Solids Loading Assessment for Produced Water Reinjection in a Carbonate Reservoir

Author(s):  
Peng Chen ◽  
Thomas Willingham ◽  
Alunood Al Sowaidi ◽  
Dragan Stojkovic ◽  
James Brown
2021 ◽  
Author(s):  
Robert Zagitov ◽  
Jaisankar Subramanian ◽  
Srinivasa Rao Gopisetty ◽  
Avinash Kumar ◽  
Vinay Mathur ◽  
...  

Abstract Severe fouling of crude oil and produced water treatment equipment of Mangala Processing Terminal (MPT) with elastic deposits has been observed after EOR polymer breaking through to the producing wells. Fouling by polymer containing solids caused the system bottlenecking impacting on crude production rates and deterioration of water quality for injection due to increase of total solids loading. The objective of the study included developing the water treatment technology for removing the returned polymer, developing the pilot run for implementation of the technology and scaling up the process if the pilot shows success. Crude processed at MPT is produced from Mangala, Bhagyam and Aishwarya fields which are located at the north-west part of India. Full field polymer flooding has been implemented in the Mangala field from 2015. Fouling of downhole and topside equipment with elastic deposits has been reported soon after polymer breakthrough the same year. For reducing the fouling potential and solids loading, the concept of removing the returned polymer from produced water has been considered as beneficial. Removal of polymer through the chemical coagulation was considered for developing. Extensive laboratory and bench testing have been carried out. Based on the laboratory results, the pilot was developed and carried out on the flotation equipment available at MPT. In the laboratory and bench test for polymer coagulation, over 70% polymer removal was achieved with non-sticky flocks and minimal sludge. The tests also demonstrated reduced suspended solids, residual oil and filterability improvement of treated water. The pilot run confirmed effectiveness of the chemical coagulation process to remove polymer. Polymer removal > 70% was observed during the pilot. Oil removal from produced water at 60-80% was seen. Cloud point of polymer remaining in water increased from 60°C to > 110°C indicating on the significant potential reduction of remaining polymer to precipitate from treated water. The pilot results demonstrated on the applicability of the technology of chemical polymer removal at MPT and will be used for scaling up the treatment facilities.


2017 ◽  
Author(s):  
Peng Chen ◽  
Thomas Willingham ◽  
Timothy Ian Morrow ◽  
Alunood K. Al Sowaidi ◽  
Dragan Stojkovic ◽  
...  

2021 ◽  
Author(s):  
Paulo Henrique de Amorim Martins ◽  
Bruno Marins Freiman

Abstract The aim of this paper is to present the results obtained by the use of fresh water in order to remove inorganic scale deposited inside production tubing from carbonate reservoir deepwater production wells with high salinity and low BS&W. The paper covers the entire process from the identification of production loss, the investigation of its main causes, treatment propositions and discussion of obtained results. One of the hypotheses regarding the scale deposition mechanism in the studied wells is that the precipitation of salts is due to the evaporation of produced water. This phenomenon occurs through the contact of water with dry gas applied in the artificial elevation method (gas lift). The proposed and tested scale removal procedure consists of a soaking of the production tubing with fresh water in order to dissolve the deposition or at least part of it that is soluble in water. Preventive care actions in relation to flow assurance were taken, since the suggested method uses a high volume of fresh water, increasing the hydrate risks. Scaling in wells with those characteristics was systematically removed through remote acidification (with specialized vessel assistance). That approach has shown to be always effective. On the other hand, remote acidification was always costly and dependent on the availability of critical resources. The technique depicted in this paper requires neither a vessel nor acid and, therefore, incurs significantly lower costs. The results obtained in the first tests were substantially positive since the wells’ productivity was fully restored. In this sense, the hypothesis of water solubility of the scale deposition was confirmed, and the method validated. Since its validation, the method has been applied a number of times, confirming its repeatability, and extending its use to other wells with similar scaling occurrences, reducing costs and restoring the production in a short time. Nevertheless, new challenges arise in relation to the full comprehension of the deposited material and the prevention of its deposition.


KURVATEK ◽  
2017 ◽  
Vol 1 (2) ◽  
pp. 21-31
Author(s):  
Fatimah Miharno

ABSTRACT*Zefara* Field formation Baturaja on South Sumatra Basin is a reservoir carbonate and prospective gas. Data used in this research were 3D seismik data, well logs, and geological information. According to geological report known that hidrocarbon traps in research area were limestone lithological layer as stratigraphical trap and faulted anticline as structural trap. The study restricted in effort to make a hydrocarbon accumulation and a potential carbonate reservoir area maps with seismic attribute. All of the data used in this study are 3D seismic data set, well-log data and check-shot data. The result of the analysis are compared to the result derived from log data calculation as a control analysis. Hydrocarbon prospect area generated from seismic attribute and are divided into three compartments. The seismic attribute analysis using RMS amplitude method and instantaneous frequency is very effective to determine hydrocarbon accumulation in *Zefara* field, because low amplitude from Baturaja reservoir. Low amplitude hints low AI, determined high porosity and high hydrocarbon contact (HC).  Keyword: Baturaja Formation, RMS amplitude seismic attribute, instantaneous frequency seismic attribute


CIM Journal ◽  
2018 ◽  
Vol 9 (4) ◽  
pp. 195-214
Author(s):  
G. J. Simandl ◽  
C. Akam ◽  
M. Yakimoski ◽  
D. Richardson ◽  
A. Teucher ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document