The Impact of LoSal on Oil Recovery from a Selected Carbonate Reservoir in Abu Dhabi - An Experimental Approach

2013 ◽  
Author(s):  
H. H. Al-Attar ◽  
M. Y. Mahmoud ◽  
A. Y. Zekri ◽  
R. A. Almehaideb ◽  
M. T. Ghannam
Keyword(s):  
Oil Recovery ◽  
Experimental Approach ◽  
Carbonate Reservoir ◽  
Abu Dhabi ◽  
The Impact

scholarly journals MODEL-BASED OPTIMIZATION OF CYCLES OF CO2 WATER-ALTERNATING-GAS (CO2-WAG) INJECTION IN CARBONATE RESERVOIR

2022 ◽  
Vol 15 (4) ◽  
pp. 139-149
Author(s):  
F. G. A. Pereira ◽  
V. E. Botechia ◽  
D. J. Schiozer
Keyword(s):  
Oil Recovery ◽  
Carbonate Reservoir ◽  
Co2 Production ◽  
Co2 Injection ◽  
Optimal Size ◽  
Control Variables ◽  
Limit Values ◽  
Water Alternating Gas ◽  
Production Wells ◽  
The Impact

Pre-salt reservoirs are among the most important discoveries in recent decades due to the large quantities of oil in them. However, high levels of uncertainties related to its large gas/CO2 production prompt a more complex gas/CO2 management, including the use of alternating water and gas/CO2 injection (WAG) as a recovery mechanism to increase oil recovery from the field. The purpose of this work is to develop a methodology to manage cycle sizes of the WAG/CO2, and analyze the impact of other variables related to the management of producing wells during the process. The methodology was applied to a benchmark synthetic reservoir model with pre-salt characteristics. We used five approaches to evaluate the optimum cycle size under study, also assessing the impact of the management of producing wells: (A) without closing producers due to gas-oil ratio (GOR) limit; (B) GOR limit fixed at a fixed value (1600 m³/m³) for all wells; (C) GOR limit optimized per well; (D) joint optimization between GOR limit values of producers and WAG cycles; and (E) optimization of the cycle size per injector well with an optimized GOR limit. The results showed that the optimum cycle size depends on the management of the producers. Leaving all production wells open until the end of the field's life (without closing based on the GOR limit) or controlling the wells in a more restricted manner (with closing based on the GOR limit), led to significant variation of the results (optimal size of the WAG/CO2 cycles). Our study, therefore, demonstrates that the optimum cycle size depends on other control variables and can change significantly due to these variables. This work presents a study that aimed to manage the WAG-CO2 injection cycle size by optimizing the life cycle control variables to obtain better economic performance within the premises already established, such as the total reinjection of gas/CO2 produced, also analyzing the impact of other variables (management of producing wells) along with the WAG-CO2 cycles.

scholarly journals Oil recovery for fractured-vuggy carbonate reservoirs by cyclic water huff and puff: performance analysis and prediction

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Daigang Wang ◽  
Jingjing Sun
Keyword(s):  
Oil Recovery ◽  
History Matching ◽  
High Efficiency ◽  
Carbonate Reservoir ◽  
Carbonate Reservoirs ◽  
Production Performance ◽  
Quantitative Prediction ◽  
Attractive Alternative ◽  
Marquardt Algorithm ◽  
The Impact

Abstract Cyclic water huff and puff (CWHP) has proven to be an attractive alternative to improve oil production performance after depletion-drive recovery in fractured-vuggy carbonate reservoirs. However, due to the impact of strong heterogeneity, multiple types of fractured-vuggy medium, poor connectivity, complex flow behaviors and oil-water relationship, CWHP is merely suitable for specific types of natural fractured-vuggy medium, usually causing a great difference in actual oil-yielding effect. It remains a great challenge for accurate evaluation of CWHP adaptability and quantitative prediction of production performance in fractured-vuggy carbonate reservoir, which severely restricts the application of CWHP. For this study, we firstly enable the newly developed fuzzy grey relational analysis to quantify the adaptability of CWHP. With production history of several targeted producers, the accuracy of the proposed method is validated. Based on the traditional percolation theory and waterflood mechanisms in various types of fractured-vuggy medium, a quantitative prediction model for cyclic water cut fwp and increased recovery factor ΔR is presented. The CWHP production performance is discussed by using the Levenberg-Marquardt algorithm for history matching. With a better understanding of the fwp ~ ΔR curve characteristics in different types of fractured-vuggy medium, proper strategies or measures for potential-tapping remaining oil are provided. This methodology can also offer a good basis for engineers and geologists to develop other similar reservoirs with high efficiency.

