Application of Hydraulic Flushing in Coal Seams To Reduce Hazardous Outbursts in the Mengjin Mine, China

2018 ◽  
Vol 24 (4) ◽  
pp. 425-440 ◽  
Author(s):  
Jingyu Jiang ◽  
Weihua Yang ◽  
Yuanping Cheng ◽  
Baomin Lv ◽  
Kai Zhang ◽  
...  
Keyword(s):  
Field Test ◽  
Coalbed Methane ◽  
Gas Flow ◽  
Average Diameter ◽  
Gas Production ◽  
Hard Coal ◽  
Gas Extraction ◽  
Coal Seams ◽  
Influence Radius ◽  
Borehole Camera

Abstract Hydraulic fracturing and waterjet slotting fracturing have been demonstrated to be effective in creating artificial fractures and stimulating gas production in hard coal seams. However, these methods are inefficient for soft-outburst coal seams because these created fractures are short and easy to close. To eliminate the outburst risk of soft coals, a novel enhanced coalbed methane under-panel cross-strata drainage technique via hydraulic flushing was proposed in this work. The hydraulic flushing effects of boreholes of different sizes in the coal seam were also pre-evaluated by a simulation approach. The modeling results indicate that as the radius of the borehole increases, the plastic and stress-decreasing zone expands. A field test was also conducted in the Minjin mine, China, that investigated the gas pressure variation between three monitoring boreholes at different distances from a hydraulic flushing borehole. Test results indicate that the effective influence radius of gas extraction is approximately 5.5 m. Based on the results of the field test and borehole camera observation, the unloaded coal quantity and the average diameter of the boreholes were estimated to be 8.0 t and 942 mm, respectively. The borehole diameter expanded up to 10 times larger than its original size. The average gas extraction concentration and gas flow rate increased by approximately 2 and 3.5 times, respectively, demonstrating the effectiveness of the proposed hydraulic flushing in improving the gas extraction efficiency. The hydraulic flushing technique therefore is proved to be efficient in eliminating the outburst risk of coal and reducing greenhouse gas emissions.

COAL SEAM DEGASIFICATION IN QUEENSLAND UTILISING HYDRAULIC FRACTURING WITH FOAM—A CASE HISTORY

1981 ◽  
Vol 21 (1) ◽  
pp. 137
Author(s):  
B. Wilkinson ◽  
L. Barro
Keyword(s):  
Gas Flow ◽  
Gas Production ◽  
Low Permeability ◽  
Gas Flow Rate ◽  
Coal Seams ◽  
Flow Rates ◽  
Coal Deposits ◽  
Early Production ◽  
Design Calculations ◽  
Gas Bearing

Vast reserves of gas-bearing coal deposits are located in Queensland. Owing to the extremely low permeability and porosity of the coal, very low gas flow rates are normally encountered. In an effort to enhance the gas production to economic quantities and to degasify the coal to provide a safer mining environment, four experimental wells were drilled into coal seams near Blackwater, Queensland.Based on extensive laboratory testing of coal samples, computerised fracture design calculations were performed to determine a suitable stimulation programme. The wells were hydraulically fractured with up to 15 000 US gal of foamed stimulation fluid containing 75 per cent nitrogen. To prop open the induced fracture system, 15 000 lb of sand was pumped with the foam. The maximum concentration was eight pounds of 20-40 mesh sand per gallon of fluid. Gas production from the unstimulated wells was too low to measure. Early production data soon after the fracturing suggested a gas flow rate of approximately 50 Mcf/D.

scholarly journals Research on the Effective Influence Radius of Hydraulic Reaming in Mining Seam

2015 ◽  
Vol 8 (1) ◽  
pp. 161-167
Author(s):  
Li Peng ◽  
Wang Kai ◽  
Li Bo ◽  
Jiang Yifeng ◽  
Gou Jianqiang
Keyword(s):  
Gas Flow ◽  
Coupling Model ◽  
Field Investigation ◽  
Coal Mass ◽  
Gas Content ◽  
Coal Seams ◽  
Gas Drainage ◽  
Permeability Increase ◽  
Influence Radius ◽  
Drainage Effect

