New Design Methodology for RCC Using Elastomer Shear Pads

1997 ◽  
Vol 9 (5) ◽  
pp. 362-372 ◽  
Author(s):  
Sangwan Joo ◽  
◽  
Naotaka Yoshihara ◽  
Yasuhiro Masutani ◽  
Atsushi Nishikawa ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Design Methodology ◽  
Experimental Results ◽  
Complete Analysis ◽  
Lateral Stiffness ◽  
Variable Type ◽  
Wide Range ◽  
Fixed Type ◽  
Metal Layers

The mechanical behavior of RCC (Remote-Center-Compliance) devices using elastomer shear pads depends on the number of their elastomer-metal layers, the thickness and radius of the elastomer-metal, and the axial and lateral stiffness of the elastomer. These parameters must be considered in a complete analysis of the design of RCC devices. This paper presents a useful method for analyzing the behavior of RCC devices using elastomer shear pads based on the material mechanics approach. This makes it easy to design new RCCs for specific purposes. Moreover, we have developed a projection/stiffness variable type RCC (VRCC), and verified that a single VRCC duplicates the performance of a wide range of commercially available fixed-type RCCs. Simulation and experimental results are also presented.

The Measurement and Analysis of Ball Motion in High Speed Deep Groove Ball Bearings

1975 ◽  
Vol 97 (3) ◽  
pp. 341-348 ◽  
Author(s):  
R. J. Boness ◽  
J. J. Chapman
Keyword(s):  
High Speed ◽  
Experimental Results ◽  
Complete Analysis ◽  
Ball Speed ◽  
Rolling Axis ◽  
High Speeds ◽  
Deep Groove ◽  
Wide Range ◽  
Ring Mode ◽  
Ball Motion

This paper reports on a study of ball motion, including the measurement of ball rolling axis, in deep groove bearings operating at high speeds under thrust load conditions. The technique employed relies on viewing the test bearing, operating in the conventional fixed outer ring mode, through a rotating prism which eliminates optically the gross rotation of the separator. Videotape recordings of a selected ball, distinctively marked and illuminated stroboscopically, allows a complete analysis of ball bearing kinematics. Experimental results of separator speed, ball speed and rolling axis together with separator slip, ball slip and spin velocities at both the inner and outer raceway contacts are presented for a wide range of loads and shaft speeds up to 12,000 rev/min. These results are compared with the existing theory of Jones. Discrepancies between predicted and actual ball motion are due to the assumption made by Jones in neglecting bearing element slip. A further analysis of the experimental results including both gyroscopic torques and slip based on elastohydrodynamic traction values for the test lubricant explains actual ball motion more fully.

Application of TEM to Deformation, Wear, and Fracture of Ceramics

1974 ◽  
Vol 32 ◽  
pp. 472-473
Author(s):  
B. J. Hockey
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Mechanical Behavior ◽  
Brittle Materials ◽  
High Temperature Strength ◽  
Wide Range ◽  
Corrosive Environments ◽  
Further Development

Ceramics, such as Al2O3 and SiC have numerous current and potential uses in applications where high temperature strength, hardness, and wear resistance are required often in corrosive environments. These materials are, however, highly anisotropic and brittle, so that their mechanical behavior is often unpredictable. The further development of these materials will require a better understanding of the basic mechanisms controlling deformation, wear, and fracture.The purpose of this talk is to describe applications of TEM to the study of the deformation, wear, and fracture of Al2O3. Similar studies are currently being conducted on SiC and the techniques involved should be applicable to a wide range of hard, brittle materials.

On the nominal transverse shear strain to characterize the severity of creasing

TAPPI Journal ◽  
2018 ◽  
Vol 17 (04) ◽  
pp. 231-240
Author(s):  
Douglas Coffin ◽  
Joel Panek
Keyword(s):  
Shear Strain ◽  
Transverse Shear ◽  
Elastic Limit ◽  
Experimental Results ◽  
Transverse Shear Strain ◽  
Maximum Strain ◽  
Machine Direction ◽  
Engineering Approach ◽  
Wide Range ◽  
Analytic Expression

A transverse shear strain was utilized to characterize the severity of creasing for a wide range of tooling configurations. An analytic expression of transverse shear strain, which accounts for tooling geometry, correlated well with relative crease strength and springback as determined from 90° fold tests. The experimental results show a minimum strain (elastic limit) that needs to be exceeded for the relative crease strength to be reduced. The theory predicts a maximum achievable transverse shear strain, which is further limited if the tooling clearance is negative. The elastic limit and maximum strain thus describe the range of interest for effective creasing. In this range, cross direction (CD)-creased samples were more sensitive to creasing than machine direction (MD)-creased samples, but the differences were reduced as the shear strain approached the maximum. The presented development provides the foundation for a quantitative engineering approach to creasing and folding operations.

