Improving Hole Cleaning Efficiency using Nanosilica in Water-Based Drilling Mud

2018 ◽  
Author(s):  
Afeez O. Gbadamosi ◽  
Radzuan Junin ◽  
Jeffrey O. Oseh ◽  
Augustine Agi ◽  
Nurudeen Yekeen ◽  
...  
Keyword(s):  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Water Based

scholarly journals Comparative Analysis of the Effect of Barite and Hematite on the Rheology of Water-Based Drilling Mud

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Osei H
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Attrition Rate ◽  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Drilling Operation ◽  
Water Based ◽  
Petroleum Resources ◽  
Drilling Muds ◽  
The Impact

High demand for oil and gas has led to exploration of more petroleum resources even at remote areas. The petroleum resources are found in deeper subsurface formations and drilling into such formations requires a well-designed drilling mud with suitable rheological properties in order to avoid or reduce associated drilling problems. This is because rheological properties of drilling muds have considerable effect on the drilling operation and cleaning of the wellbore. Mud engineers therefore use mud additives to influence the properties and functions of the drilling fluid to obtain the desired drilling mud properties especially rheological properties. This study investigated and compared the impact of barite and hematite as weighting agents for water-based drilling muds and their influence on the rheology. Water-based muds of different concentrations of weighting agents (5%, 10%, 15% and 20% of the total weight of the drilling mud) were prepared and their rheological properties determined at an ambient temperature of 24ᵒC to check their impact on drilling operation. The results found hematite to produce higher mud density, plastic viscosity, gel strength and yield point when compared to barite at the same weighting concentrations. The higher performance of the hematite-based muds might be attributed to it having higher specific gravity, better particle distribution and lower particle attrition rate and more importantly being free from contaminants. The water-based muds with hematite will therefore be more promising drilling muds with higher drilling and hole cleaning efficiency than those having barite.

scholarly journals The effect of drill–pipe rotation on improving hole cleaning using polypropylene beads in water-based mud at different hole angles

2019 ◽  
Vol 10 (3) ◽  
pp. 1253-1262 ◽  
Author(s):  
A. Katende ◽  
B. Segar ◽  
I. Ismail ◽  
F. Sagala ◽  
H. H. A. R. Saadiah ◽  
...  
Keyword(s):  
Buoyancy Force ◽  
Drilling Fluid ◽  
Drill Pipe ◽  
Drilling Mud ◽  
Hole Cleaning ◽  
Drag Forces ◽  
Water Based ◽  
Drilling Operations ◽  
Cost Efficient ◽  
Pipe Rotation

AbstractHole cleaning is always a problem, particularly during drilling operations, and drilling fluid plays an important role in transporting drill cuttings through an annular section of wellbore to the surface. To transport the cuttings, a water-based mud with added polypropylene beads was selected since it is environmentally friendly and cost efficient. The polypropylene beads help to transport cuttings by providing an additional buoyancy force that lifts the cuttings to the surface via the influence of collision and drag forces. This experiment was performed using a 20 ft test section, 10 ppg drilling mud and 0.86 m/s annular velocity in a laboratory scale rig simulator, and the concentration of polypropylene beads was varied from 0 to 8 ppb. As the concentration of polypropylene increases, the cutting transport ratio also increases. It was observed that the fewest cuttings are lifted at a critical angle of 60°, followed by 45°, 30°, 90° and 0°. Additionally, cutting sizes had moderate effects on the cutting lifting efficiency, where smaller cutting sizes (0.5–1.0 mm) are easier to lift than larger cutting sizes (2.0–2.8 mm). Furthermore, a study of buoyancy force and impulsive force was conducted to investigate the cutting lifting efficiencies of various concentrations of polypropylene beads. This lifting capacity was also assisted by the presence of polyanionic cellulose (PAC), which increases the mud carrying capacity and is effective for smaller cuttings. The results show that in the presence of pipe rotation, the cutting lifting efficiency is slightly enhanced due to the orbital motion provided by the drill pipe for better hole cleaning. In conclusion, polypropylene beads combined with pipe rotation increase the cutting transport ratio in the wellbore.

scholarly journals Experimental Study for Assessment of Cutting Density Effect on Hole Cleaning Efficiency in Inclined and Horizontal Wells

