scholarly journals A New Approach to Polymer Flooding: Effects of Early Polymer Injection and Wettability on Final Oil Recovery

SPE Journal ◽  
2018 ◽  
Vol 24 (01) ◽  
pp. 129-139 ◽  
Author(s):  
J. L. Juárez-Morejón ◽  
H.. Bertin ◽  
A.. Omari ◽  
G.. Hamon ◽  
C.. Cottin ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Phase Distribution ◽  
Water Saturation ◽  
Dominant Role ◽  
Polymer Flooding ◽  
Displacement Efficiency ◽  
Sweep Efficiency ◽  
Two Phase ◽  
Polymer Injection ◽  
The Core

Summary An experimental study of polymer flooding is presented here, focusing on the influence of initial core wettability and flood maturity (volume of water injected before polymer injection) on final oil recovery. Experiments were performed using homogeneous Bentheimer Sandstone samples of similar properties. The cores were oilflooded using mineral oil for water-wet conditions and crude oil (after an aging period) for intermediate-wet conditions; the viscosity ratio between oil and polymer was kept constant in all experiments. Polymer, which is a partially hydrolyzed polyacrylamide (HPAM), was used at a concentration of 2,500 ppm in a moderate-salinity brine. The polymer solution was injected in the core at different waterflood-maturity times [breakthrough (BT) and 0, 1, 1.75, 2.5, 4, and 6.5 pore volumes (PV)]. Coreflood results show that the maturity of polymer injection plays an important role in final oil recovery, regardless of wettability. The waterflood-maturity time 0 PV (polymer injection without initial waterflooding) leads to the best sweep efficiency, whereas final oil production decreases when the polymer-flood maturity is high (late polymer injection after waterflooding). A difference of 15% in recovery is observed between early polymer flooding (0 PV) and late maturity (6.5 PV). Concerning the effect of wettability, the recovery factor obtained with water-wet cores is always lower (from 10 to 20%, depending on maturity) than the values obtained with intermediate-wet cores, raising the importance of correctly restoring core wettability to obtain representative values of polymer incremental recovery. The influence of wettability can be explained by the oil-phase distribution at the pore scale. Considering that the waterflooding period leads to different values of the oil saturation at which polymer flooding starts, we measured the core dispersivity using a tracer method at different states. The two-phase dispersivity decreases when water saturation increases, which is favorable for polymer sweep. This study shows that in addition to wettability, the maturity of polymer flooding plays a dominant role in oil-displacement efficiency. Final recovery is correlated to the dispersion value at which polymer flooding starts. The highest oil recovery is obtained when the polymer is injected early.

scholarly journals Laboratory Study on EOR in Offshore Oilfields by Variable Concentrations Polymer Flooding

2017 ◽  
Vol 10 (1) ◽  
pp. 94-107 ◽  
Author(s):  
Kaoping Song ◽  
Ning Sun ◽  
Yanfu Pi
Keyword(s):  
Oil Recovery ◽  
Field Application ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Displacement Efficiency ◽  
Constant Concentration ◽  
Sweep Efficiency ◽  
Displacement Effect ◽  
Fracture Pressure ◽  
Recovery Technique

Background: Polymer flooding is the most commonly applied chemical enhanced-oil-recovery technique in offshore oilfields. However, there are challenges and risks in applying the technology of polymer flooding to offshore heavy oil development. Objective: This paper compared the spread law and the displacement effect of different injection modes and validated the feasibility of enhancing oil recovery by variable concentrations polymer flooding. Method: Two types of laboratory experiments were designed by using micro etching glass models and heterogeneous artificial cores. Furthermore, in order to determine a better polymer flooding mode, the displacement results, displacement characteristic curves and oil saturation distribution of heterogeneous artificial cores were also compared, respectively. Results: The experimental results showed that the recovery of variable concentrations polymer flooding was higher than that of constant concentration polymer flooding, under conditions of same total amount of polymer and similar water flooding recovery. Its sweep efficiency and displacement efficiency were also significantly higher than those of constant concentration polymer flooding. Moreover, variable concentrations polymer flooding had lower peak pressure and was at lower risk for reaching the formation fracture pressure. Conclusion: As a consequence, variable concentrations polymer flooding has certain feasibility for heterogeneous reservoir in offshore oilfields, and can improve interlayer heterogeneity to further tapping remaining oil in medium and low permeability layer. Conclusions of this paper can provide reference for the field application of polymer flooding in offshore oilfields.