Numerical Simulations of Surfactant Flooding in Carbonate Reservoirs: The Impact of Geological Heterogeneities Across Scales

2021 ◽  
Author(s):  
Jackson Pola ◽  
Sebastian Geiger ◽  
Eric Mackay ◽  
Christine Maier ◽  
Ali Al-Rudaini
Keyword(s):  
Oil Recovery ◽  
Carbonate Reservoir ◽  
Spontaneous Imbibition ◽  
Numerical Dispersion ◽  
Surfactant Flooding ◽  
Production Forecast ◽  
Geological Heterogeneity ◽  
Grid Coarsening ◽  
The Impact ◽  
The Way

Abstract We demonstrate how geological heterogeneity impacts the effectiveness of surfactant-based enhanced oil recovery (EOR) at larger (inter-well and sector) scales when upscaling small (core) scale heterogeneity and physicochemical processes. We used two experimental datasets of surfactant-based EOR where spontaneous imbibition and viscous displacement, respectively dominate recovery. We built 3D core-scale simulation models to match the data and parameterize surfactant models. The results were deployed in high-resolution models that preserve the complexity and heterogeneity of carbonate formations in the inter-well and sector scale. These larger-scale models were based on two outcrop analogues from France and Morroco, respectively, which capture the reservoir architectures inherent to the productive carbonate reservoir systems in the Middle East. We then assessed and quantified the error in production forecast that arises due to upscaling, upgridding, and simplification of geological heterogeneity. Simulation results showed a broad range of recovery predictions. The variability arises from the choice of surfactant model parameterization (i.e., spontaneous imbibition vs viscous displacement) and the way the heterogeneity in the inter-well and sector models was upscaled and simplified. We found that the parameterization of surfactant models has a significant impact on recovery predictions. Oil recovery at the larger scale was observed to be higher when using the parametrization derived from viscous displacement experiments compared to parameterization from spontaneous imbibition experiments. This observation clearly demonstrated how core-scale processes impact recovery predictions at the larger scales. Also, the variability in recovery prediction due to the choice of surfactant model was as large as the variability arising from upscaling and upgridding. Upscaled and upgridded models overestimated recovery because of the simplified geology. Grid coarsening exacerbated this effect because of the increased numerical dispersion. These results emphasize the need to use correctly configured surfactant models, appropriate grid resolution that minimizes numerical dispersion, and properly upscaled reservoir models to accurately forecast surfactant floods. Our findings present new insights into how the uncertainty in production forecasts during surfactant flooding depends on the way surfactant models are parameterized, how the reservoir geology is upscaled, and how numerical dispersion is impacted by grid coarsening.

scholarly journals The impact of permeability heterogeneity on water-alternating-gas displacement in highly stratified heterogeneous reservoirs

2021 ◽  
Author(s):  
Mohammad Yunus Khan ◽  
Ajay Mandal
Keyword(s):  
Oil Recovery ◽  
Field Application ◽  
Carbonate Reservoir ◽  
High Permeability ◽  
Oil Saturation ◽  
Heterogeneous Reservoirs ◽  
Heterogeneous Reservoir ◽  
Low Viscosity ◽  
Water Alternating Gas ◽  
The Impact

