Impact of High Resolution 3D Geomechanics on Well Optimization in the Southern Gulf of Suez, Egypt

2021 ◽  
Author(s):  
Mohamed Elkhawaga ◽  
Wael A. Elghaney ◽  
Rajarajan Naidu ◽  
Assef Hussen ◽  
Ramy Rafaat ◽  
...  
Keyword(s):  
High Resolution ◽  
Pore Pressure ◽  
Cost Optimization ◽  
Oil Field ◽  
Wellbore Stability ◽  
Gulf Of Suez ◽  
Geomechanical Model ◽  
3D Geomechanical Model ◽  
The Cost ◽  
The Impact

Abstract Optimizing the number of casing strings has a direct impact on cost of drilling a well. The objective of the case study presented in this paper is the demonstration of reducing cost through integration of data. This paper shows the impact of high-resolution 3D geomechanical modeling on well cost optimization for the GS327 Oil field. The field is located in the Sothern Gulf of Suez basin and has been developed by 20 wells The conventional casing design in the field included three sections. In this mature field, especially with the challenge of reducing production cost, it is imperative to look for opportunites to optimize cost in drilling new wells to sustain ptoduction. 3D geomechanics is crucial for such cases in order to optimize the cost per barrel at the same time help to drill new wells safely. An old wellbore stability study did not support the decision-maker to merge any hole sections. However, there was not geomechanics-related problems recorded during the drilling the drilling of different mud weights. In this study, a 3D geomechanical model was developed and the new mud weight calculations positively affected the casing design for two new wells. The cost optimization will be useful for any future wells to be drilled in this area. This study documents how a 3D geomechanical model helped in the successful delivery of objectives (guided by an understanding of pore pressure and rock properties) through revision of mud weight window calculations that helped in optimizing the casing design and eliminate the need for an intermediate casing. This study reveals that the new calculated pore pressure in the GS327 field is predominantly hydrostatic with a minor decline in the reservoir pressure. In addition, rock strength of the shale is moderately high and nearly homogeneous, which helped in achieving a new casing design for the last two drilled wells in the field.

Influence of Rock Plastic Behavior on the Wellbore Stability

2021 ◽  
Author(s):  
Elena Grishko ◽  
Aboozar Garavand ◽  
Alexey Cheremisin
Keyword(s):  
Failure Criteria ◽  
Wellbore Stability ◽  
Standard Approach ◽  
Plastic Behavior ◽  
Element Formulation ◽  
Geomechanical Model ◽  
Plastic Properties ◽  
Plastic Deformations ◽  
3D Geomechanical Model

Abstract Currently, the standard approach to building a geomechanical model for analyzing wellbore stability involves taking into account only elastic deformations. This approach has shown its inconsistency in the design and drilling of wells passing through rocks with pronounced plastic properties. Such rocks are characterized by the fact that when the loads acting on them change, they demonstrate not only elastic, but also plastic (irreversible) deformations. Plastic deformations have an additional impact on the distribution of stresses in the rock of the near-wellbore zone on a qualitative and quantitative level. Since plastic deformations are not taken into account in the standard approach, in this case the results of the wellbore stability analysis are based on incorrectly calculated stresses acting in the rock. As a result, it can lead to misinterpretation of the model for analysis, suboptimal choice of trajectory, incorrect calculation of safe mud window and an incorrectly selected set of measures to reduce the risks of instability. The aim of this work is to demonstrate the advantages of the developed 3D elasto-plastic program for calculating the wellbore stability in comparison with the standard elastic method used in petroleum geomechanics. The central core of the work is the process of initialization of the elasto-plastic model according to the data of core tests and the subsequent validation of experimental and numerical loading curves. The developed 3D program is based on a modified Drucker-Prager model and implemented in a finite element formulation. 3D geomechanical model of wellbore stability allows describing deformation processes in the near-wellbore zone and includes the developed failure criteria. The paper shows a special approach to the determination of the mud window based on well logging data and core tests by taking into account the plastic behavior of rocks. An important result of this study is the determination of the possibility of expanding the mud window when taking into account the plastic criterion of rock failure.