Laboratory Investigations of Factors Influencing Polymer Flood Performance

1975 ◽  
Vol 15 (04) ◽  
pp. 338-346 ◽  
Author(s):  
M.T. Szabo
Keyword(s):  
Oil Recovery ◽  
Polymer Solutions ◽  
Polymer Concentration ◽  
Polymer Flooding ◽  
Mobility Control ◽  
Sweep Efficiency ◽  
Experimental Conditions ◽  
Polymer Injection ◽  
Polymer Flood

Abstract Numerous polymer floods were performed in unconsolidated sand packs using a C14-tagged, cross-linked, partially hydrolyzed ployacrylamide, and the data are compared with brine-flood performance in the same sands. performance in the same sands. The amount of "polymer oil" was linearly proportional to polymer concentration up to a proportional to polymer concentration up to a limiting value. The upper limit of polymer concentration yielding additional polymer oil was considerably higher for a high-permeability sand than for a low-permeability sand. It is shown that a minimum polymer concentration exists, below which no appreciable polymer oil can be produced in high-permeability sands. The effect of polymer slug size on oil recovery is shown for various polymer concentrations, and the results from these tests are used to determine the optimum slug size and polymer concentration for different sands. The effect of salinity was studied by using brine and tap water during polymer floods under similar conditions. Decreased salinity resulted in improved oil recovery at low, polymer concentrations, but it had little effect at higher polymer concentrations. Polymer injection that was started at an advanced stage of brine flood also improved the oil recovery in single-layered sand packs. Experimental data are presented showing the effect of polymer concentration and salinity on polymer-flood performance in stratified reservoir polymer-flood performance in stratified reservoir models. Polymer concentrations in the produced water were measured by analyzing the radioactivity of effluent samples, and the amounts of retained polymer in the stratified models are given for each polymer in the stratified models are given for each experiment. Introduction In the early 1960's, a new technique using dilute polymer solutions to increase oil recovery was polymer solutions to increase oil recovery was introduced in secondary oil-recovery operations. Since then, this new technique has attained wide-spread commercial application. The success and the complexity of this new technology has induced many authors to investigate many aspects of this flooding technique. Laboratory and field studies, along with numerical simulation of polymer flooding, clearly demonstrated that polymer additives increase oil recovery. polymer additives increase oil recovery. Some of the laboratory results have shown that applying polymers in waterflooding reduces the residual oil saturation through an improvement in microscopic sweep efficiency. Other laboratory studies have shown that applying polymer solutions improves the sweep efficiency in polymer solutions improves the sweep efficiency in heterogeneous systems. Numerical simulation of polymer flooding, and a summary of 56 field applications, clearly showed that polymer injection initiated at an early stage of waterflooding is more efficient than when initiated at an advanced stage. Although much useful information has been presented, the experimental conditions were so presented, the experimental conditions were so variable that difficulties arose in correlating the numerical data. So, despite this good data, a systematic laboratory study of the factors influencing the performance of polymer flooding was still lacking in the literature. The purpose of this study was to investigate the effect of polymer concentration, polymer slug size, salinity in the polymer bank, initial water saturation, and permeability on the performance of polymer floods. The role of oil viscosity did not constitute a subject of this investigation. However, some of the data indicated that the applied polymer resulted in added recovery when displacing more viscous oil. The linear polymer-flood tests were coupled with tests in stratified systems, consisting of the same sand materials used in linear flood tests. Thus, it was possible to differentiate between the role of polymer in mobility control behind the flood front in each layer and its role in mobility control in the entire stratified system through improvement in vertical sweep efficiency. A radioactive, C14-tagged hydrolyzed polyacrylamide was used in all oil-recovery tests. polyacrylamide was used in all oil-recovery tests. SPEJ P. 338

scholarly journals Investigation of an Improved Polymer Flooding Scheme by Compositionally-Tuned Slugs

