Infilling Method of Well Pattern Suitable to Imbibition Oil Recovery for Fractured and Extra Lower Permeability Oil Reservoirs in Daqing Oilfield

2006 ◽  
Author(s):  
Lin Li ◽  
Bingyu Ji ◽  
Baowen Cui ◽  
Xisheng Zhou ◽  
Min Li Li ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Oil Reservoirs ◽  
Well Pattern ◽  
Lower Permeability

The Mechanism of Flue Gas Injection for Enhanced Light Oil Recovery

2004 ◽  
Vol 126 (2) ◽  
pp. 119-124 ◽  
Author(s):  
O. S. Shokoya ◽  
S. A. (Raj) Mehta ◽  
R. G. Moore ◽  
B. B. Maini ◽  
M. Pooladi-Darvish ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Flue Gas ◽  
Gas Injection ◽  
Cost Effective ◽  
Air Injection ◽  
Oil Reservoirs ◽  
Flue Gases ◽  
Low Permeability ◽  
Light Oil ◽  
Light Oil Reservoirs

Flue gas injection into light oil reservoirs could be a cost-effective gas displacement method for enhanced oil recovery, especially in low porosity and low permeability reservoirs. The flue gas could be generated in situ as obtained from the spontaneous ignition of oil when air is injected into a high temperature reservoir, or injected directly into the reservoir from some surface source. When operating at high pressures commonly found in deep light oil reservoirs, the flue gas may become miscible or near–miscible with the reservoir oil, thereby displacing it more efficiently than an immiscible gas flood. Some successful high pressure air injection (HPAI) projects have been reported in low permeability and low porosity light oil reservoirs. Spontaneous oil ignition was reported in some of these projects, at least from laboratory experiments; however, the mechanism by which the generated flue gas displaces the oil has not been discussed in clear terms in the literature. An experimental investigation was carried out to study the mechanism by which flue gases displace light oil at a reservoir temperature of 116°C and typical reservoir pressures ranging from 27.63 MPa to 46.06 MPa. The results showed that the flue gases displaced the oil in a forward contacting process resembling a combined vaporizing and condensing multi-contact gas drive mechanism. The flue gases also became near-miscible with the oil at elevated pressures, an indication that high pressure flue gas (or air) injection is a cost-effective process for enhanced recovery of light oils, compared to rich gas or water injection, with the potential of sequestering carbon dioxide, a greenhouse gas.

Can unmixed complex forming polymer surfactant formulations be injected into oil reservoirs or aquifers without clogging them?

Soft Matter ◽  
2021 ◽  
Author(s):  
Massinissa Hamouna ◽  
Aline Delbos ◽  
Christine Dalmazonne ◽  
Annie Colin
Keyword(s):  
Enhanced Oil Recovery ◽  
Soil Remediation ◽  
Oil Recovery ◽  
Oil Reservoirs ◽  
Polymer Surfactant

In the context of enhanced oil recovery or soil remediation, we study the role of interactions between polymers and surfactants on the injectivity of formulations containing mixtures of polymers and...

scholarly journals Effect of Non-Newtonian Flow on Polymer Flooding in Heavy Oil Reservoirs

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1225 ◽  
Author(s):  
Xiankang Xin ◽  
Gaoming Yu ◽  
Zhangxin Chen ◽  
Keliu Wu ◽  
Xiaohu Dong ◽  
...  
Keyword(s):  
Porous Media ◽  
Polymer Solution ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Flow Behavior ◽  
Polymer Flooding ◽  
Oil Reservoirs ◽  
Flow In Porous Media ◽  
Newtonian Flow ◽  
Heavy Oil Reservoirs

The flow of polymer solution and heavy oil in porous media is critical for polymer flooding in heavy oil reservoirs because it significantly determines the polymer enhanced oil recovery (EOR) and polymer flooding efficiency in heavy oil reservoirs. In this paper, physical experiments and numerical simulations were both applied to investigate the flow of partially hydrolyzed polyacrylamide (HPAM) solution and heavy oil, and their effects on polymer flooding in heavy oil reservoirs. First, physical experiments determined the rheology of the polymer solution and heavy oil and their flow in porous media. Then, a new mathematical model was proposed, and an in-house three-dimensional (3D) two-phase polymer flooding simulator was designed considering the non-Newtonian flow. The designed simulator was validated by comparing its results with those obtained from commercial software and typical polymer flooding experiments. The developed simulator was further applied to investigate the non-Newtonian flow in polymer flooding. The experimental results demonstrated that the flow behavior index of the polymer solution is 0.3655, showing a shear thinning; and heavy oil is a type of Bingham fluid that overcomes a threshold pressure gradient (TPG) to flow in porous media. Furthermore, the validation of the designed simulator was confirmed to possess high accuracy and reliability. According to its simulation results, the decreases of 1.66% and 2.49% in oil recovery are caused by the difference between 0.18 and 1 in the polymer solution flow behavior indexes of the pure polymer flooding (PPF) and typical polymer flooding (TPF), respectively. Moreover, for heavy oil, considering a TPG of 20 times greater than its original value, the oil recoveries of PPF and TPF are reduced by 0.01% and 5.77%, respectively. Furthermore, the combined effect of shear thinning and a threshold pressure gradient results in a greater decrease in oil recovery, with 1.74% and 8.35% for PPF and TPF, respectively. Thus, the non-Newtonian flow has a hugely adverse impact on the performance of polymer flooding in heavy oil reservoirs.

Sign in / Sign up

Export Citation Format

Share Document