In Accordance with the present situations suggesting that the construction of the gas drainage boreholes in mining seam is sufficient and the gas drainage effect in low permeability coal seams does not yield perfectly, the hydraulic reaming technology in mining seam was proposed to increase the gas drainage efficiency. Through the gas flow method, the effective influence radius of hydraulic reaming was determined and the fluid-solid coupling model of gas drainage along boreholes after hydraulic reaming was established theoretically. Following this, the changes in the laws of gas content around the boreholes in the coal seam were simulated and analyzed. The results indicated that hydraulic reaming can effectively promote the stress-relief and permeability-increase of the coal mass around the boreholes, and the coal mass around the reaming boreholes can be divided into gas flow increase zone, gas flow delay attenuation zone and fast decay zone. The effective influence radius of hydraulic reaming was 5.5~6 m. The obtained simulation results were basically in accordance with the field investigation.

scholarly journals Fracture evolution and gas transport laws of coal and rock in one kilometer deep coal mine with complicated conditions

2019 ◽  
Vol 23 (Suppl. 3) ◽  
pp. 907-915
Author(s):  
Jianguo Zhang ◽  
Man Wang ◽  
Yingwei Wang
Keyword(s):  
Coal Seam ◽  
Coal Mining ◽  
Coal Mine ◽  
Fracture Zone ◽  
Gas Flow ◽  
Gas Transport ◽  
Enhancement Effect ◽  
Gas Extraction ◽  
Coal Seams ◽  
Long Distance

As coal mining gradually extends deeper, coal seams in China generally show high stress, high gas pressure and low permeability, bringing more difficulty to coal mining. Therefore, in order to strengthen gas extraction, it is necessary to carry out reservoir reconstruction after deep coal seams reached. In this paper, the distribution and evolution laws of fracture zone overlaying strata of J15 seam in Pingdingshan No. 10 coal mine after excavation were studied by combining similar simulation and numerical simulation, meanwhile, the gas transport law within fracture zone was numerically simulated. The results show that the fracture zone reaches a maximum of 350 mm in the vertical direction and is 75 mm away from W9,10 coal seams in vertical distance. Since W9,10 coal seams are in an area greatly affected by the bending zone of J15 coal seam under the influence of mining, the mining of J15 coal seam will exert a strong permeability enhancement effect on W9,10 coal seams. The J15 coal seam can act as a long-distance protective layer of W9,10 coal seams to eliminate the outburst danger of the long-distance coal seams in bending zone with coal and gas outburst danger, thereby achiev?ing safe, productive and efficient integrated mining of coal and gas resources. The gas flux of mining-induced fractures in the trapezoidal stage of mining-induced fracture field is far greater than that in the overlaying stratum matrix. The horizontal separation fractures and vertical broken fractures within the mining-induced fracture field act as passages for gas-flow. Compared with gas transport in the overlaying stratum matrix, the horizontal separation fractures and vertical broken fractures within the mining-induced fracture field play a role in guiding gas-flow. The research results can provide theoretical support for the arrangement of high-level gas extraction boreholes in roof fracture zones.

scholarly journals Investigation on the CBM Extraction Techniques in the Broken-Soft and Low-Permeability Coal Seams in Zhaozhuang Coalmine

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Zhaoying Chen ◽  
Xuehai Fu ◽  
Guofu Li ◽  
Jian Shen ◽  
Qingling Tian ◽  
...  
Keyword(s):  
Coal Seam ◽  
Hydraulic Fracturing ◽  
Coalbed Methane ◽  
Research Result ◽  
Horizontal Stress ◽  
Gas Production ◽  
Vertical Stress ◽  
Low Permeability ◽  
Coal Seams

To enhance the coalbed methane (CBM) extraction in broken-soft coal seams, a method of drilling a horizontal well along the roof to hydraulically fracture the coal seam is studied (i.e., HWR-HFC method). We first tested the physical and mechanical properties of the broken-soft and low-permeability (BSLP) coal resourced from Zhaozhuang coalmine. Afterward, the in situ hydraulic fracturing test was conducted in the No. 3 coal seam of Zhaozhuang coalmine. The results show that (1) the top part of the coal seam is fractured coal, and the bottom is fragmented-mylonitic coal with a firmness coefficient value of less than 1.0. (2) In the hydraulic fracturing test of the layered rock-coal specimens in laboratory, the through-type vertical fractures are usually formed if the applied vertical stress is the maximum principal stress and is greater than 4 MPa compared with the maximum horizontal stress. However, horizontal fractures always developed when horizontal stress is the maximum or it is less than 4 MPa compared with vertical stress. (3) The in situ HWR-HFC hydraulic fracturing tests show that the detected maximum daily gas production is 11,000 m3, and the average gas production is about 7000 m3 per day. This implies that the CBM extraction using this method is increased by 50%~100% compared with traditional hydraulic fracturing in BSLP coal seams. The research result could give an indication of CBM developing in the broken-soft and low-permeability coal seams.

