Fibers and Matrix Constituting (Strain Hardening Cement Composites)High Performance Fiber Reinforced Concrete

2013 ◽  
Vol 69 (4) ◽  
pp. P_105-P_108
Author(s):  
TAKATSUNE KIKUTA ◽  
HIROZO MIHASHI ◽  
HIDEKI HOSHIRO
Keyword(s):  
Reinforced Concrete ◽  
Strain Hardening ◽  
High Performance ◽  
Fiber Reinforced Concrete ◽  
Cement Composites ◽  
Fiber Reinforced ◽  
High Performance Fiber

scholarly journals Implementation of Highly-Flowable Strain Hardening Fiber Reinforced Concrete in New RC Beam-Column Joints

2018 ◽  
Vol 147 ◽  
pp. 01003
Author(s):  
Wen-Cheng Liao ◽  
Wei-Ru Su
Keyword(s):  
Reinforced Concrete ◽  
Strain Hardening ◽  
Life Cycle Cost ◽  
High Performance ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Building Systems ◽  
Rc Building ◽  
High Performance Fiber

The purpose of New RC project was aimed to reduce the member sections and increase the available space of high rise buildings by using high strength concrete (f’c > 70 MPa) and high strength rebars (fy > 685 MPa). Material consumptions and member section sizes can be further reduced owing to the upgrade of strength. However, the nature of brittleness of high strength may also cause early cover spalling and other ductility issues. Addition of steel fibers is an alternative as transverse reinforcement. Highly flowable strain hardening fiber reinforced concrete (HF-SHFRC) has excellent workability in the fresh state and exhibits the strain-hardening and multiple cracking characteristics of high performance fiber reinforced cementitious composites (HPFRCC) in their hardened state. The objective of this study is to investigate the feasibility of implementing HF-SHFRC in New RC building systems, particularly for beam-column joints as an alternative of transverse reinforcements. Four full-scale exterior beam-column joints, including two specimens with intensive transverse reinforcements and two specimens made of HF-SHFRC without any stirrup, are tested. Test results show that the HF-SHFRC specimens perform as well as specimens with intensive transverse reinforcements regarding failure mode, ductility, energy dissipation and crack width control. Integration of New RC building systems and HF-SHFRC can assuring construction qualities and further diminish labor work and give infrastructure longer service life, and eventually lower the life-cycle cost.

scholarly journals Probabilistic Analysis for Strain-Hardening Behavior of High-Performance Fiber-Reinforced Concrete

Materials ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2399 ◽  
Author(s):  
Seung-Won Choi ◽  
Jongkwon Choi ◽  
Seong-Cheol Lee
Keyword(s):  
Reinforced Concrete ◽  
Strain Hardening ◽  
High Performance ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Probable Number ◽  
Hardening Behavior ◽  
Pull Out ◽  
High Performance Fiber ◽  
Strain Hardening Behavior

The practical application of fiber-reinforced concrete (FRC) in structural components has gained growing interest due to structural advantages such as improved tensile strength, distributed load transfer, crack width control, as well as superior durability. To this end, reliable structural assessment techniques and analytical models have been developed, placing emphasis on tension-softening behavior owing to the bond and pull-out mechanisms of fibers at a local crack. However, these models could not be directly applicable to evaluate the multiple cracking mechanisms of high-performance fiber-reinforced concrete (HPFRC), which exhibits strain-hardening behavior. To overcome this challenge, this paper presents a probabilistic analytical technique. This approach has employed the simplified diverse embedment model (SDEM). Then, an HPFRC member was modeled with multiple segments considering the most probable number of cracks. It was assumed that material properties had a normal probability distribution and were randomly assigned to each segment. To have reliable results, 10,000 analyses were performed for each analysis case and validated using experimental test data. Based on the analysis results, the actual strain-hardening tensile behavior of an HPFRC member could be reasonably predicted with the number of segments chosen on the basis of the fiber length.

Influence of technological factors on the properties of ultra-high-performance fiber reinforced concrete

2020 ◽  
pp. 135-147
Author(s):  
Igor Chilin ◽  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Technological Factors ◽  
High Performance Fiber

Приведены результаты исследований и выполнена оценка влияния технологических факторов на реологические свойства самоуплотняющихся сталефибробетонных смесей, определены кратковременные и длительные физико-механические и деформативные характеристики сверхвысокопрочного сталефибробетона, включая определение его фактической морозостойкости.

scholarly journals Resistance of an Optimized Ultra-High Performance Fiber Reinforced Concrete to Projectile Impact

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 63
Author(s):  
Anna L. Mina ◽  
Michael F. Petrou ◽  
Konstantinos G. Trezos
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Depth Of Penetration ◽  
Projectile Impact ◽  
High Performance Fiber

The scope of this paper is to investigate the performance of ultra-high performance fiber reinforced concrete (UHPFRC) concrete slabs, under projectile impact. Mixture performance under impact loading was examined using bullets with 7.62 mm diameter and initial velocity 800 m/s. The UHPFRC, used in this study, consists of a combination of steel fibers of two lengths: 6 mm and 13 mm with the same diameter of 0.16 mm. Six composition mixtures were tested, four UHPFRC, one ultra-high performance concrete (UHPC), without steel fibers, and high strength concrete (HSC). Slabs with thicknesses of 15, 30, 50, and 70 mm were produced and subjected to real shotgun fire in the field. Penetration depth, material volume loss, and crater diameter were measured and analyzed. The test results show that the mixture with a combination of 3% 6 mm and 3% of 13 mm length of steel fibers exhibited the best resistance to projectile impact and only the slabs with 15 mm thickness had perforation. Empirical models that predict the depth of penetration were compared with the experimental results. This material can be used as an overlay to buildings or to construct small precast structures.

Sign in / Sign up

Export Citation Format

Share Document