AbstractAvailability of gases at the field level makes attractive to water-alternating-gas (WAG) process for low viscosity and light oils carbonate reservoir. However, impact of reservoir heterogeneity on WAG performance is crucial before field application. In general, ramp carbonates have heterogeneity due to variation of permeability and porosity. However, WAG performance significantly affected by permeability variations. This article investigates merits and demerits of WAG displacement due to permeability heterogeneities such as permeability anisotropy, high permeability streaks (HKS), matrix permeability, dolomite and thin dense stylolite layers. High-resolution compositional simulations with tuned equation of state (EoS) were carried out using 2D and 3D sector models. The study focuses on WAG performance in terms of oil recovery, vertical sweep, solvent utilization, gas oil ratio (GOR), water cut (WCT), WAG response time, gravity override, hysteresis, un-contacted oil saturation and economics. The results of simulation show that the heterogeneous reservoir provides initially faster WAG response, lower expected ultimate recovery (EUR), faster gas breakthrough, higher GOR and WCT production compared to homogeneous reservoir. The gas gravity override at smaller wells spacing is less in homogeneous reservoir as compared to heterogeneous reservoir, but it is reverse in case of larger well spacing. In heterogeneous reservoir, the HKS shows significant gas override resulting in poor vertical sweep due to capillary holding, and the high permeability dolomite layer shows early water breakthrough. This reservoir has higher solvent utilization in initial stage, and then, it becomes nearly equal to homogeneous reservoir. Simulation in both reservoirs overestimates incremental recovery of 2–3% OOIP at one pore volume injection because of not involving un-contacted oil saturation as predicted in core flood. The findings of this study will help to understand WAG performance and design in highly heterogeneous reservoirs for field applications. Graphical abstract

Feasibility of Waterflooding for a Carbonate Oil Field Through Whole-Field Simulation Studies

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Wenting Yue ◽  
John Yilin Wang
Keyword(s):  
Oil Recovery ◽  
Injection Rate ◽  
Carbonate Reservoir ◽  
Oil Field ◽  
Improved Oil Recovery ◽  
Smackover Formation ◽  
Artificial Lift ◽  
Production History ◽  
Current Production ◽  
The Impact

The carbonate oil field studied is a currently producing field in U.S., which is named “PSU” field to remain anonymity. Discovered in 1994 with wells on natural flow or through artificial lift, this field had produced 17.8 × 106 bbl of oil to date. It was noticed that gas oil ratio had increased in certain parts and oil production declined with time. This study was undertaken to better understand and optimize management and operation of this field. In this brief, we first reviewed the geology, petrophysical properties, and field production history of PSU field. We then evaluated current production histories with decline curve analysis, developed a numerical reservoir model through matching production and pressure data, then carried out parametric studies to investigate the impact of injection rate, injection locations, and timing of injection, and finally developed optimized improved oil recovery (OIR) methods based on ultimate oil recovery and economics. This brief provides an addition to the list of carbonate fields available in the petroleum literature and also improved understandings of Smackover formation and similar analogous fields. By documenting key features of carbonated oil field performances, we help petroleum engineers, researchers, and students understand carbonate reservoir performances.

Challenges of Optimizing Oil Recovery of "Tight Carbonate" Reservoir, Onshore Abu Dhabi Oil Field, United Arab Emirates

2008 ◽  
Author(s):  
Mohamed Benlacheheb ◽  
Adib Edris ◽  
Omar Sultan Al Jeelani ◽  
Salman Hassan Al Marzouqi ◽  
Maryam Al Sheehi ◽  
...  
Keyword(s):  
United Arab Emirates ◽  
Oil Recovery ◽  
Carbonate Reservoir ◽  
Oil Field ◽  
Abu Dhabi ◽  
Tight Carbonate

Comparison of Oil Recovery and Carbonate Rock’s Properties Alterations by CO2 Miscible Flooding

2018 ◽  
Author(s):  
Jinju Han ◽  
Youngjin Seo ◽  
Juhyun Kim ◽  
Sunlee Han ◽  
Youngsoo Lee
Keyword(s):  
Pore Structure ◽  
Oil Recovery ◽  
Carbonate Rock ◽  
Flow Path ◽  
Carbonate Reservoir ◽  
Rock Properties ◽  
Co2 Flooding ◽  
Miscible Flooding ◽  
The Impact ◽  
Indiana Limestone

