Modelling of Calcite Deposition on Geothermal Well Inflow Performance

2020 ◽  
Author(s):  
Seyed Mousa Mousavi Mirkalaei ◽  
Mark Douglas Edmondson ◽  
Anjani Kumar
Keyword(s):  
Geothermal Well ◽  
Calcite Deposition ◽  
Inflow Performance

The effect of calcite deposition on geothermal well inflow performance

Geothermics ◽  
1999 ◽  
Vol 28 (3) ◽  
pp. 425-444 ◽  
Author(s):  
Abdurrahman Satman ◽  
Zuleyha Ugur ◽  
Mustafa Onur
Keyword(s):  
Geothermal Well ◽  
Calcite Deposition ◽  
Inflow Performance

Acid-resistant polydimethylsiloxane additive for geothermal well cement in 150°C H2SO4solution

2003 ◽  
Vol 15 (1) ◽  
pp. 35-44 ◽  
Author(s):  
T. Sugama ◽  
L. E. Brothers ◽  
L. Weber
Keyword(s):  
Geothermal Well ◽  
Well Cement

A Model for a Geothermal Well in a Hydraulic Groundwater Flow for Ground Source Heat Pump Systems

2011 ◽  
Author(s):  
Kevin D. Woods ◽  
Alfonso Ortega
Keyword(s):  
Thermal Conductivity ◽  
Analytical Solution ◽  
Groundwater Flow ◽  
Heat Pump ◽  
Temperature Response ◽  
Ambient Air ◽  
Heat Pumps ◽  
Thermal Reservoir ◽  
Geothermal Well ◽  
Ground Source

Heat pumps are mechanical systems that provide heating to a space in the winter, and cooling in the summer. They are increasingly popular because the same system provides both cooling modes, depending on the direction of the cycle upon which they operate. For proper operation, the heat pump must be connected to a constant temperature thermal reservoir which in traditional systems is the ambient air. In ground source heat pumps however, subterranean ground water is used as the thermal reservoir. To access the subterranean groundwater, “geothermal” wells are drilled into the formation. Water from the building heating or cooling system is circulated through the wells thereby promoting heat exchange between the coolant water and the subterranean formation. The potential for higher efficiency heating and cooling has increased the utilization of ground source heating ventilating and air conditioning systems. In addition, their compatibility with a naturally occurring and stable thermal reservoir has increased their use in the design of sustainable or green buildings and man-made environments. Groundwater flow affects the temperature response of thermal wells due to advection of heat by physical movement of groundwater through the aquifer. Research on this subject is scarce in the geothermal literature. This paper presents the derivation of an analytical solution for thermal dispersion by conduction and advection from hydraulic groundwater flow for a “geothermal” well. This analytical solution is validated against asymptotic analytical solutions. The traditional constant linear heat source solution is dependent on the ground formation thermal properties; the most dominant of which is the thermal conductivity. The results show that as hydraulic groundwater flow increases, the influence of the ground formation thermal conductivity on the temperature response of the well diminishes. The diminishing influence is evident in the Peclet number parameter; a comparison of thermal advection from hydraulic groundwater flow to thermal conduction by molecular diffusion.

Effect of Non-Uniform Formation Damage on the Inflow Performance of Horizontal Wells.

1999 ◽  
Author(s):  
Habib Menouar ◽  
Abdulaziz Al-Majed ◽  
Syed Sajid Hasan
Keyword(s):  
Horizontal Wells ◽  
Formation Damage ◽  
Inflow Performance

Oil and Gas Drilling Optimization Technologies Applied Successfully to Unconventional Geothermal Well Drilling

2021 ◽  
Author(s):  
Junichi Sugiura ◽  
Ramon Lopez ◽  
Francisco Borjas ◽  
Steve Jones ◽  
John McLennan ◽  
...  
Keyword(s):  
Geothermal Energy ◽  
Oil And Gas ◽  
Optimization Techniques ◽  
Geothermal System ◽  
Well Drilling ◽  
Geothermal Well ◽  
Gas Drilling ◽  
Drilling Tools ◽  
Drilling Optimization ◽  
Oil And Gas Drilling

Abstract Geothermal energy is used in more than 20 countries worldwide and is a clean, reliable, and relatively available energy source. Nevertheless, to make geothermal energy available anywhere in the world, technical and economic challenges need to be addressed. Drilling especially is a technical challenge and comprises a significant part of the geothermal development cost. An enhanced geothermal system (EGS) is a commercially viable thermal reservoir where two wells are interconnected by some form of hydraulic stimulation. In a commercial setting, fluid is injected into this hot rock and passes between wells through a network of natural and induced fractures to transport heat to the surface system for electricity generation. To construct EGS wells, vertical and directional drilling is necessary with purpose-built drilling and steering equipment. This is an application where oil-and-gas drilling tools and techniques can be applied. A recent well, 16A(78)-32, drilled as part of the US Department of Energy's (DOE's) Utah Frontier Observatory for Research in Geothermal Energy (FORGE) program, highlights some of the technical challenges, which include drilling an accurate vertical section, a curve section, and a 5300-ft 65° tangent section in a hard granitic formation at temperatures up to 450°F (232°C). Extensive downhole temperature simulations were performed to select fit-for-purpose drilling equipment such as purely mechanical vertical drilling tools, instrumented steerable downhole motors, measurement-while-drilling (MWD) tools, and embedded high-frequency drilling dynamics recorders. Downhole and surface drilling dynamics data were used to fine- tune bit design and motor power section selection and continuously improve the durability of equipment, drilling efficiency, and footage drilled. Drilling optimization techniques used in oil and gas settings were successfully applied to this well, including analysis of data from drilling dynamics sensors embedded in the steerable motors and vertical drilling tools, surface surveillance of mechanical specific energy (MSE), and adopting a drilling parameter roadmap to improve drilling efficiency to minimize drilling dysfunctions and equipment damages. Through drilling optimization practices, the instrumented steerable motors with proper bit selections were able to drill more than 40 ft/hr on average, doubling the rate of penetration (ROP), footage, and run length experienced in previous granite wells. This paper presents a case study in which cutting-edge oil-and-gas drilling technologies were successfully applied to reduce the geothermal well drilling time by approximately half.

Sign in / Sign up

Export Citation Format

Share Document