Mobilization of Immobile Water: Connate-Water Mobility During Waterfloods In Heterogeneous Reservoirs

SPE Journal ◽  
2014 ◽  
Vol 20 (01) ◽  
pp. 88-98 ◽  
Author(s):  
Arne Graue ◽  
Johannes Ramsdal ◽  
Martin A. Fernø

Summary In a series of laboratory waterfloods, we investigate the extent of mixing of injection water and connate water, connate-water mobility, and connate-water banking during water injection for enhanced oil recovery (EOR). Local dynamic water saturations of connate water and injected water were imaged individually by use of a nuclear-tracer technique. The connate water was displaced from the pore space by the injected water and accumulated downstream in a connate-water bank that advanced toward the production end. The connate-water bank significantly reduced the contact between the injected water and mobile oil. During capillary displacement—i.e., during spontaneous imbibition without a viscous pressure drop—the connate water was also mobilized and accumulated downstream in the core. During viscous displacement—i.e. with a pressure gradient as small as 0.3 mbar/cm—the accumulated connate water was mobilized in a miscible displacement and produced from the core. Only a small mixing zone was observed between the injected and connate waters, even with fully miscible conditions by use of identical brine compositions. The results of the displacement mechanisms experimentally visualized in this work are important for water-based EOR techniques, including low-salinity-water and polymer injections, as well as any tertiary oil-recovery method based on chemical injection.

2021 ◽  
Author(s):  
Tanya Ann Mathews ◽  
Alex J.Cortes ◽  
Richard Bryant ◽  
Berna Hascakir

Abstract Steam injection is an effective heavy oil recovery method, however, poses several environmental concerns. Solvent injection methods are introduced in an attempt to combat these environmental concerns. This paper evaluates the effectiveness of a new solvent (VisRed) in the recovery of a Canadian bitumen and compares its results with toluene. While VisRed is selected due to its high effectiveness as a viscosity reducer even at very low concentrations, toluene is selected due to its high solvent power. Five core flooding experiments were conducted; E1 (Steam flooding), E2 (VisRed flooding), E3 (Toluene flooding), E4 (Steam + Toluene flooding), and E5 (Steam + VisRed flooding). Core samples were prepared by saturating 60% of the pore space with oil samples and 40% with deionized water. The solvents were injected at a 2 ml/min rate, while steam was injected at a 18 ml/min cold water equivalent rate. Produced oil and water samples were collected every 20 min during every experiment. The oil recovery efficiencies of the core flood experiments were analyzed by the emulsion characterization in the produced fluids and the residual oil analysis on the spent rock samples. The best oil recovery of ~30 vol % was obtained for E2 (VisRed) in which VisRed was injected alone. Although similar cumulative recoveries were obtained both for E2 (VisRed) and E3 (Toluene), the amount of VisRed injected [~1 pore volumes (PV)] was half the volume required by toluene (~2 PV). The produced oil quality variations are mainly due to the formation of the water-in-oil emulsions during mainly steam processes (E1, E4, and E5). The increased amount of the polar fractions in the produced oil enhances the formation of the emulsions. These polar fractions are namely asphaltenes and resins. As the amount of the polar fractions in the produce oil increases, more water-in-oil emulsion formation is observed due to the polar-polar interaction between crude oil fractions and water. Consequently, E1 and E5 resulted in more water in oil emulsions. The cost analysis also shows the effectiveness of solvent recovery over steam-solvent recovery processes.


2016 ◽  
Vol 6 (1) ◽  
pp. 14
Author(s):  
H. Karimaie ◽  
O. Torsæter

The purpose of the three experiments described in this paper is to investigate the efficiency of secondary andtertiary gas injection in fractured carbonate reservoirs, focusing on the effect of equilibrium gas,re-pressurization and non-equilibrium gas. A weakly water-wet sample from Asmari limestone which is the mainoil producing formation in Iran, was placed vertically in a specially designed core holder surrounded withfracture. The unique feature of the apparatus used in the experiment, is the capability of initializing the samplewith live oil to obtain a homogeneous saturation and create the fracture around it by using a special alloy whichis easily meltable. After initializing the sample, the alloy can be drained from the bottom of the modified coreholder and create the fracture which is filled with live oil and surrounded the sample. Pressure and temperaturewere selected in the experiments to give proper interfacial tensions which have been measured experimentally.Series of secondary and tertiary gas injection were carried out using equilibrium and non-equilibrium gas.Experiments have been performed at different pressures and effect of reduction of interfacial tension werechecked by re-pressurization process. The experiments showed little oil recovery due to water injection whilesignificant amount of oil has been produced due to equilibrium gas injection and re-pressurization. Results alsoreveal that CO2 injection is a very efficient recovery method while injection of C1 can also improve the oilrecovery.


