A Study of Gravity Counterflow Segregation

1962 ◽  
Vol 2 (02) ◽  
pp. 185-193 ◽  
Author(s):  
E.E. Templeton ◽  
R.F. Nielsen ◽  
C.D. Stahl

Abstract It has been customary, in predicting saturation changes, to use the Leverett "fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counterflow with which to test the theory. A 4-ft sandpacked tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, after which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. Introduction The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. Field and laboratory data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. It has been customary to use fractional flow rates instead of actual flow rates in displacement calculations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et al, and by Fayers and Sheldon, actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty. SPEJ P. 185^

SPE Journal ◽  
2019 ◽  
Vol 25 (01) ◽  
pp. 451-464 ◽  
Author(s):  
Swej Y. Shah ◽  
Herru As Syukri ◽  
Karl-Heinz Wolf ◽  
Rashidah M. Pilus ◽  
William R. Rossen

Summary Foam reduces gas mobility and can help improve sweep efficiency in an enhanced-oil-recovery (EOR) process. For the latter, long-distance foam propagation is crucial. In porous media, strong foam generation requires that the local pressure gradient exceed a critical value (▿Pmin). Normally, this happens only in the near-well region. Away from wells, these requirements might not be met, and foam propagation is uncertain. It has been shown theoretically that foam can be generated, independent of pressure gradient, during flow across an abrupt increase in permeability (Rossen 1999). The objective of this study is to validate theoretical explanations through experimental evidence and to quantify the effect of fractional flow on this process. This article is an extension of a recent study (Shah et al. 2018) investigating the effect of permeability contrast on this process. In this study, the effects of fractional flow and total superficial velocity are described. Coreflood experiments were performed in a cylindrical sintered-glass porous medium with two homogeneous layers and a sharp permeability jump in between, representing a lamination or cross lamination. Unlike previous studies of this foam-generation mechanism, in this study, gas and surfactant solution were coinjected at field-like velocities into a medium that was first flooded to steady state with gas/brine coinjection. The pressure gradient is measured across several sections of the core. X-ray computed tomography (CT) is used to generate dynamic phase-saturation maps as foam generates and propagates through the core. We investigate the effects of velocity and injected-gas fractional flow on foam generation and mobilization by systematically changing these variables through multiple experiments. The core is thoroughly cleaned after each experiment to remove any trapped gas and to ensure no hysteresis. Local pressure measurements and CT-based saturation maps confirm that foam is generated at the permeability transition, and it then propagates downstream to the outlet of the core. A significant reduction in gas mobility is observed, even at low superficial velocities. Foam was generated in all cases, at all the injected conditions tested; however, at the lowest velocity tested, strong foam did not propagate all the way to the outlet of the core. Although foam generation was triggered across the permeability boundary at this velocity, it appeared that, for our system, the limit of foam propagation, in terms of a minimum-driving-force requirement, was reached at this low rate. CT images were used to quantify the accumulation of liquid near the permeability jump, causing local capillary pressure to fall below the critical capillary pressure required for snap-off. This leads to foam generation by snap-off. At the tested fractional flows, no clear trend was observed between foam strength and fg. For a given permeability contrast, foam generation was observed at higher gas fractions than predicted by previous work (Rossen 1999). Significant fluctuations in pressure gradient accompanied the process of foam generation, indicating a degree of intermittency in the generation rate—probably reflecting cycles of foam generation, dryout, imbibition, and then generation. The intermittency of foam generation was found to increase with decreasing injection velocities and increasing fractional flow. Within the range of conditions tested, the onset of foam generation (identified by the rise in ▿P and Sg) occurs after roughly the same amount of surfactant injection, independent of fractional flow or injection rate.


SPE Journal ◽  
2017 ◽  
Vol 22 (05) ◽  
pp. 1326-1337 ◽  
Author(s):  
P. Ø. Andersen ◽  
S.. Evje ◽  
A.. Hiorth

