Cumulative Fatigue Damage of Drill Pipe in Dog-Legs

1966 ◽  
Vol 18 (03) ◽  
pp. 359-363 ◽  
Author(s):  
J.E. Hansford ◽  
A. Lubinski
Keyword(s):  
Fatigue Damage ◽  
Drill Pipe ◽  
Cumulative Fatigue Damage

Analysis of Some Factors Related to Permissible Horizontal Motions of a Floating Drilling Vessel

1970 ◽  
Vol 10 (03) ◽  
pp. 229-236 ◽  
Author(s):  
John E. Hansford ◽  
Arthur Lubinski
Keyword(s):  
Fatigue Damage ◽  
Water Depth ◽  
Drill Pipe ◽  
Drill String ◽  
Blowout Preventer ◽  
Bending Stresses ◽  
Cumulative Fatigue Damage ◽  
Vessel Motion ◽  
Pipe Bending ◽  
Rotary Drive

Abstract Horizontal vessel motions (drift, sway or surge) result in the bending of the drill-string members in the vicinity of the rotary-drive bushing at the vessel and at the blowout preventer close to the sea floor. Allowable horizontal vessel motions are calculated as a function of hookload, using both cumulative fatigue damage and drill-pipe strength as criteria for drilling and for pulling stuck pipe. The presently used rule limiting horizontal vessel motion to 5 percent of water depth is shown to be too restrictive in some cases and too lenient in others. Introduction When drilling from a floating vessel, the rotating drill string is subjected to fatigue damage caused by reversing stresses which arise from heave, roll, pitch and horizontal motions of the vessel. In Ref. pitch and horizontal motions of the vessel. In Ref. 1, the effect of drilling-vessel roll and pitch on the cumulative fatigue damage of the kelly and the first joint of drill pipe below the kelly are examined. As a continuation of that investigation, the present study covers the effect of horizontal motions of the vessel on the drill string. Horizontal departure from over the borehole may be oscillatory (sway or surge), static (drift), or most often, some combination of the two. An accepted limit of horizontal vessel motion of 5 percent of the water depth has been suggested mad percent of the water depth has been suggested mad frequently followed. In reality, the allowable motion is strongly influenced by the hookload. Motions greater than 5 percent of water depth are often permissible, and under some conditions, motions permissible, and under some conditions, motions should be limited to less than 5 percent of water depth. The purpose of this paper is to suggest maximum permissible motions imposed by drill-pipe fatigue damage and pipe strength, as a function of hookload. IDEALIZED SYSTEMS Fig. 1 shows an idealized system, highly exaggerated for explicitness. Although pipe bends are shown quite acute, bending stresses were properly defined mathematically. The pipe bending properly defined mathematically. The pipe bending at the rotary-drive bushing (labeled RDB in Fig. 1) is relieved in most cases by a gimbaled bushing and largely taken by the kelly, a more durable member. Therefore, the point of most severe damage is in the area of the blowout preventer rams (labeled BOP). SPEJ P. 229

A Comparison of Fracture Mechanics and S–N Curve Approaches in Designing Drill Pipe

1992 ◽  
Vol 114 (3) ◽  
pp. 205-211 ◽  
Author(s):  
A. Ertas ◽  
G. Mustafa ◽  
O. Cuvalci
Keyword(s):  
Fracture Mechanics ◽  
Fatigue Damage ◽  
Drill Pipe ◽  
Ball Joint ◽  
Marine Riser ◽  
Deep Drilling ◽  
Miner’S Rule ◽  
Miner's Rule ◽  
Total Damage ◽  
Dynamic Fatigue

It is well known that the upper ball joint in a marine riser, in deep drilling, can cause fatigue damage in the drill pipe passing through it. A study of fracture mechanics and S–N curve approaches has been undertaken to determine the dynamic fatigue damage in the drill pipe. Miner’s rule is utilized in both methods to determine the total damage. The results of both methods are compared.

Fatigue Life Assessment of Crane Reel

2011 ◽  
Vol 383-390 ◽  
pp. 2941-2944
Author(s):  
Wei Ming Du ◽  
Fei Xue
Keyword(s):  
Finite Element Method ◽  
Fatigue Life ◽  
Fatigue Damage ◽  
Residual Life ◽  
Life Assessment ◽  
Life Estimation ◽  
Fatigue Life Assessment ◽  
Weld Fatigue ◽  
Simulation Results ◽  
Cumulative Fatigue Damage

The crane reel is generally manufactured by section welding method when the diameter is over 380mm. With the cumulative fatigue damage principle which is based on stress S-N curve, the fatigue damage of one crane reel is analyzed by finite element method, the reel weld fatigue strength and fatigue life are calculated, and the simulation results are proved to be reliable. This method provides an efficient reference for crane reel design and residual life estimation.

Sign in / Sign up

Export Citation Format

Share Document