2020 ◽  
Vol 21 (2) ◽  
pp. 339
Author(s):  
I. Carneiro ◽  
M. Borges ◽  
S. Malta

In this work,we present three-dimensional numerical simulations of water-oil flow in porous media in order to analyze the influence of the heterogeneities in the porosity and permeability fields and, mainly, their relationships upon the phenomenon known in the literature as viscous fingering. For this, typical scenarios of heterogeneous reservoirs submitted to water injection (secondary recovery method) are considered. The results show that the porosity heterogeneities have a markable influence in the flow behavior when the permeability is closely related with porosity, for example, by the Kozeny-Carman (KC) relation.This kind of positive relation leads to a larger oil recovery, as the areas of high permeability(higher flow velocities) are associated with areas of high porosity (higher volume of pores), causing a delay in the breakthrough time. On the other hand, when both fields (porosity and permeability) are heterogeneous but independent of each other the influence of the porosity heterogeneities is smaller and may be negligible.


2019 ◽  
Vol 89 ◽  
pp. 02006
Author(s):  
F. Feldmann ◽  
A. M. AlSumaiti ◽  
S. K. Masalmeh ◽  
W. S. AlAmeri ◽  
S. Oedai

Low salinity water flooding (LSF) is a relatively simple and cheap EOR technique in which the salinit y of the injected water is optimized (by desalination and/or modification) to improve oil recovery over conventional waterflooding. Extensive laboratory experiments investigating the effect of LSF are available in the literature. Sulfate-rich as well as diluted brines have shown promising potential to increase oil production in limestone core samples. To quantify the low salinity effect, spontaneous imbibition and/or tertiary waterflooding experiments have been reported. For the first time in literature, this paper presents a comprehensive study of the centrifuge technique to investigate low salinity effect in carbonate samples. The study is divided into three parts. At first, a comprehensive screening was performed on the impact of different connate water and imbibition brine compositions/combinations on the spontaneous imbibition behavior. Second, the subsequent forced imbibition of the samples using the centrifuge method to investigate the impact of brine compositions on residual saturations and capillary pressure. Finally, three unsteady-state (USS) core floodings were conducted in order to examine the potential of the different brines to increase oil recovery in secondary mode (brine injection at connate water saturation) and tertiary mode (exchange of injection brine at mature recovery stage). The experiments were performed using Indiana limestone outcrops. The main conclusions of the study are spontaneous imbibition experiments only showed oil recovery in case the salinity of the imbibing water (IW) is lower than the salinity of the connate water (CW). No oil production was observed when the imbibing water had a higher salinity than the connate water or the salinity of the connate water and imbibing brine were identical. Moreover, the spontaneous imbibition experiments indicated that diluting the salinity of the imbibing water has a larger potential to spontaneously recover oil than the introduction of sulfate-rich sea water. The centrifuge experiments confirmed a connection between the overall salinity and oil recovery. As the salinity of the imbibing brines decreases, the capillary imbibition pressure curves showed an increasing water-wetting tendency and simultaneous reduction of the remaining oil saturation. The lowest remaining oil saturation was obtained for diluted sea water as CW and IW. The core flooding experiments reflected the results of the spontaneous imbibition and centrifuge experiments. Injecting brine at a rate of 0.05 cc/min, sea water and especially diluted sea water resulted in a significant higher oil recovery compared to formation brine. Moreover, when comparing secondary mode experiments, the remaining oil saturation after flooding by diluted sea water, sea water and formation water was 30.6 %, 35.5 % and 37.4 %, respectively. In tertiary injection mode, sea water did not lead to extra oil recovery while diluted sea water led to an additional oil recovery of 5.6 % in one out of two tertiary injection applications.


