Water Saturation (Sw) from Logging-While-Drilling Resistivity, Capture Sigma and Core Analysis for ROS Determination in a Giant Middle East Carbonate Reservoir

2012 ◽  
Author(s):  
Samy Serag El Din ◽  
Chanh Cao Minh ◽  
Douglas R. Murray ◽  
Jacob V. Brahmakulam
Keyword(s):  
Middle East ◽  
Water Saturation ◽  
Carbonate Reservoir ◽  
Core Analysis ◽  
Logging While Drilling

Simulation of Miscible Displacement in Full-Diameter Carbonate Cores

1982 ◽  
Vol 22 (05) ◽  
pp. 647-657 ◽  
Author(s):  
J.P. Batycky ◽  
B.B. Maini ◽  
D.B. Fisher
Keyword(s):  
Oil Recovery ◽  
Water Saturation ◽  
Accurate Determination ◽  
Miscible Displacement ◽  
Carbonate Reservoir ◽  
Core Material ◽  
Immiscible Fluid ◽  
Displacement Efficiency ◽  
Carbonate Cores ◽  
Capacitance Model

Abstract Miscible gas displacement data obtained from full-diameter carbonate reservoir cores have been fitted to a modified miscible flow dispersion-capacitance model. Starting with earlier approaches, we have synthesized an algorithm that provides rapid and accurate determination of the three parameters included in the model: the dispersion coefficient, the flowing fraction of displaceable volume, and the rate constant for mass transfer between flowing and stagnant volumes. Quality of fit is verified with a finite-difference simulation. The dependencies of the three parameters have been evaluated as functions of the displacement velocity and of the water saturation within four carbonate cores composed of various amounts of matrix, vug, and fracture porosity. Numerical simulation of a composite core made by stacking three of the individual cores has been compared with the experimental data. For comparison, an analysis of Berea sandstone gas displacement also has been provided. Although the sandstone displays a minor dependence of gas recovery on water saturation, we found that the carbonate cores are strongly affected by water content. Such behavior would not be measurable if small carbonate samples that can reflect only matrix properties were used. This study therefore represents a significant assessment of the dispersion-capacitance model for carbonate cores and its ability to reflect changes in pore interconnectivity that accompany water saturation alteration. Introduction Miscible displacement processes are used widely in various aspects of oil recovery. A solvent slug injected into a reservoir can be used to displace miscibly either oil or gas. The necessary slug size is determined by the rate at which deterioration can occur as the slug is Another commonly used miscible process involves addition of a small slug within the injected fluids or gases to determine the nature and extent of inter well communication. The quantity of tracer material used is dictated by analytical detection capabilities and by an understanding of the miscible displacement properties of the reservoir. We can develop such understanding by performing one-dimensional (1D) step-change miscible displacement experiments within the laboratory with selected reservoir core material. The effluent profiles derived from the experiments then are fitted to a suitable mathematical model to express the behavior of each rock type through the use of a relatively small number of parameters. This paper illustrates the efficient application of the three-parameter, dispersion-capacitance model. Its application previously has been limited to use with small homogeneous plugs normally composed of intergranular and intencrystalline porosity, and its suitability for use with cores displaying macroscopic heterogeneity has been questioned. Consequently, in addition to illustrating its use with a homogeneous sandstone, we fit data derived from previously reported full-diameter carbonate cores. As noted earlier, these cores were heterogeneous, and each of them displayed different dual or multiple types of porosity characteristic of vugular and fractured carbonate rocks. Dispersion-Capacitance Model The displacement efficiency of one fluid by a second immiscible fluid within a porous medium depends on the complexity of rock and fluid properties. SPEJ P. 647^

Injectivity and Propagation of Sulfonated Acrylamide-Based Copolymers in Low Permeability Carbonate Reservoir Cores in Harsh Salinity and Temperature Conditions : Challenges and Learnings from a Middle East Onshore Case Study

2021 ◽  
Author(s):  
Nicolas Gaillard ◽  
Matthieu Olivaud ◽  
Alain Zaitoun ◽  
Mahmoud Ould-Metidji ◽  
Guillaume Dupuis ◽  
...  
Keyword(s):  
Middle East ◽  
Polymer Solutions ◽  
Carbonate Reservoir ◽  
Core Material ◽  
Low Permeability ◽  
The Core ◽  
Reservoir Conditions ◽  
Carbonate Cores ◽  
The Impact ◽  
Mobility Reduction