Summary Imbibition experiments with porous disk can be used to derive accurate capillary pressure curves for porous media. An experimental setup is considered in which brine spontaneously imbibes cocurrently through a water-wet porous disk and into a mixed-wet core. Oil is produced from the core's top surface, which is exposed to oil. The capillary pressure is reduced in steps to determine points on the capillary pressure curve. A mathematical model is presented to interpret and design such experiments. The model was used to history match experimental data from Ahsan et al. (2012). An analytical model was then derived from a simplification of the general model, and validated by comparing the two by use of parameters from history matching. The main assumption of the analytical model is that the imbibition rate is sufficiently low, allowing fluids to redistribute inside the core, leading to a negligible capillary pressure gradient. This results in an exponential imbibition time profile with a time scale τ. Exponential matching has been applied earlier in the literature, but, for the first time, we derive this expression theoretically and provide an explicit formulation for the time scale. The numerical simulations show that, at low saturations, there can be a significant flow resistance in the core. A capillary-pressure gradient then forms, and the analytical solution overestimates the rate of recovery. At higher saturations, the fluids are more mobile, and imbibition rate is restricted by the disk. Under such conditions, the exponential solution is a good approximation. The demonstrated ability to predict the time scale in the late stage of the experiment is of significant benefit, because this part of the test is also the most time-consuming and most important to estimate. A method is presented to derive capillary pressure data point by point from measured imbibition data. It provides reliable data between the equilibrium points, and demonstrates consistent variations in flow resistance during the imbibition tests. Gravity had minor influence on the considered experimental data, but generally implies that equilibrium points have higher capillary pressure than the phase pressure difference defined by the boundary conditions.


Georesursy ◽  
2021 ◽  
Vol 23 (4) ◽  
pp. 44-50
Author(s):  
Mikhail Zaitsev ◽  
Nikolai Mikhailov ◽  
Ekaterina Tumanova

Filtration of oil in low-permeable reservoirs is considered. The experimental data of dependence of filtration velocity on pressure gradient are analysed. It is shown that the filtration law in low-permeability reservoirs differs from the linear Darcy’s law and from the non-linear law with an initial pressure gradient. The power law of filtration in low-permeability reservoirs is experimentally substantiated. Models of nonlinear filtration influence on flow rate are proposed. The analysis of influence of nonlinear filtration parameters on flow rate in technogenically modified near-wellbore zone is carried out.


SPE Journal ◽  
2013 ◽  
Vol 19 (01) ◽  
pp. 88-100 ◽  
Author(s):  
Y.. Zhou ◽  
J.O.. O. Helland ◽  
D.G.. G. Hatzignatiou

Summary We simulate transient behavior of viscous- and capillary-dominated water invasion at mixed-wet conditions directly in scanning-electron-microscope (SEM) images of Bentheim sandstone by treating the pore spaces as cross sections of straight tubes. Initial conditions are established by drainage and wettability alteration. Constant rate or differential pressure is imposed along the tube bundle. The phase pressures vary with positions along the tube length but remain unique in each cross section, consistent with 1D core-scale models. This leads to a nonlinear system of equations that are solved for the interface positions as a function of time. The cross-sectional fluid configurations are computed accurately at any capillary pressure and wetting condition by a semianalytical model that is based on free-energy minimization. The fluid conductances are estimated by newly derived explicit expressions that are shown to be in agreement with numerical computations performed directly on the cross-sectional fluid configurations. An SEM image of Bentheim sandstone is taken as input to the developed model for simulating the evolution of saturation profiles during waterfloods for different flow rates and several mixed-wet conditions, which are established with various initial water saturations and contact angles. It is demonstrated that the simulated saturation profiles depend strongly on initial water saturation at mixed-wet conditions. The saturation profiles exhibit increasingly gradual behavior in time as the contact angle, defined on the oil-wet solid surfaces, increases or the initial water saturation decreases. Front menisci associated with positive capillary pressures promote oil displacement by water, whereas for large and negative capillary pressures at small flow rates, oil displaces water because the associated front menisci retract. This results in the development of pronounced gradual saturation fronts at mixed-wet conditions. The waterfloods simulated at conditions established with a large initial water saturation and small contact angle on the oil-wet solid surfaces exhibit sharp Buckley-Leverett saturation profiles for high flow rates because the capillary pressure is small and less important. The shape of the saturation profiles is interpreted on the basis of the simulated capillary pressure curves and the corresponding fluid configurations occurring in the rock image.


1984 ◽  
Vol 49 (2) ◽  
pp. 490-505
Author(s):  
Vladimír Kudrna ◽  
Pavel Hasal ◽  
Jiří Vlček

The earlier proposed general approach for description of the non-ideal mixer is coupled with corresponding boundary conditions for the closed system. Some simplifications in this procedure result in relations which are in agreement with experimental data.


