Determination of the Drainage Area of Horizontal Wells in the Presence of Vertical Wells: Effect of Reservoir and Well Parameters

2001 ◽  
Vol 40 (10) ◽  
Author(s):  
A. Abdelgawad ◽  
D. Malekzadeh
Keyword(s):  
Horizontal Wells ◽  
Drainage Area ◽  
Vertical Wells

Determination of well spacing volumetric factor for assessment of final oil recovery in reservoirs developed by horizontal wells

2021 ◽  
pp. 47-53
Author(s):  
I.N. Khakimzyanov ◽  
◽  
V.Sh. Mukhametshin ◽  
R.N. Bakhtizin ◽  
R.I. Sheshdirov ◽  
...  
Keyword(s):  
Inclination Angle ◽  
Oil Recovery ◽  
Horizontal Wells ◽  
Drainage Area ◽  
Well Spacing ◽  
Volumetric Determination ◽  
Fluid Inflow

The formula for determination of volumetric factor of well spacing for assessment of final oil recovery in reservoirs developed by horizontal wells is offered. For the purpose of comparison of well spacing calculated using conventional and volumetric techniques, twelve development options of the pilot area of the Yamashinskoye field with variousplacement of vertical and horizontal wells were considered. By results of calculations, marked difference in values of well spacing was observed testifying that the conventional formula used to calculate well spacing does not consider the volume nature of fluid inflow to wells with one or more horizontal laterals. The offered technique of volumetric determination of well spacing through the inclination angle, the radius of well drainage area, and the length of a lateral considers the volumetric nature of inflow to horizontal multilateral wells.

Interdisciplinary Approach for Wellbore Stability During Slimhole Drilling at Volga-Urals Basin Oilfield

2021 ◽  
Author(s):  
Anna Vladimirovna Norkina ◽  
Sergey Mihailovich Karpukhin ◽  
Konstantin Urjevich Ruban ◽  
Yuriy Anatoljevich Petrakov ◽  
Alexey Evgenjevich Sobolev
Keyword(s):  
Drilling Fluid ◽  
Interdisciplinary Approach ◽  
Wellbore Stability ◽  
Vertical Wells ◽  
Wellbore Instability ◽  
Water Based ◽  
Chemical Studies ◽  
Fluid Rheology ◽  
Selection Of

Abstract The design features and the need to use a water-based solution make the task of ensuring trouble-free drilling of vertical wells non-trivial. This work is an example of an interdisciplinary approach to the analysis of the mechanisms of instability of the wellbore. Instability can be caused by a complex of reasons, in this case, standard geomechanical calculations are not enough to solve the problem. Engineering calculations and laboratory chemical studies are integrated into the process of geomechanical modeling. The recommendations developed in all three areas are interdependent and inseparable from each other. To achieve good results, it is necessary to comply with a set of measures at the same time. The key tasks of the project were: determination of drilling density, tripping the pipe conditions, parameters of the drilling fluid rheology, selection of a system for the best inhibition of clay swelling.

Improving Proppant Placement Success in Horizontal Wells in Layered Reservoirs in the Sultanate of Oman

2021 ◽  
Author(s):  
Andrew Boucher ◽  
Josef Shaoul ◽  
Inna Tkachuk ◽  
Mohammed Rashdi ◽  
Khalfan Bahri ◽  
...  
Keyword(s):  
Horizontal Well ◽  
Complex Geometry ◽  
Horizontal Wells ◽  
Vertical Position ◽  
Sultanate Of Oman ◽  
Vertical Wells ◽  
Multiple Fractures ◽  
Initiation Point ◽  
Interval Selection ◽  
Geological Units