Processes ◽  
2020 ◽  
Vol 8 (2) ◽  
pp. 197 ◽  
Author(s):  
Ryan Santoso ◽  
Victor Torrealba ◽  
Hussein Hoteit
Keyword(s):  
Oil Recovery ◽  
Polymer Flooding ◽  
Solution Viscosity ◽  
Design Parameters ◽  
High Concentration ◽  
Sweep Efficiency ◽  
Polymer Injection ◽  
Low Salinity ◽  
Injection Scheme ◽  
Vertical Heterogeneity

Polymer flooding is an effective enhanced oil recovery technology used to reduce the mobility ratio and improve sweep efficiency. A new polymer injection scheme is investigated that relies on the cyclical injection of low-salinity, low-concentration polymer slugs chased by high-salinity, high-concentration polymer slugs. The effectiveness of the process is a function of several reservoir and design parameters related to polymer type, concentration, salinity, and reservoir heterogeneity. We use reservoir simulations and design-of-experiments (DoE) to investigate the effectiveness of the proposed polymer injection scheme. We show how key objective functions, such as recovery factor and injectivity, are impacted by the reservoir and design parameters. In this study, simulations showed that the new slug-based process was always superior to the reference polymer injection scheme using the traditional continuous injection scheme. Our results show that the process is most effective when the polymer weight is high, corresponding to large inaccessible pore-volumes, which enhances polymer acceleration. High vertical heterogeneity typically reduces the process performance because of increased mixing in the reservoir. The significance of this process is that it allows for increased polymer solution viscosity in the reservoir without increasing the total mass of polymer, and without impairing polymer injectivity at the well.

scholarly journals Evaluation of Polymer Alternating Waterflooding in Multilayered Heterogeneous Waterflooded Reservoir

2018 ◽  
Vol 171 ◽  
pp. 04001
Author(s):  
Warut Tuncharoen ◽  
Falan Srisuriyachai
Keyword(s):  
Numerical Simulation ◽  
Viscous Fluid ◽  
Polymer Solution ◽  
Oil Recovery ◽  
High Viscosity ◽  
Polymer Flooding ◽  
Operating Parameters ◽  
Sweep Efficiency ◽  
Polymer Injection ◽  
Water Breakthrough

Polymer flooding is widely implemented to improve oil recovery since polymer can increase sweep efficiency and smoothen heterogeneous reservoir profile. However, polymer solution is somewhat difficult to be injected due to high viscosity and thus, water slug is recommended to be injected before and during polymer injection in order to increase an ease of injecting this viscous fluid into the wellbore. In this study, numerical simulation is performed to determine the most appropriate operating parameters to maximize oil recovery. The results show that pre-flushed water should be injected until water breakthrough while alternating water slug size should be as low as 5% of polymer slug size. Concentration for each polymer slugs should be kept constant and recommended number of alternative cycles is 2. Combining these operating parameters altogether contributes to oil recovery of 53.69% whereas single-slug polymer flooding provides only 53.04% which is equivalent to 8,000 STB of oil gain.

scholarly journals Investigation of Injection Strategy of Branched-Preformed Particle Gel/Polymer/Surfactant for Enhanced Oil Recovery after Polymer Flooding in Heterogeneous Reservoirs

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1950 ◽  
Author(s):  
Hong He ◽  
Jingyu Fu ◽  
Baofeng Hou ◽  
Fuqing Yuan ◽  
Lanlei Guo ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Large Scale ◽  
Oil Prices ◽  
Polymer Flooding ◽  
Displacement Efficiency ◽  
Sweep Efficiency ◽  
Injection Strategy ◽  
Simultaneous Injection ◽  
Heterogeneous Reservoirs ◽  
Incremental Oil Recovery

