-situ Carbon Dioxide Generating Enhance Oil Recovery Technology

1999 ◽  
Author(s):  
I. S. Dzhafarov ◽  
S. V. Brezitsky ◽  
A. K. Shakhverdiev ◽  
G. M. Panakhov ◽  
B. A. Suleimanov
Keyword(s):  
Carbon Dioxide ◽  
Oil Recovery ◽  
Enhance Oil Recovery
Sign in / Sign up

Export Citation Format

Share Document