CoalBed Methane Pad Wells Completion and Artificial Lift Optimizations: Case Study From Australia Surat Basin DS Gas Field

2021 ◽  
Author(s):  
Li Ming ◽  
Xia Zhaohui ◽  
Liu Lingli ◽  
Cui Zehong ◽  
Duan LiJiang ◽  
...  
Keyword(s):  
Coalbed Methane ◽  
Optimization Methods ◽  
Gas Production ◽  
Production Performance ◽  
Vertical Wells ◽  
Coal Seams ◽  
Gas Field ◽  
Well Completion ◽  
Artificial Lift ◽  
Coalbed Methane Production

Abstract The Coalbed Methane in Australia Surat Basin is main gas source for LNG project in east coast of Australia[1]. Traditionally, Coalbed Methane are drilled by vertical wells. But there are big intensively farmed land coverage in the Surat Basin, the multiple wells on single, larger pad from the surface, the bores slant away at around 70 degrees to intersect multiple, thin coal seams are applied to avoid the extra "footprint" and decrease the environment affect. Many pad wells production failure because of poor interburden isolation. Excessive solids production in pad wells resulted in new failures of holes in tubing due to accelerated erosion, which bring big challenges for the Coalbed methane production in deviated pad wells. The gas production in pad wells are analysised and the new pad wells optimization are proposed. First, the complete wire log (at least include GR and density log curves) need to acquire for correct thin coal seams correlation and locate the interburden sandstone position for future good sandstone isolation. Second the customized completion strategy and placement (swell packer) are applied in the pad wells and specialized tubing with enhanced erosion resistance to extend the run life. Thirdly ESP pumps and optimized tubing are installed in new deviated wells for good gas production. After the pad wells were put into production, the gas production was kept well for long time without pump problems. Swell able packer completion significantly eliminates sand problem by isolating in excess of or close to 80% of interburden sand. The above well completion and artificial lift optimization methods bring good production performance for the new pad wells and contribute much production for the producing gas field. The swellable packer completion also can be used in vertical wells and will be standard well completion methods for future gas development wells.

scholarly journals Effects of Particle Size on Diffusion Kinetics in Chinese Anthracites during CH4 Desorption

Processes ◽  
2020 ◽  
Vol 8 (5) ◽  
pp. 514
Author(s):  
Jie Zang ◽  
Kai Wang ◽  
Yanbin Yu
Keyword(s):  
Particle Size ◽  
Coalbed Methane ◽  
Gas Flow ◽  
Hard Coal ◽  
Diffusion Kinetics ◽  
Methane Recovery ◽  
Coal Matrix ◽  
Matrix Blocks ◽  
Reported Data ◽  
Coalbed Methane Production

Diffusion kinetics is widely acknowledged to dominate gas flow in coal matrix blocks. Knowledge of this topic is important for ongoing coalbed methane recovery and CO2-enhanced coalbed methane production. Because laboratory diffusivity measurements are normally conducted on powdered coals, it is unclear how representative the results are for coalbeds. Investigations into the effects of particle size on gas diffusivity can provide insights into the in situ diffusivity of the coal matrix. This paper presents measured CH4 desorption data in two Chinese anthracites (one brittle, one hard) having different particle sizes, to investigate the effects of particle size on diffusion kinetics. The experimental data were fitted by both the unipore (UP) and bidisperse (BD) models. The BD model agreed better with the measured data than the UP model, especially for the brittle coal. This indicated that the brittle coal was more abundant in macropores than the hard coal. Diffusivity in the hard coal decreased with increasing particle size but varied stochastically within a small value range in the brittle coal as the particle size increased. The diffusivity of the brittle coal, with its higher vitrinite content and lower inertinite content, was greater compared with the hard coal. This was inconsistent with reported data in which vitrinite had a smaller diffusivity than inertinite. This anomalous phenomenon may be caused by the generation of comparatively more macropores during grinding in the brittle coal. These results indicate that the effects of particle size on diffusivity may be coal-dependent, and further, the effects of particle size are influenced by other factors, including coal structure.