2020 ◽  
Vol 21 (3) ◽  
pp. 1-8
Author(s):  
Sahmi E Mohammed ◽  
Faleh H. M. Almahdawi
Keyword(s):  
Yield Point ◽  
Flow Rate ◽  
Inclination Angle ◽  
Horizontal Wells ◽  
Medium Size ◽  
Drilling Mud ◽  
Flow Loop ◽  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Constant Flow Rate

The poor hole cleaning efficiency could causes many problems such as high torque, drag, poor hydraulics and pipe stuck. These inherent problems result in an avoidable high operation cost which this study tried to address.  In this study, the effect of cutting density on hole cleaning efficiency in deviated and horizontal wells was investigated. Experiments were conducted using 40 feet (12 m) long of flow loop made from iron and PVC. However, the test section was made from PVC with (5.1m) long and (4” ID) for outer pipe and (2” OD) inner pipe. The cutting transport ratio (CTR) was determined from weight measurements for each test. Cutting Transport Ratio has been investigated for effects of the following parameters; flow rate, cutting size and density, yield point of drilling mud, and inclination angle. Once the setup was positioned at the desired inclination, the cutting was transported for 3 minutes at a constant flow rate and yield point. The amount of cutting removed during each test was thereafter weighted to determine cutting transport ratio CTR. The results obtained from this study showed that the cutting density has a slight to moderate effect on hole cleaning efficiency. Also, there was a remarkable improvement in the cutting transport ratio annular velocity and hole inclination angle was increased. However, the yield point (Yp) was negligible at maximum values of annular velocity. Therefore, at high value of yield point the cuttings with large and medium size were transported more than small size. This case is inversed at a low value of Yp. Moreover, for all sizes the heavy cutting transport less than light cutting. Finally, the critical angle was recorded between 65o-75o. Sigma plot 12.5 program has been used to graph all figures in this paper.

Enhancement lubricity properties of water-based mud with nanoparticles

2020 ◽  
pp. 70-74
Author(s):  
V.V. Guliyev ◽  
◽  
◽  
Keyword(s):  
Yield Point ◽  
Coefficient Of Friction ◽  
Drilling Fluid ◽  
Research Work ◽  
Shear Thinning ◽  
Rheological Parameters ◽  
Drilling Process ◽  
Drilling Mud ◽  
Pseudoplastic Fluid ◽  
Water Based

Currently, a great number of drilling fluids with different additives are used all over the world. Such additives are applied to control the properties of the drilling mud. The main purpose for controlling is to achieve more effective and safe drilling process. This research work aims to develop Water-Based Mud (WBM) with a Coefficient of Friction (CoF) as low as Oil-Based Mud (OBM) and better rheological properties. As it is known, produced CoF by WBM is higher than OBM, which means high friction between wellbore or casing and drill string. It was the reason for studying the effect of nanosilica on drilling fluid properties such as lubricity, rheological parameters and filtrate loss volume of drilling mud. The procedures were carried out following API RP 13B and API 13I standards. Five concentrations of nanosilica were selected to be tested. According to the results obtained, it was defined that adding nanosilica into the mud decreases CoF of basic WBM by 26 % and justifies nanosilica as a good lubricating agent for drilling fluid. The decreasing trend in coefficient of friction and plastic viscosity for nanosilica was obtained until the concentration of 0.1 %. This reduction is due to the shear thinning or pseudoplastic fluid behavior. After 0.1 %, an increase at PV value trend indicates that it does not follow shear thinning behavior and after reaching a certain amount of dissolved solids in the mud, it acts like normal drilling fluid. The yield point of the mud containing nanoparticles was higher than the basic one. Moreover, a growth in the concentration leads to an increase in yield point value. The improvement of this fluid system cleaning capacity via hydraulics modification and wellhole stability by filter cake endurance increase by adding nanosilica is shown as well. The average well construction data of “Neft Dashlary” field was used for the simulation studies conducted for the investigation of hydraulics parameters of reviewed fluids for all series of experiments. The test results were accepted reliable in case of at least 3 times repeatability.

