Impact Response Measurement of Poly-Urethane Sheet Using an Optical Interferometer

2017 ◽  
Vol 29 (3) ◽  
pp. 613-618
Author(s):  
Sa-nga Songmuang ◽  
◽  
Akihiro Takita ◽  
Suphanchai Punthawanunt ◽  
Keyword(s):  
High Speed ◽  
Impact Force ◽  
Inertial Force ◽  
Spherical Body ◽  
The Body ◽  
Impact Response ◽  
Optical Center ◽  
Optical Interferometer ◽  
Cube Corner ◽  
The Impact

[abstFig src='/00290003/16.jpg' width='300' text='The changes impact force to the sheet' ] A method for measuring the impact response of a polyurethane sheet is proposed. In the method, the velocity, acceleration, force, and displacement of a spherical body dropping onto the polyurethane sheet is measured using an optical interferometer. Only the velocity is measured from the Doppler shift of the laser light reflected on the cube corner prism embedded inside the spherical body. The optical center of the cube corner prism is made to coincide with the center of gravity of the whole spherical body to minimize the effect of the attitude change of the body. The acceleration, displacement, and inertial force of the body are calculated from the velocity. The dropping body is also observed using a high-speed camera. The uncertainty in measuring the instantaneous value of the impact force with a sampling interval of approximately 0.1 ms is estimated to be 0.23 N, which corresponds to 0.14% of the maximum force of approximately 1.60×102N. In the experiment, 10 drop measurements are conducted and show good reproducibility of this method.

Impact Response Measurement of Contact Lenses

2015 ◽  
Vol 643 ◽  
pp. 173-177
Author(s):  
Kazuhide Watanabe ◽  
Naoki Miyashita ◽  
Du Hong Bin ◽  
Kyohei Irisa ◽  
Akihiro Takita ◽  
...  
Keyword(s):  
Mechanical Characteristics ◽  
Contact Lenses ◽  
Impact Force ◽  
Inertial Force ◽  
Small Mass ◽  
High Accuracy ◽  
Impact Response ◽  
Linear Motion ◽  
Response Measurement ◽  
The Impact

Impact response of contact lenses is measured using the Levitation Mass Method (LMM). In the LMM, a small mass collides with contact lenses and the impact force is measured with high accuracy as the inertial force of the moving part. A pneumatic linear bearing is used to achieve linear motion with sufficiently small friction acting on the moving part. Hysteresis loop and consumed energy as mechanical characteristics of contact lenses are also calculated.

Influence of Attached Masses on Impact Forces and Running Style in Heel-Toe Running

1987 ◽  
Vol 3 (3) ◽  
pp. 264-275 ◽  
Author(s):  
Alexander Bahlsen ◽  
Benno M. Nigg
Keyword(s):  
Body Mass ◽  
High Speed ◽  
Impact Force ◽  
Force Plate ◽  
The Body ◽  
Additional Mass ◽  
Impact Forces ◽  
Running Shoes ◽  
High Speed Film ◽  
Vertical Impact

Impact forces analysis in heel-toe running is often used to examine the reduction of impact forces for different running shoes and/or running techniques. Body mass is reported to be a dominant predictor of vertical impact force peaks. However, it is not evident whether this finding is only true for the real body mass or whether it is also true for additional masses attached to the body (e.g., running with additional weight or heavy shoes). The purpose of this study was to determine the effect of additional mass on vertical impact force peaks and running style. Nineteen subjects (9 males, 10 females) with a mean mass of 74.2 kg/56.2 kg (SD = 10.0 kg and 6.0 kg) volunteered to participate in this study. Additional masses were attached to the shoe (.05 and .1 kg), the tibia (.2, .4, .6 kg), and the hip (5.9 and 10.7 kg). Force plate measurements and high-speed film data were analyzed. In this study the vertical impact force peaks, Fzi, were not affected by additional masses, the vertical active force peaks, Fza, were only affected by additional masses greater than 6 kg, and the movement was only different in the knee angle at touchdown, ϵ0, for additional masses greater than .6 kg. The results of this study did not support findings reported earlier in the literature that body mass is a dominant predictor of external vertical impact force peaks.