The heterogeneous phase combination flooding (HPCF) system which is composed of a branched-preformed particle gel (B-PPG), polymer, and surfactant has been proposed to enhance oil recovery after polymer flooding in heterogeneous reservoirs by mobility control and reducing oil–water interfacial tension. However, the high cost of chemicals can make this process economically challenging in an era of low oil prices. Thus, in an era of low oil prices, it is becoming even more essential to optimize the heterogeneous phase combination flooding design. In order to optimize the HPCF process, the injection strategy has been designed such that the incremental oil recovery can be maximized using the corresponding combination of the B-PPG, polymer, and surfactant, thereby ensuring a more economically-viable recovery process. Different HPCF injection strategies including simultaneous injection and alternation injection were investigated by conducting parallel sand pack flooding experiments and large-scale plate sand pack flooding experiments. Results show that based on the flow rate ratio, the pressure rising area and the incremental oil recovery, no matter whether the injection strategy is simultaneous injection or alternation injection of HPCF, the HPCF can significantly block high permeability zone, increase the sweep efficiency and oil displacement efficiency, and effectively improve oil recovery. Compared with the simultaneous injection mode, the alternation injection of HPCF can show better sweep efficiency and oil displacement efficiency. Moreover, when the slug of HPCF and polymer/surfactant with the equivalent economical cost is injected by alternation injection mode, as the alternating cycle increases, the incremental oil recovery increases. The remaining oil distribution at different flooding stages investigated by conducting large-scale plate sand pack flooding experiments shows that alternation injection of HPCF can recover more remaining oil in the low permeability zone than simultaneous injection. Hence, these findings could provide the guidance for developing the injection strategy of HPCF to further enhance oil recovery after polymer flooding in heterogeneous reservoirs in the era of low oil prices.

scholarly journals Influence of Sulfate Ions on the Combined Application of Modified Water and Polymer Flooding—Rheology and Oil Recovery

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2356 ◽  
Author(s):  
Muhammad Tahir ◽  
Rafael E. Hincapie ◽  
Leonhard Ganzer
Keyword(s):  
Oil Recovery ◽  
Sodium Sulfate ◽  
Water Injection ◽  
Polymer Flooding ◽  
Two Phase ◽  
Sulfate Ions ◽  
Polymer Injection ◽  
Smart Water ◽  
Combined Application ◽  
Core Flood

Oil recovery using modified/smart water technology can be maximized by optimizing the composition of the injected water. Brine optimization is also believed to improve polymer flooding performance. This chapter assesses and defines the potential impact of combining low-salt-modified water with polymer flooding, based on the presence of sulfate in the injection water. Hence, we evaluated the influence of sodium sulfate on (1) polymer viscoelasticity, under the assumption that the phenomena exists, and (2) oil recovery and pressure response. Mainly, a comprehensive rheological evaluation and two-phase core flood experiments are the focus of this work. Composition of injection brine is optimized after having synthetic seawater as a base brine. Core-flood experiments were performed in a secondary, tertiary and a sort of post-tertiary (quaternary) mode to evaluate the feasibility of applying both processes (modified water and polymer flood). Obtained data was subsequently cross-analyzed and as an overall observation, sodium sulfate helped with improving polymer viscosity compared to sodium chloride or divalent cation presence. Moreover, optimized modified water, with the higher amount of sulfate ions, showed an additional oil recovery in both secondary and tertiary mode of about 5.0%. Additionally, polymer injection in tertiary mode, after modified-water injection, showed significant additional oil recovery.

scholarly journals Experimental Study on Medium Viscosity Oil Displacement Using Viscoelastic Polymer

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Huiying Zhong ◽  
Qiuyuan Zang ◽  
Hongjun Yin ◽  
Huifen Xia
Keyword(s):  
Oil Recovery ◽  
Polymer Flooding ◽  
Water Soluble ◽  
Water Flooding ◽  
Bohai Bay ◽  
Residual Oil ◽  
Displacement Efficiency ◽  
Sweep Efficiency ◽  
Oil Displacement ◽  
Medium Viscosity