This present study indicates experimental investigation about the impact of CO2 flooding on oil recovery and rock’s properties alteration in carbonate reservoir under the miscible condition. In order to compare the effect to initial pore characteristic, two type of carbonate rock was used; an Edward white represents homogeneous mainly consisted micropore, whereas an Indiana limestone represented heterogeneous mainly consisted macropore in this study. Under the miscible condition (9.65 MPa and 40°C), five pore volume of CO2 were injected into oil-wet carbonate rock, which was fully saturated with oil and connate water. After CO2 flooding, several analyses for each sample conducted to investigate oil recovery and rock properties change in porosity, permeability, and pore structure by chemical and physical reaction between CO2, water, and carbonate mineral before and after CO2 flooding by using core analysis, MICP, SEM, ICP, and X-ray CT techniques. From the results of oil recovery, it was more effective and larger in Edward white than in Indiana limestone. Because homogeneous characteristic with a large ratio of low permeable micropore in Edward white contributed to occur long reaction time between oil and CO2 for enough miscibility as well as to displace stably oil by CO2. Conversely, heterogeneous pore structure mainly consisted of high permeable conduit (macropore) in Indiana limestone has brought ineffective and low oil production. From the analysis of rock’s properties alteration, we found that, for the homogeneous sample, dissolution dominantly changed pore structure and became better flow path by improving permeability and reducing tortuosity. While plugging by precipitation of mineral particles was not critically affected rock’ properties, despite the sample mainly consisted small pores. In the case of the heterogeneous sample, both dissolution and precipitation critically affected change of rock’s properties and pore structure. In particular, superior precipitation in complex pore network seriously damaged flow path and change of rock’s properties. The largest porosity change markedly appeared in inlet section because of exposing rock surface from fresh CO2 during a long time. In conclusion, it shows that CO2 miscible flooding in carbonate reservoirs significantly affected to alteration of rock’s properties such as porosity, permeability, tortuosity, and pore connectivity, in particular in heterogeneous system compared with in homogeneous system. These experimental results can be useful to characterize carbonate rock as well as to study rock properties alteration on CO2 EOR and CCS processes.

scholarly journals Experimental Studies of Immiscible High-Nitrogen Natural Gas WAG Injection Efficiency in Mixed-Wet Carbonate Reservoir

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2346
Author(s):  
Mirosław Wojnicki ◽  
Jan Lubaś ◽  
Marcin Warnecki ◽  
Jerzy Kuśnierczyk ◽  
Sławomir Szuflita
Keyword(s):  
Natural Gas ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Experimental Studies ◽  
Carbonate Reservoir ◽  
High Nitrogen ◽  
The Impact ◽  
Wag Injection

Crucial oil reservoirs are located in naturally fractured carbonate formations and are currently reaching a mature phase of production. Hence, a cost-effective enhanced oil recovery (EOR) method is needed to achieve a satisfactory recovery factor. The paper focuses on an experimental investigation of the efficiency of water alternating sour and high-nitrogen (~85% N2) natural gas injection (WAG) in mixed-wetted carbonates that are crucial reservoir rocks for Polish oil fields. The foam-assisted water alternating gas method (FAWAG) was also tested. Both were compared with continuous water injection (CWI) and continuous gas injection (CGI). A series of coreflooding experiments were conducted within reservoir conditions (T = 126 ℃, P = 270 bar) on composite cores, and each consisted of four reservoir dolomite core plugs and was saturated with the original reservoir fluids. In turn, some of the experiments were conducted on artificially fractured cores to evaluate the impact of fractures on recovery efficiency. The performance evaluation of the tested methods was carried out by comparing oil recoveries from non-fractured composite cores, as well as fractured. In the case of non-fractured cores, the WAG injection outperformed continuous gas injection (CGI) and continuous water injection (CWI). As expected, the presence of fractures significantly reduced performance of WAG, CGI and CWI injection modes. In contrast, with regard to FAWAG, deployment of foam flow in the presence of fractures remarkably enhanced oil recovery, which confirms the possibility of using the FAWAG method in situations of premature gas breakthrough. The positive results encourage us to continue the research of the potential uses of this high-nitrogen natural gas in EOR, especially in the view of the utilization of gas reservoirs with advantageous location, high reserves and reservoir energy.

Sign in / Sign up

Export Citation Format

Share Document