SPE Journal ◽  
2020 ◽  
pp. 1-9
Author(s):  
Emmanuel Ajoma ◽  
Thanarat Sungkachart ◽  
Saria ◽  
Hang Yin ◽  
Furqan Le-Hussain

Summary To determine the effect on oil recovery and carbon dioxide (CO2) storage, laboratory experiments are run with various fractions of CO2 injected (FCI): pure CO2 injection (FCI = 1), water-saturated CO2 (wsCO2) injection (FCI = 0.993), simultaneous water and gas (SWAG) (CO2) injection (FCI = 0.75), carbonated water injection (CWI) (FCI = 0.007), and water injection (FCI = 0). All experiments are performed on Bentheimer sandstone cores at 70°C and 11.7 MPa (1,700 psia). The oil phase is composed of 65% hexane and 35% decane by molar fraction. Before any fluid is injected, the core is filled with oil and irreducible water. Pressure difference across the core and production rate of gas are measured during the experiment. The collected produced fluids are analyzed in a gas chromatograph to determine their composition. Cumulative oil recovery after injection is found to be 78 to 83% for wsCO2, 78% for SWAG, 74% for pure CO2, 53% for CWI, and 35% for water. Net CO2 stored is also found to be the highest for wsCO2 (59 to 65% of the pore volume), followed by that for CO2 injection (56%) and that for SWAG (42%). These results suggest that wsCO2 injection might outperform pure CO2 injection at both oil recovery and net CO2stored.


2006 ◽  
Vol 9 (04) ◽  
pp. 295-301 ◽  
Author(s):  
Kewen Li ◽  
Kevin Chow ◽  
Roland N. Horne

Summary It has been a challenge to understand why recovery by spontaneous imbibition could both increase and decrease with initial water saturation. To this end, mathematical models were developed with porosity, permeability, viscosity, relative permeability, capillary pressure, and initial water saturation included. These equations foresee that recovery and imbibition rate can increase, remain unchanged, or decrease with an increase in initial water saturation, depending on rock properties, the quantity of residual gas saturation, the range of initial water saturation, and the units used in the definitions of gas recovery and imbibition rate. The theoretical predictions were verified experimentally by conducting spontaneous water imbibition at five different initial water saturations, ranging from 0 to approximately 50%. The effects of initial water saturation on residual saturation, relative permeability, capillary pressure, imbibition rate, and recovery in gas/water/rock systems by cocurrent spontaneous imbibition were investigated both theoretically and experimentally. Water-phase relative permeabilities and capillary pressures were calculated with the experimental data of spontaneous imbibition. Experimental results in different rocks were compared. Introduction Spontaneous water imbibition is an important mechanism during water injection. Prediction of recovery and imbibition rate by spontaneous water imbibition is essential to evaluate the feasibility and the performance of water injection. For example, is water injection effective in the case of high initial water saturation in reservoirs? Answers to such a question may be found by investigating the effect of initial water saturation on spontaneous water imbibition. It has been observed experimentally that initial water saturation affects recovery and production rate significantly (Blair 1964; Zhou et al. 2000; Viksund et al. 1998; Cil et al. 1998; Tong et al. 2001; Li and Firoozabadi 2000; Akin et al. 2000). However, the experimental observations from different authors (Zhou et al. 2000; Cil et al. 1998; Li and Firoozabadi 2000; Akin et al. 2000) are not consistent. On the other hand, few studies have investigated the effect of initial water saturation on recovery and imbibition rate theoretically, especially in gas reservoirs. Using numerical-simulation techniques, Blair (1964) found that the quantity and the rate of oil produced after a given period of imbibition increased with a decrease in initial water saturation for countercurrent spontaneous imbibition. Zhou et al. (2000) found that both imbibition rate and final oil recovery in terms of oil originally in place (OOIP) increased with an increase in initial water saturation, whereas oil recovery by waterflooding decreased. Viksund et al. (1998) found that the final oil recovery (OOIP) by spontaneous water imbibition in Berea sandstone showed little variation with a change in initial water saturation from 0 to approximately 30%. For the chalk samples tested by Viksund et al. (1998), the imbibition rate first increased with an increase in initial water saturation and then decreased slightly as initial water saturation increased above 34%.Cil et al. (1998) reported that the oil recovery (in terms of recoverable oil reserves) for zero and 20% initial water saturation showed insignificant differences in behavior. However, the oil recovery for initial water saturation above 20% increased with an increase in initial water saturation. Li and Firoozabadi (2000) found that the final gas recovery in the units of gas originally in place (GOIP) by spontaneous imbibition decreased with an increase in initial water saturation in both gas/oil/rock and gas/water/rock systems. The imbibition rate (GOIP/min) increased with an increase in initial water saturation at early time but decreased at later time. Akin et al. (2000) found that the residual oil saturation was unaffected significantly by initial water saturation. In this study, equations, derived theoretically, were used to study the effect of initial water saturation on gas recovery and imbibition rate. The equations correlate recovery, imbibition rate, initial water saturation, rock/fluid properties, and other parameters. Experiments of spontaneous water imbibition in gas-saturated rocks were conducted to confirm the theoretical predictions. The effect of rock properties on gas recovery and imbibition rate was also studied. An X-ray CT scanner was used to monitor the distribution of the initial water saturation to confirm that the initial distribution of the water saturation was uniform. In this study, we only focused on cocurrent spontaneous imbibition. It was assumed that there were no chemical reactions or mass transfer between gas and liquid.