An experimental and simulation study of the flow pattern characteristics of water jet impingements in boreholes

2021 ◽  
pp. 014459872110520
Author(s):  
Yabin Gao ◽  
Xin Xiang ◽  
Ziwen Li ◽  
Xiaoya Guo ◽  
Peizhuang Han
Keyword(s):  
High Speed ◽  
Impact Force ◽  
Jet Impingement ◽  
Flow Patterns ◽  
Water Jet ◽  
Solid Boundary ◽  
Force Model ◽  
Water Jets ◽  
Contact Surfaces ◽  
The Impact

Hydraulic slotting has become one of the most common technologies adopted to increase permeability in low permeability in coal field seams. There are many factors affecting the rock breaking effects of water jets, among which the impact force cannot be ignored. To study the influencing effects of contact surface shapes on jet flow patterns and impact force, this study carried out experiments involving water jet impingement planes and boreholes under different pressure conditions. The investigations included numerical simulations under solid boundary based on gas–liquid coupling models and indoor experiments under high-speed camera observations. The results indicated that when the water jets impinged on different contact surfaces, obvious reflection flow occurred, and the axial velocity had changed through three stages during the development process. Moreover, the shapes of the contact surfaces, along with the outlet pressure, were found to have impacts on the angles and velocities of the reflected flow. The relevant empirical formulas were summarized according to this study's simulation results. In addition, the flow patterns and shapes of the contact surfaces were observed to have influencing effects on the impact force. An impact force model was established in this study based on the empirical formula, and the model was verified using both the simulation and experimental results. It was confirmed that the proposed model could provide important references for the optimization of the technical parameters water jet systems, which could provide theoretical support for the further intelligent and efficient transformation of coal mine drilling water jet technology.

scholarly journals Experimental investigation of the impact response of novel steelbiocomposite hybrid materials

2018 ◽  
Vol 183 ◽  
pp. 02040
Author(s):  
KarthikRam Ramakrishnan ◽  
Mikko Hokka ◽  
Essi Sarlin ◽  
Mikko Kanerva ◽  
Reijo Kouhia ◽  
...  
Keyword(s):  
High Speed ◽  
Structural Integrity ◽  
Metal Layer ◽  
Rear Surface ◽  
Impact Resistance ◽  
Natural Fibre ◽  
Image Correlation ◽  
Impact Response ◽  
High Speed Camera ◽  
The Impact

Recent developments in the production of technical flax fabrics allow the use of sustainable natural fibres to replace synthetic fibres in the manufacture of structural composite parts. Natural fibre reinforced biocomposites have been proven to satisfy design and structural integrity requirements but impact strength has been identified as one of their limitations. In this paper, hybridisation of the biocomposite with a metal layer has been investigated as a potential method to improve the impact resistance of natural fibre composites. The impact response of biocomposites made of flax-epoxy is investigated experimentally using a high velocity particle impactor. A high-speed camera setup was used to observe the rear surface of the plates during impact. Digital Image Correlation (DIC) of the high speed camera images was used for full-field strain measurement and to study the initiation and propagation of damage during the impact. The different modes of damage in the hybrid laminate were identified by postimpact analysis of the section of the damaged composite plate using optical microscopy. The study shows the difference in impact response for different material combinations and configurations. The hybrid construction was shown to improve the impact resistance of the flax composite.

Vibration Analysis of Different Micro-Beams with Laser Ablation

2013 ◽  
Vol 462-463 ◽  
pp. 428-431
Author(s):  
Liang Cai Xiong ◽  
Quan Sheng Zhou ◽  
Peng Chen
Keyword(s):  
Laser Ablation ◽  
Dynamic Response ◽  
Vibration Analysis ◽  
Laser Excitation ◽  
Impact Force ◽  
Laser Doppler Vibrometer ◽  
Impact Response ◽  
Vibration Velocity ◽  
Laser Shock ◽  
The Impact

The dynamic response of different micro-beams after laser excitation experiments have been investigated in this paper. The impact force that induces the vibration of micro-beams is the interaction of focused pulse laser and tested beams. The impact response of micro-beams after being excited is measured by Laser Doppler Vibrometer. Different beams such as cantilever beam, L-shaped beam are employed in our experiments. Comparisons of the vibration velocity and its frequencies of different beams have also been performed. Experimental results show that the mechanical effects of laser shock do really exist and can be utilized.

scholarly journals Experimental study of the impact response of geocells as components of rockfall protection embankments

2009 ◽  
Vol 9 (2) ◽  
pp. 459-467 ◽  
Author(s):  
S. Lambert ◽  
P. Gotteland ◽  
F. Nicot
Keyword(s):  
Experimental Study ◽  
Numerical Model ◽  
Boundary Conditions ◽  
Composite Structures ◽  
Impact Force ◽  
Impact Response ◽  
Rigid Base ◽  
Transmitted Force ◽  
The Impact ◽  
Rockfall Protection

Abstract. Rockfall protection embankments are ground levees designed to stop falling boulders. This paper investigates the behaviour of geocells to be used as components of these structures. Geocells, or cellular confinement systems, are composite structures associating a manufactured envelope with a granular geomaterial. Single cubic geocells were subjected to the impact resulting from dropping a spherical boulder. The geocells were filled with fine or coarse materials and different boundary conditions were applied on the lateral faces. The response is analysed in terms of the impact force and the force transmitted by the geocell to its rigid base. The influence on the geocell response of both the fill material and the cell boundary conditions is analysed. The aim was to identify the conditions resulting in greatest reduction of the transmitted force and also to provide data for the validation of a specific numerical model.

