scholarly journals THE ESTIMATION OF BIREFRINGENCE IN POLYPROPYLENE MELT SPINNING PROCESS

1973 ◽  
Vol 29 (5) ◽  
pp. T205-T210 ◽  
Author(s):  
Jiro Shimizu ◽  
Kozo Shimazaki
Keyword(s):  
Melt Spinning ◽  
Spinning Process ◽  
Polypropylene Melt

Optimization of Manufacturing Parameters for Melt Spun Yarns Using Taguchi Method

2014 ◽  
Vol 556-562 ◽  
pp. 4264-4267
Author(s):  
Shu Wen Wang ◽  
Te Li Su
Keyword(s):  
Taguchi Method ◽  
Melt Spinning ◽  
Parameter Design ◽  
Controllable Factors ◽  
Melt Spun ◽  
Spun Yarns ◽  
Spinning Process ◽  
Polypropylene Melt ◽  
Manufacturing Parameters

In melt spinning process, evenness of polypropylene melt spun yarns affects the appearance, hairiness, strength and productivity of yarns, as well as product production and profits, causing rejection due to nonconformity. The research is to find optimal manufacturing parameters of melt spun yarns. Firstly, to proceed the parameter design by Taguchi method, then to select a manufacturing parameter which will affect the quality of melt spun yarns as controllable factors. Also to choose a suitable orthogonal arrays. Meanwhile, according to variation of analysis, to decide optimal manufacturing parameters of melt spun yarns and its remarkable factor. Finally, using 95% confidence interval to proof the experiment’s reliability and repeatability.

Effect of Crucible Parameters on Planar Flow Melt Spinning Process

2015 ◽  
Vol 68 (6) ◽  
pp. 1125-1129 ◽  
Author(s):  
M. Swaroopa ◽  
L. Venu Gopal ◽  
T. Kishen Kumar Reddy ◽  
B. Majumdar
Keyword(s):  
Melt Spinning ◽  
Planar Flow ◽  
Spinning Process

PLA/Carbon Nanotubes Multifilament Yarns for Relative Humidity Textile Sensor

2011 ◽  
Vol 6 (3) ◽  
pp. 155892501100600 ◽  
Author(s):  
Eric Devaux ◽  
Carole Aubry ◽  
Christine Campagne ◽  
Maryline Rochery
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Relative Humidity ◽  
Melt Spinning ◽  
Flexible Sensor ◽  
Spinning Process ◽  
Textile Sensor ◽  
Multifilament Yarns

Polylactide (PLA) was mixed with 4 wt.% of carbon nanotubes (CNTs) to produce electrical conductive multifilament yarns by melt spinning process for humidity detection. Thanks to a variation of electrical conductivity, this flexible sensor could detect the moisture presence. The introduction of plasticizer was necessary to ensure higher fluidity and drawability of the blend during the spinning process. The plasticizer modifies the crystallinity and the mechanical properties of the yarns. The effectiveness of this sensor (PLA/4 wt.% CNTs fibres) sensitive to humidity, is optimal when the spinning conditions are adapted. In this way, the temperature and the rate of the drawing roll were reduced. The influence of these parameters on the crystallinity, the mechanical properties and the sensitivity of the yarns were studied. Once the appropriate spinning conditions found, one humidity sensitive yarn was processed and the repeatability and efficient reversibility of its sensitivity were highlighted.

Study on the equivalent luminance of luminous fibers in photopic vision and scotopic vision

2017 ◽  
Vol 88 (10) ◽  
pp. 1157-1163 ◽  
Author(s):  
Yanhong Yan ◽  
Chengxia Liu ◽  
Xiaojun Ding
Keyword(s):  
Experimental Data ◽  
Rare Earth ◽  
Melt Spinning ◽  
Emission Spectra ◽  
Scotopic Vision ◽  
Photopic Vision ◽  
Earth Material ◽  
Long Afterglow ◽  
Polyamide Fiber ◽  
Spinning Process

Colored luminous fibers were prepared by a melt spinning process, adding colored pigments and long afterglow rare earth material into polyamide fiber. The colored luminous fibers had a variety of colors in photopic vision, and emitted colored light in mesopic vision and scotopic vision. Based on the experimental data of the emission spectra and the test luminance of the luminous fibers, the effect of the emissive colors of the luminous fibers on the equivalent luminance at different vision states was analyzed. The results showed that the effect of the emissive colors of white, red, yellow, and green luminous fibers on the equivalent luminance was not obvious in photopic and scotopic vision, but that of blue luminous fiber was obvious in photopic vision but not in scotopic vision.

Microstructure Analysis of Melt-Spun Al3Ti Intermetallics by XRD and EXAFS

1996 ◽  
Vol 460 ◽  
Author(s):  
Jinmin Chen ◽  
W. E. Frazier ◽  
E. V. Barrera
Keyword(s):  
Crystal Structure ◽  
High Temperature ◽  
Melt Spinning ◽  
Composition Range ◽  
Processing Parameters ◽  
Wheel Speed ◽  
Annealing Temperatures ◽  
Melt Spun ◽  
Temperature Heat ◽  
Spinning Process

ABSTRACTIn an effort to expand the composition range over which Al3Ti is stable, various amounts of niobium were substituted for titanium and processed by melt-spinning. Several samples were annealed both at 600°C and 1000°C for 24 hours. The effects of processing parameters such as wheel speed, the amount of niobium, and annealing temperatures on the structure were investigated by XRD and EXAFS. XRD showed that for all the samples the only structure present was DO22-The DO22 structure was stable even after the high temperature heat treatments. By means of EXAFS, niobium atoms were observed to occupy titanium sites in the DO22 structure. Furthermore, in the unannealed samples, increasing wheel speed of the melt spinning process or the niobium concentration tended to distort the crystal structure. It was observed that Ti EXAFS had different results from the Nb EXAFS beyond their occupying similar sites, which suggested there may exist some composition zones, i.e. rich Nb zone or rich Ti zones, although the structures present were still DO22. The samples were found to experience different distortions as a function of annealing temperatures.

Sign in / Sign up

Export Citation Format

Share Document