Mobility Control for Gas Injection in Heterogeneous Carbonate Reservoirs: Comparison of Foams versus Polymers

Author(s):  
Shehadeh K. Masalmeh ◽  
Lingli Wei ◽  
Carl P.A. Blom
2021 ◽  
Author(s):  
Thaer I. Ismail ◽  
Emad W. Al-Shalabi ◽  
Mahmoud Bedewi ◽  
Waleed AlAmeri

Abstract Gas injection is one of the most commonly used enhanced oil recovery (EOR) methods. However, there are multiple problems associated with gas injection including gravity override, viscous fingering, and channeling. These problems are due to an adverse mobility ratio and cause early breakthrough of the gas resulting, in poor recovery efficiency. A Water Alternating Gas (WAG) injection process is recommended to resolve these problems through better mobility control of gas, leading to better project economics. However, poor WAG design and lack of understanding of the different factors that control its performance might result in unfavorable oil recovery. Therefore, this study provides more insight into improving WAG oil recovery by optimizing different surface and subsurface WAG parameters using a coupled surface and subsurface simulator. Moreover, the work investigates the effects of hysteresis on WAG performance. This case study investigates a field named Volve, which is a decommissioned sandstone field in the North Sea. Experimental design of factors influencing WAG performance on this base case was studied. Sensitivity analysis was performed on different surface and subsurface WAG parameters including WAG ratio, time to start WAG, total gas slug size, cycle slug size, and tubing diameter. A full two-level factorial design was used for the sensitivity study. The significant parameters of interest were further optimized numerically to maximize oil recovery. The results showed that the total slug size is the most important parameter, followed by time to start WAG, and then cycle slug size. WAG ratio appeared in some of the interaction terms while tubing diameter effect was found to be negligible. The study also showed that phase hysteresis has little to no effect on oil recovery. Based on the optimization, it is recommended to perform waterflooding followed by tertiary WAG injection for maximizing oil recovery from the Volve field. Furthermore, miscible WAG injection resulted in an incremental oil recovery between 5 to 11% OOIP compared to conventional waterflooding. WAG optimization is case-dependent and hence, the findings of this study hold only for the studied case, but the workflow should be applicable to any reservoir. Unlike most previous work, this study investigates WAG optimization considering both surface and subsurface parameters using a coupled model.


2021 ◽  
Author(s):  
Siqing Xu ◽  
Ahmed A BinAmro ◽  
Aaesha K. Al Keebali ◽  
Mohamed Baslaib ◽  
Shehadeh Masalmeh

Abstract Miscible CO2 flood is a well-established proven EOR recovery mechanism. There have been a large number of CO2 EOR developments worldwide, in both carbonate and clastic reservoirs. Potential control or influence factors on incremental production and incremental recovery over water flood are well documented in the published literature. Some of the published CO2 EOR developments have reported relatively high incremental recoveries. ADNOC is a leader in miscible gas injection EOR in carbonate reservoirs. There are a number of ongoing miscible gas injection EOR developments within its portfolio contributing a significant amount of production. Miscible CO2 flood is a key EOR development for ADNOC. Following intensive screening studies and laboratory experiments, the first CO2 EOR pilot in the MENA region was conducted as early as 2009 in one of ADNOC Onshore fields. This paved the way for further large-scale deployment and CO2 WAG pilots starting in 2016, both onshore. Appreciable progresses have been made since 2009. This bodes well with the significant initiatives undertaken by the UAE towards carbon emissions and greenhouse gas reduction, climate control and sustainable development. There are broad consensus that climate changes are now and will continue to affect all countries on all continents. Potential global warming can disrupt national economies and adversely impact on lives, costing people, communities and countries already today and perhaps more in the future. Carbon Capture, Utilization, and Storage (CCUS) technologies have been making headlines and attracting increasing amount of renewed attention, because they are in line with meeting global greenhouse gas reduction goals, and contributing towards climate control and sustainable development. The giant Abu Dhabi onshore field consists of 6 carbonate reservoirs. Several pilots, immiscible hydrocarbon gas injection and CO2 WAG, and a pattern immiscible gas injection WAG flood have been executed. Miscible gas injection EOR is therefore field proven. However, due to large field size, surface congestion constraints, geological and fluid variations, miscible gas injection EOR development by reservoir individually becomes complex and economically challenging. This paper presents a comprehensive study and recommends an integrated CCUS Hub development approach - enabling field-wide EOR development with several hundred million-barrels of incremental recovery. The study follows a step-by-step systematic method. Existing water flood performances were assessed first. History matched full field simulation then leads to identification of CO2 EOR targets by area/flank for each reservoir. These are referred to as sweet development areas. Available advanced PVT data were analysed and a multi-reservoir single equation of state developed. It has been found that only CO2 is miscible across all six reservoirs, while hydrocarbon gas is also miscible for the deepest two reservoirs. Dedicated fine scale sector models (EOR history matched where applicable) were developed to generate multiple CO2 EOR development scenarios, for example, depending on water flood maturity at the time of CO2 EOR start-up, and potential impact on incremental oil production, incremental oil recovery due to reservoir heterogeneity. First results from sector modelling show that quite a few areas/flanks would be sub-economical if CO2 EOR development on a stand-alone basis. Hence the concept of a CCUS Hub is proposed, which would allow sweet development areas in any or all of the six reservoirs to be developed from a single common surface Cluster. There is potential space for development phasing, allowing additional CO2 EOR developments within the same cluster area once ullage and CO2 supply becomes available. The CCUS Hub development approach facilitates optimization and sharing of injection/production flow-lines; surface space, gathering and processing facilities, CO2 supply, CO2 recovery unit deployment coupled with produced gas re-injection into the 2 deepest reservoirs. Compared to a more conventional development approach of reservoir by reservoir, considerable scope for CAPEX and OPEX savings was found. Assuming a constant future oil price, a reduction in development costs would allow more sweet development areas to pass the threshold of economical development, leading to an increase in overall incremental production and recovery from CO2 EOR.