2020 ◽  
Vol 10 (2) ◽  
pp. 17-26
Author(s):  
Gustavo Maya Toro ◽  
Luisana Cardona Rojas ◽  
Mayra Fernanda Rueda Pelayo ◽  
Farid B. Cortes Correa

Low salinity water injection has been frequently studied as an enhanced oil recovery process (EOR), mainly due to promising experimental results and because operational needs are not very different from those of the conventional water injection. However, there is no agreement on the mechanisms involved in increasing the displacement of crude oil, except for the effects of wettability changes. Water injection is the oil recovery method mostly used, and considering the characteristics of Colombian oil fields, this study analyses the effect of modifying the ionic composition of the waters involved in the process, starting from the concept of ionic strength (IS) in sandstone type rocks. The experimental plan for this research includes the evaluation of spontaneous imbibition (SI), contact angles, and displacement efficiencies in Berea core plugs. Interfacial tension and pH measurements were also carried out. The initial scenario consists in formation water (FW), with a total concentration of 9,800 ppm (TDS) (IS ~ 0.17) and a 27 °API crude oil. Magnesium and Calcium brine were also used in a first approach to assess the effect of the divalent ions. Displacement efficiency tests are performed using IS of 0.17, 0.08, and 0.05, as secondary and tertiary oil recovery and the recovery of oil increases in both scenarios. Spontaneous imbibition curves and contact angle measurements show variations as a function of the ionic strength, validating the displacement efficiencies. Interfacial tension and pH collected data evidence that fluid/fluid interactions occur due to ionic strength modifications. However, as per the conditions of this research, fluid/fluid mechanisms are not as determining as fluid/rock.


Author(s):  
Leonardo Fonseca Reginato ◽  
Lucas Gomes Pedroni ◽  
André Luiz Martins Compan ◽  
Rodrigo Skinner ◽  
Marcio Augusto Sampaio

Engineered Water Injection (EWI) has been increasingly tested and applied to enhance fluid displacement in reservoirs. The modification of ionic concentration provides interactions with the pore wall, which facilitates the oil mobility. This mechanism in carbonates alters the natural rock wettability being quite an attractive recovery method. Currently, numerical simulation with this injection method remains limited to simplified models based on experimental data. Therefore, this study uses Artificial Neural Networks (ANN) learnability to incorporate the analytical correlation between the ionic combination and the relative permeability (Kr), which depicts the wettability alteration. The ionic composition in the injection system of a Brazilian Pre-Salt benchmark is optimized to maximize the Net Present Value (NPV) of the field. The optimization results indicate the EWI to be the most profitable method for the cases tested. EWI also increased oil recovery by about 8.7% with the same injected amount and reduced the accumulated water production around 52%, compared to the common water injection.


Sign in / Sign up

Export Citation Format

Share Document