With the growing demand for oil energy and a decrease in the recoverable reserves of conventional oil, the development of viscous oil, bitumen, and shale oil is playing an important role in the oil industry. Bohai Bay in China is an offshore oilfield that was developed through polymer flooding process. This study investigated the pore-scale displacement of medium viscosity oil by hydrophobically associating water-soluble polymers and purely viscous glycerin solutions. The role and contribution of elasticity on medium oil recovery were revealed and determined. Comparing the residual oil distribution after polymer flooding with that after glycerin flooding at a dead end, the results showed that the residual oil interface exhibited an asymmetrical “U” shape owing to the elasticity behavior of the polymer. This phenomenon revealed the key of elasticity enhancing oil recovery. Comparing the results of polymer flooding with that of glycerin flooding at different water flooding sweep efficiency levels, it was shown that the ratio of elastic contribution on the oil displacement efficiency increased as the water flooding sweep efficiency decreased. Additionally, the experiments on polymers, glycerin solutions, and brines displacement medium viscosity oil based on a constant pressure gradient at the core scale were carried out. The results indicated that the elasticity of the polymer can further reduce the saturation of medium viscosity oil with the same number of capillaries. In this study, the elasticity effect on the medium viscosity oil interface and the elasticity contribution on the medium viscosity oil were specified and clarified. The results of this study are promising with regard to the design and optimum polymers applied in an oilfield and to an improvement in the recovery of medium viscosity oil.

scholarly journals Adaptive study on polymer flooding of secondary reservoir and infilling uniform

2018 ◽  
Vol 175 ◽  
pp. 01006
Author(s):  
Xu WenBo
Keyword(s):  
Oil Recovery ◽  
Physical Simulation ◽  
Injection Pressure ◽  
Leading Edge ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Monitoring Methods ◽  
Sweep Efficiency ◽  
Plane Sweep ◽  
Polymer Injection

For the main polymer flooding oilfield expansion and infill wells three times the area of deployment, the proposed development mode II oil reservoir of polymer flooding and thin and poor combination of three encryption. In this paper, the use of leading edge water monitoring methods and principles of the plane heterogeneity through physical simulation to study the effects of different mining methods II oil and a combination of the three encryption effects of flooding. Studies have shown that, together with the water flooding recovery can be increased by nearly 19 percent, higher than the water poly alternate drive about 4%, the injection pressure is about three types of reservoir 0.3MPa, flat stage water flood sweep efficiency compared with an average of 30.95%. Meanwhile polymer injection can increase oil recovery by 21%, but the limited ability of three types of oil injection, polymer injection pressure during injection 0.22PV up to 0.8MPa, water flooding stage by an average of 30 percent compared to the plane sweep efficiency. The water flooding recovery poly alternately raise only 15%, an average increase of 26.95 percent driven phase plane sweep efficiency than water. Theoretical results of this study may provide a reliable basis for the future development of efficient thin and poor reservoirs.

How Viscoelastic-Polymer Flooding Enhances Displacement Efficiency

SPE Journal ◽  
2016 ◽  
Vol 21 (03) ◽  
pp. 0675-0687 ◽  
Author(s):  
A.. Clarke ◽  
A. M. Howe ◽  
J.. Mitchell ◽  
J.. Staniland ◽  
L. A. Hawkes
Keyword(s):  
Oil Recovery ◽  
Capillary Number ◽  
Polymer Solutions ◽  
Underlying Mechanism ◽  
Polymer Flooding ◽  
Solution Viscosity ◽  
Flow Profile ◽  
Displacement Efficiency ◽  
Sweep Efficiency ◽  
Viscoelastic Polymer