scholarly journals Numerical Simulation Research on Well Pattern Optimization in High–Dip Angle Coal Seams: A Case of Baiyanghe Block

2021 ◽  
Vol 9 ◽  
Author(s):  
Hongli Wang ◽  
Xiao Zhang ◽  
Suian Zhang ◽  
Hongxing Huang ◽  
Jun Wang
Keyword(s):  
Coal Seam ◽  
Coalbed Methane ◽  
Horizontal Well ◽  
Gas Production ◽  
Low Rank ◽  
Water Migration ◽  
Coal Seams ◽  
Well Pattern ◽  
Dip Angle ◽  
Desorption Model

The Baiyanghe block in Fukang, Xinjiang, China, is rich in coalbed methane (CBM) resources, and several pilot experimental wells have yielded high production. Due to the high dip angle (35–55°) of the coal seam in this area, the lack of understanding of the geological characteristics, the physical properties of coal, and gas–water migration law lead to immature development techniques and poor overall development benefits. We first conducted desorption and adsorption tests on low-rank coal of this area and found residual gas in the coal. We established a coalbed methane desorption model suitable for this area by modifying the isotherm adsorption model. Next, by analyzing the influence of the gas–water gravity differentiation in the high–dip angle coal seam and the shallow fired coalbed methane characteristics in this area, we discovered the leakage of CBM from the shallow exposed area of the coal seam. Given the particular physical property of coal and gas–water migration characteristics in this area, we optimized the well pattern: (i) the U-shaped along-dip horizontal well group in coal seams is the main production well for gas production with a spacing distance of 312 m; (ii) a multistage fracturing well drilled in the floor of coal is for water production; and (iii) vertical wells with a spacing distance of 156 m in the shallow area is to capture CBM leakage. Using numerical simulation and net present value (NPV) economics models, we optimized the well pattern details. Applying our CBM desorption model, the numerical simulator can improve the accuracy of the low-rank coalbed methane productivity forecast. The optimization results demonstrated the following: 1) the cumulative gas production of single U-shaped well increased by 89% with the optimal well spacing, 2) the cumulative gas production of the well group increased by 87.54% after adding the floor staged horizontal well, and 3) the amount of CBM leakage decrease by 67.59%.

CO2 Injection Performance in the Fruitland Coal Fairway, San Juan Basin: Results of a Field Pilot

SPE Journal ◽  
2011 ◽  
Vol 16 (04) ◽  
pp. 864-879 ◽  
Author(s):  
Anne Y. Oudinot ◽  
George J. Koperna ◽  
Zeno G. Philip ◽  
Ning Liu ◽  
Jason E. Heath ◽  
...  
Keyword(s):  
Coalbed Methane ◽  
The United States ◽  
Gas Production ◽  
Injection Well ◽  
Co2 Injection ◽  
Small Scale ◽  
Steady Increase ◽  
San Juan ◽  
Coal Seams ◽  
Production Wells

Summary The Pump Canyon CO2-enhanced coalbed methane (ECBM)/ sequestration demonstration in New Mexico has the primary objective of demonstrating the feasibility of CO2 sequestration in deep, unmineable coal seams through a small-scale geologic sequestration pilot. This project is not the first of its kind; several small- or large-scale pilots were already conducted previously in the United States [Allison Unit (Reeves et al. 2003) in the San Juan, Appalachian, and Warrior basins] as well as internationally [the Recopol (Reeves and Oudinot 2002) project in Poland, and the Yubari project in Japan, Canada, and Australia]. Additional pilots are currently under way. At the project site, a new CO2-injection well was drilled within an existing pattern of coalbed-methane-production wells. Primarily operated by ConocoPhillips, these wells produce from the Late Cretaceous Fruitland coals. CO2 injection into these coal seams was initiated in late July 2008 and ceased in August 2009. A variety of monitoring, verification, and accounting (MVA) methods were employed to track the movement of the CO2 in order to determine the occurrence of leakage. Within the injection well, MVA methods included continuous measurement of injection volumes, pressures, and temperatures. The offset production wells sampled gas-production rates, pressures, and gas composition through CO2 sensors, tracers in the injected CO2, time-lapse vertical seismic profiling, and surface tiltmeter arrays. A detailed study of the overlying Kirtland shale was also conducted to investigate the integrity of this primary caprock. This information was used to develop a detailed geologic characterization and reservoir model that has been used to further understand the behavior of this reservoir. The CO2-injection pilot has ended with no significant CO2 buildup occurring in the offset production wells. However, a small but steady increase in CO2 and N2 at two of the offset wells may have been an indication of imminent breakthrough. More recent gas samples are, however, showing a decrease in CO2 and N2 content at those wells. This paper describes the project, covering the regulatory process and injection-well construction, the different techniques used to monitor for CO2 leakage, and the results of the modeling work.

