Finite Element Analysis of Induced Stresses on Injection Wells using Plane Stress and Strain Elements

2015 ◽  
Author(s):  
U. B Ikponmwosa ◽  
E Nwankwo ◽  
K. O Bello ◽  
A. O Olafuyi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Plane Stress ◽  
Stress And Strain ◽  
Injection Wells ◽  
Element Analysis ◽  
Induced Stresses

Finite Element Analysis of Motor Box for EBZ160 Horizontal Roadheader

2015 ◽  
Vol 1090 ◽  
pp. 233-237
Author(s):  
Ji Jun Miao ◽  
Ri Sheng Long
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Optimal Design ◽  
Safety Factor ◽  
Stress And Strain ◽  
Element Analysis

In order to solve the cracking and poor reliability problems of motor box of Horizontal Roadheader, the static structural FEA (Finite Element Analysis) of cutting arm & motor box of the EBH160 Horizontal Roadheader was conducted, and the stress and strain contours of FEA were obtained. By comparing the calculated results, the safety factor of cutting arm & motor box was 1.36, which provides a reference for the optimal design of cutting arm & motor box.

Finite Element Analysis of Drilling Frame on Down-the-Hole Drill Based on Mechanical Mechanics and Mechanical Properties

2014 ◽  
Vol 908 ◽  
pp. 282-286
Author(s):  
Wan Rong Wu ◽  
Lin Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Working Condition ◽  
Slenderness Ratio ◽  
Stress And Strain ◽  
Limit States ◽  
Element Analysis ◽  
Practical Engineering ◽  
Structure Strength ◽  
Strength And Stiffness

Drilling frame on TD165CH Down-The-Hole Drill that has large slenderness ratio and be longer than 10m is one component of Down-The-Hole drill which is mainly subjected to load.In the process of drilling, drilling frame is not only subjected to loads which are like tensile, compression and torsion and so on, and be under the influence of impacting and vibration of impactor,the situation of force is complicated.By analysing of working condition of Down-The-Hole drill,there get all kinds of limit states of typical working conditions, and then using Ansys doing finite element analysis, there get distribution of the stress and strain of drilling frame and the result of modal analysis to check whether drilling frame meets the requirements of strength and stiffness or not,and whether it is possible to resonate with the impactor or not.By analysis,Structure strength and stiffness of drilling Frame on TD165CH Down-The-Hole drill meet the requirements of practical engineering, and drilling Frame does not resonate with the impactor.

Finite Element Analysis on Rack and Pinion of Roadheader

2013 ◽  
Vol 791-793 ◽  
pp. 718-721
Author(s):  
Man Man Xu ◽  
Yu Li ◽  
Sai Nan Xie ◽  
Qing Hua Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Spur Gear ◽  
Stress And Strain ◽  
Analysis Method ◽  
Element Analysis ◽  
The Road ◽  
The Finite Element Analysis ◽  
Gear Rack ◽  
Stress And Strain Distribution

To analyse the road-header rack and pinion by using the finite element analysis software COSMOS/WORKS. Compared to the traditional analytic calculation and numerical analysis method, it is more intuitively get 28 ° pressure angle spur gear rack meshing stress and strain distribution, which can rack and pinion improvements designed to provide scientific reference.

scholarly journals Finite Element Analysis of Needle Insertion Angle in Insulin Therapy

2019 ◽  
Vol 16 (4) ◽  
pp. 7512-7523
Author(s):  
Syakirah Mohamed Amin ◽  
Muhammad Hanif Ramlee ◽  
Hadafi Fitri Mohd Latip ◽  
Gan Hong Seng ◽  
Mohammed Rafiq Abdul Kadir
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Insulin Therapy ◽  
Maximum Stress ◽  
Three Dimensional ◽  
Needle Insertion ◽  
Stress And Strain ◽  
Medical Doctors ◽  
Element Analysis ◽  
Biomechanical Evaluation

Millions in the world suffering diabetes mellitus depends on insulin therapy to control their blood glucose level daily. However, the painful daily injections they need to take could lead to other complications if it is not done correctly. To date, it is suggested by many researchers and medical doctors that the needles should be inserted at any angles of 90º or 45º. Nevertheless, this recommendation has not been supported by clinical or biomechanical evaluation. Hence, this study evaluates the needle insertion for insulin therapy to find the favourable angles in order to reduce injury and pain onto the skin. Finite element analysis was done by  simulating the injection of three-dimensional (3D) needle model into a 3D skin model. The insertions were simulated at two different angles, which are 45ºand 90º with two different lengths of needles; 4 mm and 6 mm. This study concluded the favourable angle for 4 mm needle to be 90º while 6 mm needle was best to be inserted at 45º as these angles exerted the least maximum stress and strain onto the skin.

CAD/CAE on the Mould Plates of Vertical Type High-Pressure Grouting Machine

2012 ◽  
Vol 538-541 ◽  
pp. 2681-2684
Author(s):  
Zhi Cheng Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
3D Model ◽  
Stress And Strain ◽  
Analysis Software ◽  
Element Analysis ◽  
Pressure Grouting ◽  
Object Of Study

Took a type of ceramics for daily use vertical type high pressure grouting machine as the object of study, study the stress and strain of its upper and lower mould plates. Established their 3D model by CAD software Pro-E, and then import them into finite element analysis software to analysis the value and distribution of the stress and strain. The analysis results can provide some reference for design, and have some engineering and practical value.

scholarly journals Slatted Floors and Solid Floors: Stress and Strain on the Bovine Hoof Capsule Analyzed in Finite Element Analysis

2006 ◽  
Vol 89 (1) ◽  
pp. 155-162 ◽  
Author(s):  
C. Hinterhofer ◽  
J.C. Ferguson ◽  
V. Apprich ◽  
H. Haider ◽  
C. Stanek
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress And Strain ◽  
Element Analysis ◽  
Bovine Hoof
Sign in / Sign up

Export Citation Format

Share Document