Abstract A gas condensate field in the Sultanate of Oman has been developed since 1999 with vertical wells, with multiple fractures targeting different geological units. There were always issues with premature screenouts, especially when 16/30 or 12/20 proppant were used. The problems placing proppant were mainly in the upper two units, which have the lowest permeability and the most heterogeneous lithology, with alternating sand and shaly layers between the thick competent heterolith layers. Since 2015, a horizontal well pilot has been under way to determine if horizontal wells could be used for infill drilling, focusing on the least depleted units at the top of the reservoir. The horizontal wells have been plagued with problems of high fracturing pressures, low injectivity and premature screenouts. This paper describes a comprehensive analysis performed to understand the reasons for these difficulties and to determine how to improve the perforation interval selection criteria and treatment approach to minimize these problems in future horizontal wells. The method for improving the success rate of propped fracturing was based on analyzing all treatments performed in the first seven horizontal wells, and categorizing their proppant placement behavior into one of three categories (easy, difficult, impossible) based on injectivity, net pressure trend, proppant pumped and screenout occurrence. The stages in all three categories were then compared with relevant parameters, until a relationship was found that could explain both the successful and unsuccessful treatments. Treatments from offset vertical wells performed in the same geological units were re-analyzed, and used to better understand the behavior seen in the horizontal wells. The first observation was that proppant placement challenges and associated fracturing behavior were also seen in vertical wells in the two uppermost units, although to a much lesser extent. A strong correlation was found in the horizontal well fractures between the problems and the location of the perforated interval vertically within this heterogeneous reservoir. In order to place proppant successfully, it was necessary to initiate the fracture in a clean sand layer with sufficient vertical distance (TVT) to the heterolith (barrier) layers above and below the initiation point. The thickness of the heterolith layers was also important. Without sufficient "room" to grow vertically from where it initiates, the fracture appears to generate complex geometry, including horizontal fracture components that result in high fracturing pressures, large tortuosity friction, limited height growth and even poroelastic stress increase. This study has resulted in a better understanding of mechanisms that can make hydraulic fracturing more difficult in a horizontal well than a vertical well in a laminated heterogeneous low permeability reservoir. The guidelines given on how to select perforated intervals based on vertical position in the reservoir, rather than their position along the horizontal well, is a different approach than what is commonly used for horizontal well perforation interval selection.

scholarly journals Mathematical description of a bounded oil reservoir with a horizontal well

2021 ◽  
Vol 2 (1) ◽  
pp. 67-76
Author(s):  
T. N. Nzomo ◽  
S. E Adewole ◽  
K. O Awuor ◽  
D. O. Oyoo
Keyword(s):  
Pressure Distribution ◽  
Effective Permeability ◽  
Horizontal Well ◽  
Horizontal Wells ◽  
Oil Reservoir ◽  
Vertical Wells ◽  
Anisotropic Permeability ◽  
Time Approximation ◽  
Reservoir Geometry ◽  
Short Time

Horizontal wells are more productive compared to vertical wells if their performance is optimized. For a completely bounded oil reservoir, immediately the well is put into production, the boundaries of the oil reservoir have no effect on the flow. The pressure distribution thus can be approximated with this into consideration. When the flow reaches either the vertical or the horizontal boundaries of the reservoir, the effect of the boundaries can be factored into the pressure distribution approximation. In this paper we consider the above cases and present a detailed mathematical model that can be used for short time approximation of the pressure distribution for a horizontal well with sealed boundaries. The models are developed using appropriate Green’s and source functions. In all the models developed the effect of the oil reservoir boundaries as well as the oil reservoir parameters determine the flow period experienced. In particular, the effective permeability relative to horizontal anisotropic permeability, the width and length of the reservoir influence the pressure response. The models developed can be used to approximate and analyze the pressure distribution for horizontal wells during a short time of production. The models presented show that the dimensionless pressure distribution is affected by the oil reservoir geometry and the respective directional permeabilities.

Geomechanical Approach in Classification of Borehole Failures in Fractured Carbonates of Boca De Jaruco Field

2021 ◽  
Author(s):  
Anna Vladimirovna Norkina ◽  
Iaroslav Olegovich Simakov ◽  
Yuriy Anatoljevich Petrakov ◽  
Alexey Evgenjevich Sobolev ◽  
Oleg Vladimirovich Petrashov ◽  
...  
Keyword(s):  
Stress State ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
Vertical Wells ◽  
Stress Regime ◽  
Geophysical Information ◽  
The Republic ◽  
Maximum Horizontal Stress

Abstract This article is a continuation of the work on geomechanically calculations for optimizing the drilling of horizontal wells into the productive reservoir M at the Boca de Haruco field of the Republic of Cuba, presented in the article SPE-196897. As part of the work, an assessment of the stress state and direction was carried out using geological and geophysical information, an analysis of the pressure behavior during steam injections, cross-dipole acoustics, as well as oriented caliper data in vertical wells. After the completion of the first part of the work, the first horizontal wells were successfully drilled into the M formation. According to the recommendations, additional studies were carried out: core sampling and recording of micro-imager logging in the deviated sections. Presence of wellbore failures at the inclined sections allowed to use the method of inverse in-situ stress modeling based on image logs interpretation. The classification of wellbore failures by micro-imager logging: natural origin and violations of technogenic genesis is carried out. The type of breakout is defined. The result of the work was the determination of the stress state and horizontal stresses direction. In addition, the article is supplemented with the calculation of the maximum horizontal stress through the stress regime identifier factor.

Sign in / Sign up

Export Citation Format

Share Document