Can the Viscoelasticity of HPAM Polymer Solution Make the Polymer Flooding Compete with Gel Treatment to Improve Sweep Efficiency? A Comparison with Different Polymer Gel Systems

2019 ◽  
Author(s):  
Tariq K Khamees ◽  
Ralph E Flori
Keyword(s):  
Polymer Solution ◽  
Polymer Flooding ◽  
Polymer Gel ◽  
Sweep Efficiency ◽  
Gel Treatment

Field Implementation of In-Depth Conformance Gel Treatment Prior to Starting an ASP Flooding Pilot

2021 ◽  
Author(s):  
Mohammed T. Al-Murayri ◽  
Abrahim Hassan ◽  
Naser Alajmi ◽  
Jimmy Nesbit ◽  
Bastien Thery ◽  
...  
Keyword(s):  
Polymer Solution ◽  
Injection Pressure ◽  
High Viscosity ◽  
Production Well ◽  
Sweep Efficiency ◽  
Injection Wells ◽  
Appreciable Change ◽  
Well Pattern ◽  
Gel Treatment ◽  
Viscosity Polymer

Abstract Mature carbonate reservoirs under waterflood in Kuwait suffer from relatively low oil recovery due to poor volumetric sweep efficiency, both areal, vertically, and microscopically. An Alkaline-Surfactant-Polymer (ASP) pilot using a regular five-spot well pattern is in progress targeting the Sabriyah Mauddud (SAMA) reservoir in pursuit of reserves growth and production sustainability. SAMA suffers from reservoir heterogeneities mainly associated with permeability contrast which may be improved with a conformance treatment to de-risk pre-mature breakthrough of water and chemical EOR agents in preparation for subsequent ASP injection and to improve reservoir contact by the injected fluids. Each of the four injection wells in the SAMA ASP pilot was treated with a chemical conformance improvement formulation. A high viscosity polymer solution (HVPS) of 200 cP was injected prior to a gelant formulation consisting of P300 polymer and X1050 crosslinker. After a shut-in period, wells were then returned to water injection. Injection of high viscosity polymer solution (HVPS) at the four injection wells showed no increase in injection pressure and occurred higher than expected injection rates. Early breakthrough of polymer was observed at SA-0561 production well from three of the four injection wells. No appreciable change in oil cut was observed. HVPS did not improve volumetric sweep efficiency based on the injection and production data. Gel treatment to improve the volumetric conformance of the four injection wells resulted in all the injection wells showing increased of injection pressure from approximately 3000 psi to 3600 psi while injecting at a constant rate of approximately 2,000 bb/day/well. Injection profiles from each of the injection well ILTs showed increased injection into lower-capacity zones and decreased injection into high-capacity zones. Inter-well tracer testing showed delayed tracer breakthrough at the center SA-0561 production well from each of the four injection wells after gel placement. SA-0561 produced average daily produced temperature increased from approximately 40°C to over 50°C. SA-0561 oil cuts increased up to almost 12% from negligible oil sheen prior to gel treatments. Gel treatment improved volumetric sweep efficiency in the SAMA SAP pilot area.

Experimental Study of Microgel Conformance-Control Treatment for a Polymer-Flooding Reservoir Containing Superpermeable Channels

SPE Journal ◽  
2021 ◽  
pp. 1-13
Author(s):  
Yang Zhao ◽  
Jianqiao Leng ◽  
Baihua Lin ◽  
Mingzhen Wei ◽  
Baojun Bai
Keyword(s):  
Polymer Solution ◽  
Oil Recovery ◽  
Polymer Flooding ◽  
Control Treatment ◽  
Void Space ◽  
Sweep Efficiency ◽  
Microgel Particles ◽  
Water Cut ◽  
Preformed Particle Gels ◽  
Bypassed Oil