Mechanical-Thermal-Chemical Coupled Research of Wellbore Stability in Jabung Oil Field, Indonesia

2011 ◽  
Vol 402 ◽  
pp. 709-714 ◽  
Author(s):  
Pei Yang ◽  
Mian Chen ◽  
Yan Jin ◽  
Bing Hou ◽  
Kang Qiu ◽  
...  
Keyword(s):  
Stress Distribution ◽  
Drilling Fluid ◽  
Great Influence ◽  
Chemical Properties ◽  
Oil Field ◽  
Wellbore Stability ◽  
Additional Stress ◽  
Borehole Stability ◽  
Well Trajectory ◽  
The Impact

The Jabung oilfield in Indonesia is characterized by complex geological structural movement, large tectonic stress and high temperature gradient. Accidents such as borehole collapse and sticking were frequently encountered when drilling shale formations, which often result in serious damage. In this paper, a series of experiments were conducted to evaluate the performance of shale in drilling fluid, including linear expansion rate evaluation tests and rolling recovery evaluation tests. Also X-ray diffraction was used to analyze the mineral composition of shale. The mechanical parameters of shale were obtained through statistical analysis. By using ABAQUS software, the temperature difference induced by thermal stress distribution was analyzed. After that, the borehole stress distribution was determined by coupling the additional stress with in-situ stress. Finally, based on borehole stability mechanical models, the effects of well trajectory on borehole stability were analyzed. We found that the chemical properties of drilling fluid, wellbore trajectory and temperature has a great influence on wellbore stability, and the impact of temperature changes and of well trajectory are the largest factor.

scholarly journals Operating cost analysis: sources and methods

2019 ◽  
pp. 132-138
Author(s):  
Nadiya Khorunzhak ◽  
Tetyana Portovaras
Keyword(s):  
Cost Optimization ◽  
Operating Cost ◽  
Operating Costs ◽  
Sources Of Information ◽  
Methods Of Analysis ◽  
External Sources ◽  
Internal Sources ◽  
Abc Analysis ◽  
The Cost ◽  
The Impact

Purpose. The aim of the article is identification of requirements and composition of sources of analysis, critical assessment of their information content, as well as emphasis on the application of a systematic approach to the analysis of operating costs and compliance of its method with these criteria. Methodology of research. The empirical research methods are used in the course of the research, in particular: analysis – in order to identify the composition of sources of analysis of operating expenses; generalization – to substantiate the classification of sources of analysis and to formulate recommendations on the choice of methods of analysis, which most fully allow to estimate the operating costs. Findings. The principles of formation of information base of the analysis of operating expenses are substantiated, which will allow to obtain high-quality information on their status and on the basis of the obtained results to predict the activity of the enterprise in the future. The study of the impact of factors on the analysis of operating expenses allowed us to distinguish sources of information into two groups: internal and external. It is determined that internal sources of data for analysis are accounting records, which are formed at enterprises, and which is considered by the authors as a source of analysis of operating expenses. External sources of information the authors consider all possible information resources of an external nature, research of the competitive environment and reporting of subjects with similar types of activity. Originality. The scheme of interconnection sources and analysis results of operations is proposed, which comprehensive utilization, will allow obtaining result analytical information on which management can optimize the cost of compliance with objectives and increase effectiveness of operations. According to modern realities, the most suitable methods of analysis are offered, which allow to adequately assessing the situation of the enterprise in the strategic plane with respect to operating expenses. Practical value. Carrying out an assessment of the operating costs of an enterprise with using various methods and tools of analysis in a complex provides obtaining unbiased data that can be effectively used for the purpose of cost optimization and increase of productivity. Key words: analysis; operating costs; cost optimization; internal sources of information; external sources of information; strategic methods; ABC analysis.

scholarly journals Construction of a 3d geomechanical model and its influence on the dynamic indicators of a carbonate reservoir model

2021 ◽  
Vol 3 (1) ◽  
pp. 43-55
Author(s):  
D. B. Abishev ◽  
V. V. Shishkin ◽  
I. G. Alekhin ◽  
A. Z. Nasibullin
Keyword(s):  
Hydrodynamic Model ◽  
Oil And Gas ◽  
Three Dimensional ◽  
Carbonate Reservoir ◽  
Oil Field ◽  
Gas Content ◽  
Property A ◽  
Geomechanical Model ◽  
History Match ◽  
3D Geomechanical Model

The article presents the process and results of constructing a three-dimensional geomechanical model of an oil field located in the eastern edge of the Caspian basin. Oil and gas content is established in carbonate deposits of the Lower and Middle Carboniferous. The model was based on well log data, one-dimensional geomechanical models and a 3D geological model. The result of geomechanical modeling is the obtained property of additional permeability of the critically loaded discrete fracture network, which was later used in the history match of the hydrodynamic model. In addition to the fracture property, a series of conductive faults were also identified during the history match. When carrying out geomechanical modeling, international experience was taken into account in the calculation of critically loaded fractures and their relationship with the intervals of inflow and loss in carbonate reservoirs. The updated hydrodynamic model, taking into account the geomechanical model, significantly improved the convergence of the model and historical indicators of bottomhole pressures.

