A New Approach To Estimate Invasion Radius of Water-Based-Drilling-Fluid Filtrate To Evaluate Formation Damage Caused by Overbalanced Drilling

2015 ◽  
Vol 30 (01) ◽  
pp. 27-37 ◽  
Author(s):  
Kegang Ling ◽  
He Zhang ◽  
Zheng Shen ◽  
Ali Ghalambor ◽  
Guoqing Han ◽  
...  
Keyword(s):  
Drilling Fluid ◽  
Formation Damage ◽  
New Approach ◽  
Water Based

scholarly journals Experimental study on thermal, rheological and filtration control characteristics of drilling fluids: effect of nanoadditives

2020 ◽  
Vol 75 ◽  
pp. 36
Author(s):  
Erfan Veisi ◽  
Mastaneh Hajipour ◽  
Ebrahim Biniaz Delijani
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Drilling Fluid ◽  
Formation Damage ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Drill Bit ◽  
Rheological Characteristics ◽  
Cu Nanoparticles ◽  
Water Based

Cooling the drill bit is one of the major functions of drilling fluids, especially in high temperature deep drilling operations. Designing stable drilling fluids with proper thermal properties is a great challenge. Identifying appropriate additives for the drilling fluid can mitigate drill-bit erosion or deformation caused by induced thermal stress. The unique advantages of nanoparticles may enhance thermal characteristics of drilling fluids. The impacts of nanoparticles on the specific heat capacity, thermal conductivity, rheological, and filtration control characteristics of water‐based drilling fluids were experimentally investigated and compared in this study. Al2O3, CuO, and Cu nanoparticles were used to prepare the water-based drilling nanofluid samples with various concentrations, using the two-step method. Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD) were utilized to study the nanoparticle samples. The nanofluids stability and particle size distribution were, furthermore, examined using Dynamic Light Scattering (DLS). The experimental results indicated that thermal and rheological characteristics are enhanced in the presence of nanoparticles. The best enhancement in drilling fluid heat capacity and thermal conductivity was obtained as 15.6% and 12%, respectively by adding 0.9 wt% Cu nanoparticles. Furthermore, significant improvement was observed in the rheological characteristics such as the apparent and plastic viscosities, yield point, and gel strength of the drilling nanofluids compared to the base drilling fluid. Addition of nanoparticles resulted in reduced fluid loss and formation damage. The permeability of filter cakes decreased with increasing the nanoparticles concentration, but no significant effect in filter cake thickness was observed. The results reveal that the application of nanoparticles may reduce drill-bit replacement costs by improving the thermal and drilling fluid rheological characteristics and decrease the formation damage due to mud filtrate invasion.

Insights into the Application of Surfactants and Nanomaterials as Shale Inhibitors for Water-based Drilling Fluid: A Review

2021 ◽  
pp. 103987
Author(s):  
Nasiru Salahu Muhammed ◽  
Teslim Olayiwola ◽  
Salaheldin Elkatatny ◽  
Bashirul Haq ◽  
Shirish Patil
Keyword(s):  
Drilling Fluid ◽  
Application Of Surfactants ◽  
Water Based

Investigation on Methane Hydrate Formation in Water-based Drilling Fluid

2021 ◽  
Vol 35 (6) ◽  
pp. 5264-5270
Author(s):  
Yong He ◽  
Zhen Long ◽  
Jingsheng Lu ◽  
Lingli Shi ◽  
Wen Yan ◽  
...  
Keyword(s):  
Methane Hydrate ◽  
Drilling Fluid ◽  
Hydrate Formation ◽  
Water Based

scholarly journals Wet Drilled Cuttings Bed Rheology

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1644
Author(s):  
Camilo Pedrosa ◽  
Arild Saasen ◽  
Bjørnar Lund ◽  
Jan David Ytrehus
Keyword(s):  
Drilling Fluid ◽  
Drilling Fluids ◽  
Parallel Plates ◽  
Single Particles ◽  
Cuttings Transport ◽  
Transport Studies ◽  
Water Based ◽  
Fluid Properties ◽  
External Forces ◽  
Cuttings Bed

The cuttings transport efficiency of various drilling fluids has been studied in several approaches. This is an important aspect, since hole cleaning is often a bottleneck in well construction. The studies so far have targeted the drilling fluid cuttings’ transport capability through experiments, simulations or field data. Observed differences in the efficiency due to changes in the drilling fluid properties and compositions have been reported but not always fully understood. In this study, the cuttings bed, wetted with a single drilling fluid, was evaluated. The experiments were performed with parallel plates in an Anton Paar Physica 301 rheometer. The results showed systematic differences in the internal friction behaviors between tests of beds with oil-based and beds with water-based fluids. The observations indicated that cutting beds wetted with a polymeric water-based fluid released clusters of particles when external forces overcame the bonding forces and the beds started to break up. Similarly, it was observed that an oil-based fluid wetted bed allowed particles to break free as single particles. These findings may explain the observed differences in previous cutting transport studies.

Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Arild Saasen
Keyword(s):  
Rheological Properties ◽  
Pressure Loss ◽  
Drilling Fluid ◽  
Axial Flow ◽  
Drilling Fluids ◽  
Unstable Flow ◽  
Pressure Losses ◽  
Shear Dependent Viscosity ◽  
Water Based ◽  
Dependent Viscosity

Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.

scholarly journals Minimizing the filtration loss of water-based drilling fluid with sustainable basil seed powder

Petroleum ◽  
2021 ◽  
Author(s):  
Hanyi Zhong ◽  
Xin Gao ◽  
Xianbin Zhang ◽  
Anliang Chen ◽  
Zhengsong Qiu ◽  
...  
Keyword(s):  
Drilling Fluid ◽  
Filtration Loss ◽  
Water Based
Sign in / Sign up

Export Citation Format

Share Document