Hole-Cleaning Fibers Improve Cuttings-Carrying Capacity

2021 ◽  
Vol 73 (05) ◽  
pp. 63-64
Author(s):  
Chris Carpenter
Keyword(s):  
Flow Regime ◽  
Carrying Capacity ◽  
Rheological Model ◽  
Drilling Fluid ◽  
Test Method ◽  
Abu Dhabi ◽  
Rheological Parameters ◽  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Drilling Operations

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper SPE 203147, “Investigating Hole-Cleaning Fibers’ Mechanism To Improve Cutting Carrying Capacity and Comparing Their Effectiveness With Common Polymeric Pills,” by Mohammad Saeed Karimi Rad, Mojtaba Kalhor Mohammadi, SPE, and Kourosh Tahmasbi Nowtarki, International Drilling Fluids, prepared for the 2020 Abu Dhabi International Petroleum Exhibition and Conference, Abu Dhabi, held virtually 9–12 November. The paper has not been peer reviewed. Hole cleaning in deviated wells is more challenging than in vertical wells because of the boycott effect or the eccentricity of the drillpipe. Poor hole cleaning can result in problems such as borehole packoff or excessive equivalent circulating density. The complete paper investigates a specialized fibrous material (Fiber 1) for hole-cleaning characteristics. The primary goal is to identify significant mechanisms of hole-cleaning fibers and their merits compared with polymeric high-viscosity pills. Hole-Cleaning Indices Based on a review of the literature, most effective parameters regarding hole cleaning in different well types were investigated. These parameters can be classified into the following five categories: - Well design (e.g., hole angle, drillpipe eccentricity, well trajectory) - Drilling-fluid properties (e.g., gel strength, mud weight) - Formation properties (e.g., lithology, cutting specific gravity, cuttings size and shape) - Hydraulic optimizations (e.g., flow regime, nozzle size, number of nozzles) - Drilling practices (e.g., drillpipe rotation speed, wellbore tortuosity, bit type, rate of penetration, pump rate) In this research, rheological parameters and parameters of the Herschel-Bulkley rheological model are considered to be optimization inputs to increase hole-cleaning efficiency of commonly used pills in drilling operations. The complete paper offers a detailed discussion of both the importance of flow regime and the role of the Herschel-Bulkley rheological model in reaching a better prognosis of drilling-fluid behavior at low shear rates. The properties of the fibrous hole-cleaning agent used in the complete paper are provided in Table 1. Test Method Two series of tests were performed. The medium of the first series is drilling water, with the goal of evaluating the efficiency of Fiber 1 in fresh pills. The second series of tests was per-formed with a simple polymeric mud as a medium common in drilling operations. Formulations and rheological properties of both test series are provided in Tables 4 and 5 of the complete paper, respectively.

Full Scale Flow Loop Experiments of Hole Cleaning Performances of Drilling Fluids

2015 ◽  
Author(s):  
Jan David Ytrehus ◽  
Ali Taghipour ◽  
Sneha Sayindla ◽  
Bjørnar Lund ◽  
Benjamin Werner ◽  
...  
Keyword(s):  
Test Section ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Flow Loop ◽  
Base Oil ◽  
Hole Cleaning ◽  
Cleaning Performance ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Cost

One important requirement for a drilling fluid is the ability to transport the cuttings out of the borehole. Improved hole cleaning is a key to solve several challenges in the drilling industry and will allow both longer wells and improved quality of well construction. It has been observed, however, that drilling fluids with similar properties according to the API standard can have significantly different behavior with respect to hole cleaning performance. The reasons for this are not fully understood. This paper presents results from flow loop laboratory tests without and with injected cuttings size particles using a base oil and a commercial oil based drilling fluid. The results demonstrate the importance of the rheological properties of the fluids for the hole cleaning performance. A thorough investigation of the viscoelastic properties of the fluids was performed with a Fann viscometer and a Paar-Physica rheometer, and was used to interpret the results from the flow loop experiments. Improved understanding of the fluid properties relevant to hole cleaning performance will help develop better models of wellbore hydraulics used in planning of well operations. Eventually this may lead to higher ROP with water based drilling fluids as obtained with oil based drilling fluids. This may ease cuttings handling in many operations and thereby significantly reduce the drilling cost using (normally) more environmentally friendly fluids. The experiments have been conducted as part of an industry-sponsored research project where understanding the hole cleaning performance of various oil and water based drilling fluids is the aim. The experiments have been performed under realistic conditions. The flow loop includes a 10 meter long test section with 2″ OD freely rotating drillstring inside a 4″ ID wellbore made of concrete. Sand particles were injected while circulating the drilling fluid through the test section in horizontal position.

Sign in / Sign up

Export Citation Format

Share Document