2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Shazia Perveen ◽  
Raziya Nadeem ◽  
Shaukat Ali ◽  
Yasir Jamil

Abstract Biochar caged zirconium ferrite (BC-ZrFe2O5) nanocomposites were fabricated and their adsorption capacity for Reactive Blue 19 (RB19) dye was evaluated in a fixed-bed column and batch sorption mode. The adsorption of dye onto BC-ZrFe2O5 NCs followed pseudo-second-order kinetics (R 2 = 0.998) and among isotherms, the experimental data was best fitted to Sips model as compared to Freundlich and Langmuir isotherms models. The influence of flow-rate (3–5 mL min−1), inlet RB19 dye concentration (20–100 mg L−1) and quantity of BC-ZrFe2O5 NCs (0.5–1.5 g) on fixed-bed sorption was elucidated by Box-Behnken experimental design. The saturation times (C t /C o  = 0.95) and breakthrough (C t /C o  = 0.05) were higher at lower flow-rates and higher dose of BC-ZrFe2O5 NCs. The saturation times decreased, but breakthrough was increased with the initial RB19 dye concentration. The treated volume was higher at low sorbent dose and influent concentration. Fractional bed utilization (FBU) increased with RB19 dye concentration and flow rates at low dose of BC-ZrFe2O5 NCs. Yan model was fitted best to breakthrough curves data as compared to Bohart-Adams and Thomas models. Results revealed that BC-ZrFe2O5 nanocomposite has promising adsorption efficiency and could be used for the adsorption of dyes from textile effluents.


Author(s):  
Stefan Schmid ◽  
Rudi Kulenovic ◽  
Eckart Laurien

For the validation of empirical models to calculate leakage flow rates in through-wall cracks of piping, reliable experimental data are essential. In this context, the Leakage Flow (LF) test rig was built up at the IKE for measurements of leakage flow rates with reduced pressure (maximum 1 MPA) and temperature (maximum 170 °C) compared to real plant conditions. The design of the test rig enables experimental investigations of through-wall cracks with different geometries and orientations by means of circular blank sheets with integrated cracks which are installed in the tubular test section of the test rig. In the paper, the experimental LF set-up and used measurement techniques are explained in detail. Furthermore, first leakage flow measurement results for one through-wall crack geometry and different imposed fluid pressures at ambient temperature conditions are presented and discussed. As an additional aspect the experimental data are used for the determination of the flow resistance of the investigated leak channel. Finally, the experimental results are compared with numerical results of WinLeck calculations to prove specifically in WinLeck implemented numerical models.


2021 ◽  
Author(s):  
Carlos Esteban Alfonso ◽  
Frédérique Fournier ◽  
Victor Alcobia

Abstract The determination of the petrophysical rock-types often lacks the inclusion of measured multiphase flow properties as the relative permeability curves. This is either the consequence of a limited number of SCAL relative permeability experiments, or due to the difficulty of linking the relative permeability characteristics to standard rock-types stemming from porosity, permeability and capillary pressure. However, as soon as the number of relative permeability curves is significant, they can be processed under the machine learning methodology stated by this paper. The process leads to an automatic definition of relative permeability based rock-types, from a precise and objective characterization of the curve shapes, which would not be achieved with a manual process. It improves the characterization of petrophysical rock-types, prior to their use in static and dynamic modeling. The machine learning approach analyzes the shapes of curves for their automatic classification. It develops a pattern recognition process combining the use of principal component analysis with a non-supervised clustering scheme. Before this, the set of relative permeability curves are pre-processed (normalization with the integration of irreducible water and residual oil saturations for the SCAL relative permeability samples from an imbibition experiment) and integrated under fractional flow curves. Fractional flow curves proved to be an effective way to unify the relative permeability of the two fluid phases, in a unique curve that characterizes the specific poral efficiency displacement of this rock sample. The methodology has been tested in a real data set from a carbonate reservoir having a significant number of relative permeability curves available for the study, in addition to capillary pressure, porosity and permeability data. The results evidenced the successful grouping of the relative permeability samples, according to their fractional flow curves, which allowed the classification of the rocks from poor to best displacement efficiency. This demonstrates the feasibility of the machine learning process for defining automatically rock-types from relative permeability data. The fractional flow rock-types were compared to rock-types obtained from capillary pressure analysis. The results indicated a lack of correspondence between the two series of rock-types, which testifies the additional information brought by the relative permeability data in a rock-typing study. Our results also expose the importance of having good quality SCAL experiments, with an accurate characterization of the saturation end-points, which are used for the normalization of the curves, and a consistent sampling for both capillary pressure and relative permeability measurements.


1968 ◽  
Vol 90 (2) ◽  
pp. 395-404 ◽  
Author(s):  
H. N. Ketola ◽  
J. M. McGrew

A theory of the partially wetted rotating disk is described and experimental data presented which verify the application of this theory in practical applications. Four different flow regimes may be identified according to the value of the disk Reynolds number and the spacing ratio between the disk and stationary wall. The analytical expressions for prediction of the pressure gradient developed and the frictional resistance are uniquely determined by the disk Reynolds number, spacing ratio, and the degree of wetting of the disk.


Sign in / Sign up

Export Citation Format

Share Document