2019 ◽  
Author(s):  
Chenji Wei ◽  
Yuhe Wang ◽  
Baozhu Li ◽  
Jingjian Zhang ◽  
Wan Zhang ◽  
...  

SPE Journal ◽  
2018 ◽  
Vol 23 (06) ◽  
pp. 2243-2259 ◽  
Author(s):  
Pengfei Dong ◽  
Maura Puerto ◽  
Guoqing Jian ◽  
Kun Ma ◽  
Khalid Mateen ◽  
...  

Summary Oil recovery in heterogeneous carbonate reservoirs is typically inefficient because of the presence of high-permeability fracture networks and unfavorable capillary forces within the oil-wet matrix. Foam, as a mobility-control agent, has been proposed to mitigate the effect of reservoir heterogeneity by diverting injected fluids from the high-permeability fractured zones into the low-permeability unswept rock matrix, hence improving the sweep efficiency. This paper describes the use of a low-interfacial-tension (low-IFT) foaming formulation to improve oil recovery in highly heterogeneous/fractured oil-wet carbonate reservoirs. This formulation provides both mobility control and oil/water IFT reduction to overcome the unfavorable capillary forces preventing invading fluids from entering an oil-filled matrix. Thus, as expected, the combination of mobility control and low-IFT significantly improves oil recovery compared with either foam or surfactant flooding. A three-component surfactant formulation was tailored using phase-behavior tests with seawater and crude oil from a targeted reservoir. The optimized formulation simultaneously can generate IFT of 10−2 mN/m and strong foam in porous media when oil is present. Foam flooding was investigated in a representative fractured core system, in which a well-defined fracture was created by splitting the core lengthwise and precisely controlling the fracture aperture by applying a specific confining pressure. The foam-flooding experiments reveal that, in an oil-wet fractured Edward Brown dolomite, our low-IFT foaming formulation recovers approximately 72% original oil in place (OOIP), whereas waterflooding recovers only less than 2% OOIP; moreover, the residual oil saturation in the matrix was lowered by more than 20% compared with a foaming formulation lacking a low-IFT property. Coreflood results also indicate that the low-IFT foam diverts primarily the aqueous surfactant solution into the matrix because of (1) mobility reduction caused by foam in the fracture, (2) significantly lower capillary entry pressure for surfactant solution compared with gas, and (3) increasing the water relative permeability in the matrix by decreasing the residual oil. The selective diversion effect of this low-IFT foaming system effectively recovers the trapped oil, which cannot be recovered with single surfactant or high-IFT foaming formulations applied to highly heterogeneous or fractured reservoirs.


2008 ◽  
Vol 23 (02) ◽  
pp. 210-214 ◽  
Author(s):  
AmirMasoud Kalantari-Dahaghi ◽  
Vida Gholami ◽  
Jamshid Moghadasi ◽  
R. Abdi

Sign in / Sign up

Export Citation Format

Share Document