Summary Increasing flooding-solution viscosity with polymers provides a favorable mobility ratio compared with brine flooding and hence improves volumetric sweep efficiency. Flooding with a polymer solution exhibiting elastic properties has been reported to increase displacement efficiency, resulting in a sustained doubling of the recovery enhancement compared with the use of conventional viscous-polymer flooding (Wang et al. 2011). Flooding with viscoelastic-polymer solutions is claimed also to increase recovery more than expected from changes in capillary number alone (Wang et al. 2010). This increase in displacement efficiency by viscoelastic polymers is reported to occur because of changes in the steady-state-flow profile and enhancements in oil stripping and thread formation. However, within the industry there are doubts that a genuine effect is observed, or that improvements in displacement efficiency occur with field-applicable flow regimes (Vermolen et al. 2014). In this study, we demonstrate that flooding with viscoelastic-polymer solutions can indeed increase recovery more than expected from changes in capillary number. We show a mechanism of fluctuations in flow at low Reynolds number by which viscoelastic-polymer solutions provide improvements in displacement efficiency. The mechanism, known as elastic turbulence, is an effect previously unrecognized in this context. We demonstrate that the effect may be obtained at field-relevant flow rates. Furthermore, this underlying mechanism explains both the enhanced capillary-desaturation curves and the observation of apparent flow thickening (Delshad et al. 2008; Seright et al. 2011) for these viscoelastic solutions in porous media. The work contrasts experiments on flow and recovery by use of viscous and viscoelastic-polymer solutions. The circumstances under which viscoelasticity is beneficial are demonstrated. The findings are applicable to the design of formulations for enhanced oil recovery (EOR) by polymer flooding. A combination of coreflooding, micromodel flow, and rheometric studies is presented. The results include single-phase and multiphase floods in sandstone cores. Polymer solutions are viscoelastic [partially hydrolyzed polyacrylamide (HPAM)] or viscous (xanthan). The effects of molecular weight, flow rate, and concentration of the HPAMs are described. The data lead us to suggest a mechanism that may be used to explain the observations of improved displacement efficiency and why the improvement is not seen for all viscoelastic-polymer floods.

Pore-Scale Investigation of Phase Distribution and Residual-Oil Development During Secondary and Tertiary Solvent Injection

2014 ◽  
Vol 18 (01) ◽  
pp. 39-52 ◽  
Author(s):  
Yousef Hamedi Shokrlu ◽  
Tayfun Babadagli
Keyword(s):  
Oil Recovery ◽  
Phase Distribution ◽  
Water Saturation ◽  
Hot Water ◽  
Experimental Investigations ◽  
Residual Oil ◽  
Displacement Efficiency ◽  
Oil Viscosity ◽  
Flow Process ◽  
Water Solvent

Summary Flow of three phases, of which one is miscible with another, in porous media may commonly be encountered during enhanced-oil-recovery (EOR) applications in oil reservoirs. Typical examples include solvent (miscible-gas) injection alternated with water and coinjection or alternate injection of steam (or hot water) and solvent in heavy-oil/bitumen reservoirs. Oil, water, and solvent flow together under immiscible (water/oil and water/solvent) and miscible (oil/solvent) conditions at the same time, and the distribution of phases and removal of residual oil in those types of processes depend on many parameters. This paper reports microscale experimental investigations on this complex flow process and provides an extensive parametric analysis on the microscopic displacement efficiency of oil recovery using miscible solvent. For this purpose, micromodels created by use of a replica of sandstones were used. Waterflood residual-oil displacement requires contact of the injected solvent with the blocked oil. The efficiency of this process depends on several parameters, including matrix wettability, oil viscosity, initial water saturation, and reservoir heterogeneity. On the other hand, the sequence of injection of solvent and water is considered as another parameter by which oil recovery can be affected significantly. The results of the micromodel-visualization experiments showed that injection of solvent before the introduction of any water to the reservoir can increase the recovery factor significantly. Existence of the water phase in the reservoir creates capillary barriers that prevent oil/solvent contact. The matrix wettability and oil viscosity were observed to be critically important to the amount of oil recovery.

Sign in / Sign up

Export Citation Format

Share Document