Abstract Polymer flooding is one of the most mature EOR technology applied successfully in a broad range of reservoir conditions. The last developments made in polymer chemistries allowed pushing the boundaries of applicability towards higher temperature and salinity carbonate reservoirs. Specifically designed sulfonated acrylamide-based copolymers (SPAM) have been proven to be stable for more than one year at 120°C and are the best candidates to comply with Middle East carbonate reservoir conditions. Numerous studies have shown good injectivity and propagation properties of SPAM in carbonate cores with permeabilities ranging from 70 to 150 mD in presence of oil. This study aims at providing new insights on the propagation of SPAM in carbonate reservoir cores having permeabilities ranging between 10 and 40 mD. Polymer screening was performed in the conditions of ADNOC onshore carbonate reservoir using a 260 g/L TDS synthetic formation brine together with oil and core material from the reservoir. All the experiments were performed at residual oil saturation (Sor). The experimental approach aimed at reproducing the transport of the polymer entering the reservoir from the sand face up to a certain depth. Three reservoir coreflood experiments were performed in series at increasing temperatures and decreasing rates to mimic the progression of the polymer in the reservoir with a radial velocity profile. A polymer solution at 2000 ppm was injected in the first core at 100 mL/h and 40°C. Effluents were collected and injected in the second core at 20 mL/h and 70°C. Effluents were collected again and injected in the third core at 4 mL/h and 120°C. A further innovative approach using reservoir minicores (6 mm length disks) was also implemented to screen the impact of different parameters such as Sor, molecular weight and prefiltration step on the injectivity of the polymer solutions. According to minicores data, shearing of the polymer should help to ensure good propagation and avoid pressure build-up at the core inlet. This result was confirmed through an injection in a larger core at Sor and at 120°C. When comparing the injection of sheared and unsheared polymer at the same concentration, core inlet impairment was suppressed with the sheared polymer and the same range of mobility reduction (Rm) was achieved in the internal section of the core although viscosity was lower for the sheared polymer. Such result indicates that shearing is an efficient way to improve injectivity while maximizing the mobility reduction by suppressing the loss of product by filtration/retention at the core inlet. This paper gives new insights concerning SPAM rheology in low permeability carbonate cores. Additionally, it provides an innovative and easier approach for screening polymer solutions to anticipate their propagation in more advanced coreflooding experiments.

Real-Time EM Look-Ahead Resistivity for Mapping of Oil/Water Contact While Drilling at Low Deviated Well, New Perspective for Mature Oil Fields Development: A Case Study Of Umm Gudair Field, Kuwait

2021 ◽  
Author(s):  
Nasser Faisal Al-Khalifa ◽  
Mohammed Farouk Hassan ◽  
Deepak Joshi ◽  
Asheshwar Tiwary ◽  
Ihsan Taufik Pasaribu ◽  
...  
Keyword(s):  
Water Saturation ◽  
High Water ◽  
Carbonate Reservoir ◽  
Water Contact ◽  
Saturation Zone ◽  
Look Ahead ◽  
Production History ◽  
Oil Water ◽  
High Water Cut ◽  
Water Cut

Abstract The Umm Gudair (UG) Field is a carbonate reservoir of West Kuwait with more than 57 years of production history. The average water cut of the field reached closed to 60 percent due to a long history of production and regulating drawdown in a different part of the field, consequentially undulating the current oil/water contact (COWC). As a result, there is high uncertainty of the current oil/water contact (COWC) that impacts the drilling strategy in the field. The typical approach used to develop the field in the lower part of carbonate is to drill deviated wells to original oil/water contact (OOWC) to know the saturation profile and later cement back up to above the high-water saturation zone and then perforate with standoff. This method has not shown encouraging results, and a high water cut presence remains. An innovative solution is required with a technology that can give a proactive approach while drilling to indicate approaching current oil/water contact and geo-stop drilling to give optimal standoff between the bit and the detected water contact (COWC). Recent development of electromagnetic (EM) look-ahead resistivity technology was considered and first implemented in the Umm Gudair (UG) Field. It is an electromagnetic-based signal that can detect the resistivity features ahead of the bit while drilling and enables proactive decisions to reduce drilling and geological or reservoir risks related to the well placement challenges.

Improving Oil In Place Estimation through an Improve Water Saturation Prediction - A Case Study in the Middle East

2008 ◽  
Author(s):  
Mohamed Al Hammadi ◽  
Shamsa Al Maskari ◽  
El-Sayed Moustafa Radwan
Keyword(s):  
Middle East ◽  
Water Saturation

First microseismic monitoring results for a Middle East carbonate reservoir: Minagish oil field case study, western Kuwait

2008 ◽  
Author(s):  
Emmanuel Gaucher ◽  
Christophe C. Maisons ◽  
Abdullatif Y. Al-Kandari ◽  
Kamal Al-Atroshi and Jassim M. Al-Kanderi
Keyword(s):  
Middle East ◽  
Microseismic Monitoring ◽  
Carbonate Reservoir ◽  
Oil Field ◽  
Field Case
Sign in / Sign up

Export Citation Format

Share Document