DYNAMIC CHARACTERISTICS MEASUREMENTS OF A FORCE TRANSDUCER AGAINST SMALL AND SHORT-DURATION IMPACT FORCES

2014 ◽  
Vol 21 (1) ◽  
pp. 59-66 ◽  
Author(s):  
Mitra Djamal ◽  
Kazuhide Watanabe ◽  
Kyohei Irisa ◽  
Irfa Aji Prayogi ◽  
Akihiro Takita ◽  
...  
Keyword(s):  
Short Duration ◽  
Dynamic Characteristics ◽  
Impact Force ◽  
Inertial Force ◽  
Small Mass ◽  
Force Transducer ◽  
Force Transducers ◽  
Impact Forces ◽  
Maximum Impact Force ◽  
The Impact

Abstract A method for evaluating the dynamic characteristics of force transducers against small and short-duration impact forces is developed. In this method, a small mass collides with a force transducer and the impact force is measured with high accuracy as the inertial force of the mass. A pneumatic linear bearing is used to achieve linear motion with sufficiently small friction acting on the mass, which is the moving part of the bearing. Small and short-duration impact forces with a maximum impact force of approximately 5 N and minimum half-value width of approximately 1 ms are applied to a force transducer and the impulse responses are evaluated.

scholarly journals Oblique impact of a smooth body on a thin layer of inviscid liquid

2013 ◽  
Vol 469 (2151) ◽  
pp. 20120615 ◽  
Author(s):  
T. I. Khabakhpasheva ◽  
A. A. Korobkin
Keyword(s):  
Body Surface ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Hydrodynamic Pressure ◽  
Oblique Impact ◽  
The Body ◽  
Second Stage ◽  
Smooth Body ◽  
Vertical Displacements ◽  
The Impact

The two-dimensional motion of a rigid body with a smooth surface is studied during its oblique impact on a liquid layer. The problem is coupled: the three degrees of freedom of the moving body are determined together with the liquid flow and the hydrodynamic pressure along the wetted part of the body surface. The impact process is divided into two temporal stages. During the first stage, the wetted region expands at a high speed with jetting flows at both ends of the wetted region. In the second stage, the free surface of the liquid is allowed to separate from the body surface. The position of the separation point is determined with the help of the Brillouin–Villat condition. Calculations are performed for elliptic cylinders of different masses and with different orientations and speeds before the impact. The horizontal and vertical displacements of the body, as well as its angle of rotation and corresponding speeds are investigated. The model developed remains valid until the body either touches the bottom of the liquid or rebounds from the liquid.

The Efficacy of Impact-Absorbing Materials during Collision with a Soccer Ball

2013 ◽  
Vol 440 ◽  
pp. 363-368
Author(s):  
Zahari Taha ◽  
Mohd Hasnun Arif Hassan ◽  
Mohd Azri Aris
Keyword(s):  
High Speed ◽  
Impact Force ◽  
Coefficient Of Restitution ◽  
Soccer Ball ◽  
Absorbing Materials ◽  
The Subject ◽  
The Impact ◽  
The Brain ◽  
Peak Impact Force ◽  
Impact Duration

The uniqueness of soccer is that the players are allowed to use their head to pass the ball to a teammate of even try to score goal. Studies have shown that heading in soccer might be dangerous to the brain and could lead to brain trauma. There are headgears available for soccer players to protect their head, but studies have proven that currently available headgears are ineffective in reducing the impact caused by a soccer ball. The objective of this study is to test the efficacy of six different types of impact-absorbing materials in reducing the linear impact force from a soccer ball. The soccer ball was dropped from the height of 2.3 m onto a force platform to measure the impact force. A high-speed camera is used to record the motion and the impact duration, and then the coefficient of restitution for each impact was determined. Polyurethane (PU) comb-gel was found to be the most effective material in reducing the peak impact force and impulse compared with other materials. The reduction in peak force was associated with longer impact duration between the soccer ball and the PU comb-gel. However, the coefficient of restitution was reduced by 21.7%, implying that using the gel alone will reduce the speed of the ball after heading, thus reducing the performance of a player wearing it. A combination of PU gel and another stiffer material is suggested and the effectiveness of the composite will be the subject of future investigation.

Sign in / Sign up

Export Citation Format

Share Document