SummaryPolymer flooding has been widely used to improve oil recovery. However, its effectiveness would be diminished when channels (e.g., fractures, fracture-like channels, void-space conduits) are present in a reservoir. In this study, we designed a series of particular sandwich-like channel models and tested the effectiveness and applicable conditions of micrometer-sized preformed particle gels (PPGs, or microgels) in improving the polymer-flooding efficiency. We studied the selective penetration and placement of the microgel particles, and their abilities for fluid diversion and oil-recovery improvement. The results suggest that polymer flooding alone would be inefficient to achieve a satisfactory oil recovery as the heterogeneity of the reservoir becomes more serious (e.g., permeability contrast kc/km > 50). The polymer solution would vainly flow through the channels and leave the majority of oil in the matrices behind. Additional conformance-treatment efforts are required. We tried to inject microgels in an attempt to shut off the channels. After the microgel treatment, impressive improvement of the polymer-flooding performance was observed in some of our experiments. The water cut could be reduced significantly by as high as nearly 40%, and the sweep efficiency and overall oil recovery of the polymer flood were improved. The conditions under which the microgel-treatment strategy was effective were further explored. We observed that the microgels form an external impermeable cake at the very beginning of microgel injection and prevent the gel particles from entering the matrices. Instead, the microgel particles could selectively penetrate and shut off the superpermeable channels under proper conditions. Our results suggest that the 260-µm microgel particles tested in this study are effective to attack the excessive-water-production problem and improve the oil recovery when the channel has a high permeability (>50 darcies). The gels are unlikely to be effective for channels that are less than 30 darcies because of the penetration/transport difficulties. After the gels effectively penetrate and shut off the superpermeable channel, the subsequent polymer solution is diverted to the matrices (i.e., the unswept oil zones) to displace the bypassed oil. Overall, this study provides important insights to help achieve successful polymer-flooding applications in reservoirs with superpermeable channels.

scholarly journals Evaluation of Polymer Alternating Waterflooding in Multilayered Heterogeneous Waterflooded Reservoir

2018 ◽  
Vol 171 ◽  
pp. 04001
Author(s):  
Warut Tuncharoen ◽  
Falan Srisuriyachai
Keyword(s):  
Numerical Simulation ◽  
Viscous Fluid ◽  
Polymer Solution ◽  
Oil Recovery ◽  
High Viscosity ◽  
Polymer Flooding ◽  
Operating Parameters ◽  
Sweep Efficiency ◽  
Polymer Injection ◽  
Water Breakthrough

Polymer flooding is widely implemented to improve oil recovery since polymer can increase sweep efficiency and smoothen heterogeneous reservoir profile. However, polymer solution is somewhat difficult to be injected due to high viscosity and thus, water slug is recommended to be injected before and during polymer injection in order to increase an ease of injecting this viscous fluid into the wellbore. In this study, numerical simulation is performed to determine the most appropriate operating parameters to maximize oil recovery. The results show that pre-flushed water should be injected until water breakthrough while alternating water slug size should be as low as 5% of polymer slug size. Concentration for each polymer slugs should be kept constant and recommended number of alternative cycles is 2. Combining these operating parameters altogether contributes to oil recovery of 53.69% whereas single-slug polymer flooding provides only 53.04% which is equivalent to 8,000 STB of oil gain.

Large-Volume Foam-Gel Treatments to Improve Conformance of the Rangely CO2 Flood

1999 ◽  
Vol 2 (01) ◽  
pp. 14-24 ◽  
Author(s):  
T.L. Hughes ◽  
F. Friedmann ◽  
D. Johnson ◽  
G.P. Hild ◽  
A. Wilson ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Large Volume ◽  
Fractured Reservoirs ◽  
Gas Injection ◽  
Cost Effective ◽  
Fracture Network ◽  
Polymer Gel ◽  
Sweep Efficiency ◽  
Gel Treatment ◽  
Incremental Oil Recovery