A Geomechanical Model and Workflow for Calibrating Elastic Moduli and Min/Max Horizontal Stress from Well Logs in the Nahr Umr Shale

2021 ◽  
Author(s):  
Michael Alexander Shaver ◽  
Gilles Pierre Michel Segret ◽  
Denya Pratama Yudhia ◽  
Suhail Mohammed Al Ameri ◽  
Erwan Couziqou ◽  
...  
Keyword(s):  
Pore Pressure ◽  
Drilling Fluid ◽  
Well Logging ◽  
Wellbore Stability ◽  
Rock Properties ◽  
Lateral Strain ◽  
Fluid Density ◽  
Geomechanical Model ◽  
Stability Problems ◽  
Stress Models

Abstract Thin layering and micro-fracturing of the thin laminated layers are some possible reasons for the wellbore stability problems of the Nahr Umr shale. If the drilling fluid density is too low, collapsing of the borehole is possible, and if the drilling fluid density is too high, invasion of the shale can occur, weakening the shale, making boreholes prone to instability. These effects can be semi-quantified and assessed through the development of a geomechanical model. The application of a geomechanical model of a reservoir and overlaying formations can be very useful for addressing ways to select a sweet spot and optimize the completion and development of a reservoir. The geomechanical model also provides a sound basis for addressing unforeseen drilling and borehole stability problems that are encountered during the life cycle of a reservoir. Key components of any geomechanical model are the principal stresses at depth: overburden, minimum horizontal principle stress, and maximum horizontal principle stress. These determine the existing tectonic fault regime: normal, strike-slip, and reverse. Additional components of a geomechanical model are pore pressure, unconfined compressive strength (UCS) rock strength, tilted anisotropy, and fracture and faults from image logs and seismic. Unfortunately, models used to make continuous well logging depth-based stress predictions involve some parameters that are derived from laboratory tests, fracture injection tests, and the actual fracturing of a well—all contributing to the uncertainty of the model predictions. This paper addresses ways to obtain these key parameter components of the geomechanical model from well logging data calibrated to ancillary data. It is shown how stress, UCS, and pore pressure prediction and interpretation can be improved by developing and applying models using wellbore acoustic, triple combo, and borehole image data calibrated to laboratory and field measurements. The nahr umr shale and other organic mudstone formations exhibit vertical transverse isotropic (VTI) anisotropy in the sense that rock properties are different in the vertical and horizontal directions (assuming non-tilted flatbed layering), the horizontal acoustic velocity is different from that of vertical velocity. This necessitates the building of anisotropic moduli and stress models. The anisotropic stress models require lateral strain, which as shown in the paper, can be obtained from micro-frac tests and/or borehole breakout data.

scholarly journals Numerical Simulation of Geostress and Pore Pressure Evolution around Oil or Water Well under Different Injection-Production Ratio

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Liu Jian-jun ◽  
Yu Xian-bin ◽  
Zhao Jin-zhou
Keyword(s):  
Numerical Simulation ◽  
Pore Pressure ◽  
Oil And Gas ◽  
Dynamic Change ◽  
Gas Production ◽  
Oil Field ◽  
Wellbore Stability ◽  
Field Development ◽  
Production Ratio ◽  
Stress Changes

Geostress evolution in the process of oil field development can directly influence wellbore stability. Therefore, it is significant to strengthen the research of the evolution rule for well drilling and casing protection. Considering the interaction between reservoir seepage and stress fields, a mathematical model to characterize the stress evolution around wellbore was built. Using the FEM Software ABAQUS, through numerical simulation, the authors studied the evolution features of pore pressure and stress changes with time under different injection-production ratio, which disclosed the dynamic change regulation of pore pressure and stress of surrounding rock nearby the injection and production wells. These results may have implications in the treatment of wellbore stability and optimizing the injection and production processes during oil and gas production.

Numerical Modeling of Sand Production Potential Estimation and Passive Control Optimization: A Case Study

2018 ◽  
Author(s):  
Eva Lopez-Puiggene ◽  
Nubia Aurora Gonzalez-Molano ◽  
Jose Alvarellos-Iglesias ◽  
Jose M. Segura ◽  
M. R. Lakshmikantha
Keyword(s):  
Stress State ◽  
High Resolution ◽  
Plastic Strain ◽  
Pore Pressure ◽  
In Situ Stress ◽  
Point Of View ◽  
Wellbore Stability ◽  
Sand Production ◽  
Production Stress