scholarly journals Productivity subarea of CBM field and its key controlling factors: A case study in the Hancheng pilot test area, southeastern Ordos Basin, China

2018 ◽  
Vol 37 (1) ◽  
pp. 102-124 ◽  
Author(s):  
Yanfei Liu ◽  
Dazhen Tang ◽  
Song Li ◽  
Hao Xu ◽  
Shu Tao ◽  
...  
Keyword(s):  
Coalbed Methane ◽  
Ordos Basin ◽  
Gas Production ◽  
Test Area ◽  
Gas Content ◽  
Pilot Test ◽  
Coal Seams ◽  
Geological Factors ◽  
Drop Rate

The Hancheng block in the southeastern Ordos Basin is one of the earliest and the most important areas for coalbed methane exploration and development in China. However, there are significant production variations in different wells or even some adjacent wells in the Hancheng block. To reveal the reasons of production differences in such a small scale, further detailed studies of coalbed methane productivity in the Hancheng pilot test area, a precursor trial area in Hancheng block with mature, well-characterized coalbed methane reservoirs and long-term production database, were conducted. The influence of nine factors (including engineering and geological factors) on gas production was analyzed. By introducing the rough set theory, which is applicable to the vague, imprecise, and incomplete information system, this paper presents a method for quantitative evaluation of the influencing factors on gas production. The results indicate that there are certain distribution characteristics of productivity in Hancheng pilot test area, which can be partitioned into four zones. The degressive order of the influencing degree of these nine factors is (i) the distance between the well and the fault, (ii) the structure curvature of the coal seams, (iii) the gas content, (iv) the critical reservoir ratio, (v) the volume of the fracturing liquids per meter, (vi) the volume of the fracturing sand per meter, (vii) the dynamic liquid level drop rate, (viii) the depth, and (ix) the thickness. Geological factors, especially the influence of fault, structural curvature of the coal seams and gas content, play a major role in controlling long-term gas production. Engineering factors (effect of fracturing and dynamic liquid level drop rate) have always been integral parts of coalbed methane development.

Method and Application of Reducing Pressure and Increasing Production in Nanometer Porous Coal Seam

2021 ◽  
Vol 7 (5) ◽  
pp. 4608-4620
Author(s):  
Jia Liu ◽  
Yinghong Liu ◽  
Ruyong Feng ◽  
Na Li
Keyword(s):  
Coalbed Methane ◽  
Simulation Method ◽  
Gas Production ◽  
Coal Seams ◽  
Bottom Hole ◽  
Stable Production ◽  
Production Wells ◽  
Bottom Hole Flowing Pressure ◽  
Coalbed Methane Production ◽  
Production Period

Objectives: In order to deeply analyze the feasibility of reducing pressure and increasing production of coalbed methane wells in nano-porous coal seams and clarify the principle of well selection. Methods: The sensitivity of bottom hole flowing pressure to coalbed methane production is analyzed by establishing productivity equation in stable production period of coalbed methane wells. Combined with the numerical simulation method, the drainage and production effect of L-1 well in the Block A is simulated after reducing the flowing pressure at the bottom of the well. Results: The results show that for CBM wells that have been put into production, the effect of increasing the production can be achieved by reducing the bottom hole flowing pressure, and when the bottom hole flowing pressure is large, reducing the bottom hole flowing pressure can obtain a larger increase in gas production. The cumulative gas production of Well L-1 can be increased by 110x104m3 compared with the previous measures, and the increase rate can reach 85%. Conclusion: Combining with the pressure-reducing and increasing production wells in the Block A, the applicable conditions for pressure-dropping and increasing production to increase the production of CBM wells are proposed, that is, continuous and stable drainage and production, and there is a certain height of liquid column between the moving liquid level and the coal roof before operation.

Sign in / Sign up

Export Citation Format

Share Document