Summary Large-volume foam-gel treatments can provide a cost-effective method to achieve in-depth conformance improvement in fractured reservoirs. The applicability and cost effectiveness of the approach depends on the availability of a cheap source of gas, the efficiency with which the foam can be placed into the high permeability thief zone(s), and the effectiveness of the gelled foam barrier in diverting reservoir drive fluids to improve oil recovery. This paper reviews progress in the application of large-volume CO2-foam-gel treatments to improve conformance in the Rangely Weber Sand Unit (RWSU), Colorado. During the period November 1996-November 1997 three large-volume foam-gel treatments were successfully placed into the Rangely reservoir. The first 36?400 bbl treatment, implemented November 1996, increased the pattern oil rate from 260 barrels of oil per day (BOPD) in March 1997 to ±330 BOPD in August 1998; a conservative estimate of incremental oil recovery is ±40?000 bbl by the end of August 1998. The second 43?450 bbl treatment, implemented August-September 1997, increased the pattern oil rate from ±430 BOPD in March 1998 to ±470 BOPD in August 1998; post-treatment, the pattern oil rate data is described by a linear regression with slope, +56 BOPD but it is too early to make a firm estimate of incremental oil recovery. The third 44?700 bbl treatment, implemented October-November 1997, increased the pattern oil rate from ±330 BOPD in May 1998 to ±375 BOPD in July-August 1998; a linear regression of the post-treatment data gives a positive slope but again it is too early to estimate incremental oil recovery. Some general features in the pattern production response given by the three foam-gel treatments were observed. First, each of the treatments induces a stabilization in the pattern oil rate which, for treatments I and II, is accompanied by a decrease in the pattern gas rate. Second, the first positive oil rate response given by each of the treatments is observed 6-8 months after treatment execution and is dominated by the response at producer wells lying to the west/southwest and/or east/southeast of the treated injector well. For a given treatment volume, the cost of a foam-gel treatment at Rangely is 40%-50% below the average cost of polymer gel treatments. As the foam is injected at a higher rate, the total pump time required for a 40?000 bbl foam-gel treatment is similar to a 20?000 bbl polymer gel treatment. Early during pumping treatments II and III, we attempted to increase the CO2 content of the foam from 80 to 85 vol?%; this resulted in a wellhead pressure which was too close to the CO2 pressure limit necessitating a decrease in foam injection rate. Thus, in optimizing foam-gel treatment cost, there is a balance between maximizing the content of the inexpensive CO2 phase and minimizing total pump time. For Treatments II and III, the cost of the liquid phase formulation was reduced by decreasing the concentrations of surfactant and buffer. The implementation and evaluation of three large-volume foam-gel treatments at Rangely indicates that the foam-gel approach provides a cost-effective method to achieve in-depth conformance improvement in fractured reservoirs. Introduction A recent survey1 indicated that the proportion of U.S. EOR production recovered by gas injection has increased from 18% to 41% during the period 1986-1996. A major contribution to this trend has been the strong increase in the number of miscible carbon dioxide (CO2) projects which now account for > 70% of the total number of ongoing gas injection projects in the U.S. The Rangely CO2 flood began in 1986; currently, there are 372 active producer wells and 300 active injector wells, 259 of which are injecting CO2 using the water-alternating-gas (WAG) process. In the application of gas injection to heterogeneous reservoirs, oil recovery efficiency can be limited by poor conformance as an increasing proportion of the injected gas flows through higher permeability thief zones and/or fractures. The importance of conformance improvement has long been recognized at Rangely. The main problem being addressed is poor CO2 conformance due to preferential flow through the natural fracture network leading to premature gas breakthrough at the associated producers. This process increases operating costs and reduces oil recovery. The objective of the Rangely Conformance Improvement Team (CIT) is to improve conformance in order to reduce operating costs and increase the oil recovery to >1 billion bbl (>50% OOIP) compared to the current 815 million bbl (43% OOIP). A number of mechanical methods and chemical treatments have been employed to improve conformance at Rangely. While dual injection strings and selective injection equipment (SIE) have been used for improved injection profile control, chemical treatments using polymer gels2 and CO2 foam3 have been used to improve volumetric sweep efficiency and oil recovery. During the period 1994-1997, 49 injector wells were treated by placing a MARCIT™ gel4 into the fracture network.5 While these treatments have improved local sweep efficiency and oil recovery, economics limit the maximum treatment volume per injector well to 15?000-20?000 bbl. Certain regions of the Rangely reservoir require considerably larger treatment volumes to reduce the permeability of a larger volume of the fracture network and improve conformance in a larger volume of the well pattern.