Solids/sand production is an unintended byproduct of the hydrocarbon production that, from an operational point of view, might potentially lead to undesirable consequences. This paper focuses on a study centered in the geomechanical perspective for solids production. An integrated workflow is presented to analyze the combined effect of reservoir pore-pressure, drawdown, in-situ stress, rock properties and well/perforations orientation on the onset of solid production. This workflow incorporates analyses at multiple scales: rock constitutive modeling at lab scale, 1D geomechanical models at wellbore scale along well trajectories, a 3D geomechanical model at the reservoir scale and 3D/4D high resolution reservoir - geomechanical coupled models at the well and perforation scale. 1D geomechanical models were built using log and field data, drilling experience and laboratory tests in order to characterize in situ stresses, pore pressure and rock mechanics properties (stiffness and strength) profiles for several wells. Rock shear failure mechanism was also analyzed in order to build a pre-drill model and evaluate the wellbore stability from a geomechanical point of view. Pre-production stress modeling was simulated to obtain a representative initial stress state integrating 1D geomechanics well results, 3D dynamic model and seismic interpretations. Mechanical properties were distributed considering properties calculated in the 1D geomechanical models as input. 3D stress field was validated with in-situ stress profiles from 1D modeling results. This simulated pre-production stress state was then used as an initial condition for the reservoir - geomechanical coupled simulations. Effective stress changes and deformations associated to pore pressure changes were calculated including the coupling between reservoir and geomechanical modeling. Finally, a 3D/4D high resolution well scale reservoir - geomechanical coupled numerical model was built in order to determine the threshold of sand production. A limit of plastic strain was obtained based on numerical simulations of available production data, DST and ATWC tests. This critical plastic strain limit was used as a criterion (strain-based) for rock failure to define the onset of sand production as a function of pore pressure, perforation orientation and rock strength. Conclusions regarding the perforation orientations related to the possibility of producing solids can support operational decisions in order to avoid undesirable solid production and therefore optimize the production facilities capacity and design to handle large amounts of solids and/or the clogging of the well.

scholarly journals Anisotropic Wellbore Stability Analysis: Impact on Failure Prediction

2020 ◽  
Author(s):  
Michinori Asaka ◽  
Rune Martin Holt
Keyword(s):  
Stability Analysis ◽  
Pore Pressure ◽  
Elastic Anisotropy ◽  
Wellbore Stability ◽  
Practical Implementation ◽  
Borehole Stability ◽  
Gas Field ◽  
Drilling Operations ◽  
Failure Predictions ◽  
The Impact

Abstract Shale formations are the main source of borehole stability problems during drilling operations. Suboptimal predictions of borehole failure may partly be caused by neglecting the anisotropic nature of shales: Conventional wellbore stability analysis is based on borehole stresses computed from isotropic linear elasticity (Kirsch solution) with the assumption of no induced pore pressure. This is very convenient for a practical implementation but does not always work for shales. Here, anisotropic wellbore stability analysis was performed targeting an offshore gas field to investigate in particular the impact of elastic anisotropy on borehole failure predictions. Stress concentration around a circular borehole in anisotropic shale was calculated by the Amadei solutions, and induced pore pressure was obtained from the Skempton parameters based on anisotropic poroelasticity. Borehole failure regions and modes were then predicted using the effective stresses and those are apparently consistent with observations. A comparison with the conventional approach suggests the importance of accounting for elastic anisotropy: Predicted failure regions, modes, and also the associated mud weight limits can be completely different. This observation may have significant implications for other fields since shale often show strong elastic anisotropy.

scholarly journals Geomechanical Analysis for Deep Shale Gas Exploration Wells in the NDNR Blocks, Sichuan Basin, Southwest China

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1117 ◽  
Author(s):  
Majia Zheng ◽  
Hongming Tang ◽  
Hu Li ◽  
Jian Zheng ◽  
Cui Jing
Keyword(s):  
Pore Pressure ◽  
Shale Gas ◽  
Sichuan Basin ◽  
In Situ Stress ◽  
Wellbore Stability ◽  
Geomechanical Model ◽  
Stress Regime ◽  
Xujiahe Formation ◽  
Geomechanical Analysis

The abundant reserve of shale gas in Sichuan Basin has become a significant natural gas component in China. To achieve efficient development of shale gas, it is necessary to analyze the stress state, pore pressure, and reservoir mechanical properties such that an accurate geomechanical model can be established. In this paper, Six wells of Neijiang-Dazu and North Rongchang (NDNR) Block were thoroughly investigated to establish the geomechanical model for the study area. The well log analysis was performed to derive the in-situ stresses and pore pressure while the stress polygon was applied to constrain the value of the maximum horizontal principal stress. Image and caliper data, mini-frac test and laboratory rock mechanics test results were used to calibrate the geomechanical model. The model was further validated by comparing the model prediction against the actual wellbore failure observed in the field. It was found that it is associated with the strike-slip (SS) stress regime; the orientation of SHmax was inferred to be 106–130° N. The pore pressure appears to be approximately hydrostatic from the surface to 1000 m true vertical depth (TVD), but then becomes over-pressured from the Xujiahe formation. The geomechanical model can provide guidance for the subsequent drilling and completion in this area and be used to effectively avoid complex drilling events such as collapse, kick, and lost circulation (mud losses) along the entire well. Also, the in-situ stress and pore pressure database can be used to analyze wellbore stability issues as well as help design hydraulic fracturing operations.

Sign in / Sign up

Export Citation Format

Share Document