scholarly journals NEW AQUEOUS POLYMER FOR HIGH-TEMPERATURE RESERVOIRS

2018 ◽  
Vol 15 (30) ◽  
pp. 380-386
Author(s):  
Y. V. SAVINYKH ◽  
L. D. LANG
Keyword(s):  
High Temperature ◽  
Oil Recovery ◽  
High Salinity ◽  
Sea Water ◽  
Polymer Flooding ◽  
Water Soluble ◽  
Water Flooding ◽  
Polymer Gel ◽  
Sweep Efficiency ◽  
Water Soluble Polymer

Polymer flooding is technologically simple and highly effective method of enhanced oil recovery. The method is based on adding a small amount of polymer in conventional water flooding of oil reservoirs. The increase in viscosity and the reduction of the mobility of injected water are to equalize the displacement front by slowing the moving of water in the highly permeable zones and restricting the formation of water finger. These factors help to increase the sweep efficiency and oil-water displacement efficiency during flooding. Polymer flooding has been used successfully in clastic and carbonate reservoirs, as well as in low-permeability reservoirs such as a fractured basement. However, most of the current polymer gel used for control water flows are decayed by a high content of ions Ca2+ and Mg2+ in formation water or in injected water. Similarly, polymer gels lose their stability at high reservoir temperature (above 70°C). Developing water-soluble polymer, which does not change their rheological properties under high salinity and high temperature (over 100°C), is very important when producing offshore, where sea water is commonly used for flooding (high salinity of 30-40 g/L).

EFFECT OF ORIENTATION OF STRATA ON MACROSCOPIC SWEEP EFFICIENCY OF WATER/POLYMER FLOODING IN LAYERED POROUS MEDIA

2011 ◽  
Vol 14 (9) ◽  
pp. 761-776 ◽  
Author(s):  
Hamid Emami Meybodi ◽  
Riyaz Kharrat ◽  
Benyamin Yadali Jamaloei
Keyword(s):  
Porous Media ◽  
Polymer Flooding ◽  
Sweep Efficiency ◽  
Layered Porous Media

Development of a Polymer Gel System for Improved Sweep Efficiency and Injection Profile Modification of IOR/EOR Treatments

2014 ◽  
Author(s):  
Freddy Crespo ◽  
B. R. Reddy ◽  
Larry Eoff ◽  
Christopher Lewis ◽  
Natalie Pascarella
Keyword(s):  
Polymer Gel ◽  
Sweep Efficiency ◽  
Profile Modification ◽  
Gel System

Assessment on the Transport of Polymeric Solution through High-Salinity Reservoirs Containing Divalent Cations

2013 ◽  
Vol 807-809 ◽  
pp. 2607-2611
Author(s):  
Byung In Choi ◽  
Moon Sik Jeong ◽  
Kun Sang Lee
Keyword(s):  
Quantitative Assessment ◽  
High Salinity ◽  
Divalent Cations ◽  
Polymer Concentration ◽  
Field Application ◽  
Polymer Flooding ◽  
Sweep Efficiency ◽  
Chemical Theory ◽  
Bottom Hole ◽  
Reservoir Conditions

Water salinity and hardness have been regarded as main limitation for field application of polymer floods. It causes not only reduction of polymer concentration, but also injectivity loss in the near wellbore. Based on the mathematical and chemical theory, extensive numerical simulations were conducted to investigate performance of polymer floods in the high-salinity reservoirs. According to results from simulations, the high salinity reduces the viscosity of polymer in contacting area. That causes a poor sweep efficiency of polymer flooding. Moreover, the presence of divalent cations makes the project of polymer flooding worse. That is because of excessively increased bottom-hole pressure in injection well by the precipitation of polymer. The quantitative assessment of polymer floods needs to be required before field application. Therefore, the results in this paper are helpful for optimal polymer flooding design under harsh reservoir conditions.

Sign in / Sign up

Export Citation Format

Share Document