Development of a rational design methodology for precast concrete slender spandrel beams: Part 1, experimental results

PCI Journal ◽  
2011 ◽  
Vol 56 (2) ◽  
pp. 88-112 ◽  
Author(s):  
Gregory Lucier ◽  
Catrina Walter ◽  
Sami Rizkalla ◽  
Paul Zia ◽  
Gary Klein
Keyword(s):  
Design Methodology ◽  
Rational Design ◽  
Precast Concrete ◽  
Experimental Results

scholarly journals Numerical Phase-Field Model Validation for Dissolution of Minerals

2021 ◽  
Vol 11 (6) ◽  
pp. 2464
Author(s):  
Sha Yang ◽  
Neven Ukrainczyk ◽  
Antonio Caggiano ◽  
Eddie Koenders
Keyword(s):  
Phase Field ◽  
Liquid Interface ◽  
Mineral Dissolution ◽  
Experimental Results ◽  
Wide Range ◽  
Congruent Dissolution ◽  
Solid Liquid Interface ◽  
Solid Liquid ◽  
Dissolution Of Minerals ◽  
Meso Scale

Modelling of a mineral dissolution front propagation is of interest in a wide range of scientific and engineering fields. The dissolution of minerals often involves complex physico-chemical processes at the solid–liquid interface (at nano-scale), which at the micro-to-meso-scale can be simplified to the problem of continuously moving boundaries. In this work, we studied the diffusion-controlled congruent dissolution of minerals from a meso-scale phase transition perspective. The dynamic evolution of the solid–liquid interface, during the dissolution process, is numerically simulated by employing the Finite Element Method (FEM) and using the phase–field (PF) approach, the latter implemented in the open-source Multiphysics Object Oriented Simulation Environment (MOOSE). The parameterization of the PF numerical approach is discussed in detail and validated against the experimental results for a congruent dissolution case of NaCl (taken from literature) as well as on analytical models for simple geometries. In addition, the effect of the shape of a dissolving mineral particle was analysed, thus demonstrating that the PF approach is suitable for simulating the mesoscopic morphological evolution of arbitrary geometries. Finally, the comparison of the PF method with experimental results demonstrated the importance of the dissolution rate mechanisms, which can be controlled by the interface reaction rate or by the diffusive transport mechanism.

scholarly journals Is contact angle a cause or an effect? – A cautionary tale

2020 ◽  
Vol 146 ◽  
pp. 03004
Author(s):  
Douglas Ruth
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Angles ◽  
Two Dimensions ◽  
Experimental Results ◽  
Flow In Porous Media ◽  
Two Dimensional ◽  
Wide Range ◽  
Fluid Drop ◽  
Surrounding Fluid

The most influential parameter on the behavior of two-component flow in porous media is “wettability”. When wettability is being characterized, the most frequently used parameter is the “contact angle”. When a fluid-drop is placed on a solid surface, in the presence of a second, surrounding fluid, the fluid-fluid surface contacts the solid-surface at an angle that is typically measured through the fluid-drop. If this angle is less than 90°, the fluid in the drop is said to “wet” the surface. If this angle is greater than 90°, the surrounding fluid is said to “wet” the surface. This definition is universally accepted and appears to be scientifically justifiable, at least for a static situation where the solid surface is horizontal. Recently, this concept has been extended to characterize wettability in non-static situations using high-resolution, two-dimensional digital images of multi-component systems. Using simple thought experiments and published experimental results, many of them decades old, it will be demonstrated that contact angles are not primary parameters – their values depend on many other parameters. Using these arguments, it will be demonstrated that contact angles are not the cause of wettability behavior but the effect of wettability behavior and other parameters. The result of this is that the contact angle cannot be used as a primary indicator of wettability except in very restricted situations. Furthermore, it will be demonstrated that even for the simple case of a capillary interface in a vertical tube, attempting to use simply a two-dimensional image to determine the contact angle can result in a wide range of measured values. This observation is consistent with some published experimental results. It follows that contact angles measured in two-dimensions cannot be trusted to provide accurate values and these values should not be used to characterize the wettability of the system.

“Please tidy up before leaving”: nudging Airbnb guests toward altruistic behavior

2019 ◽  
Vol 13 (4) ◽  
pp. 524-530 ◽  
Author(s):  
Paul Ranson ◽  
Daniel Guttentag
Keyword(s):  
Social Presence ◽  
Design Methodology ◽  
Field Experiments ◽  
Experimental Results ◽  
Altruistic Behavior ◽  
Content Type ◽  
The Social ◽  
Relationship Model ◽  
Social Market ◽  
Practical Implications

Purpose This study aimed to investigate whether increasing the social presence within an Airbnb lodging environment could nudge guests toward altruistic cleaning behaviors. Design/methodology/approach The study was based around a theoretical framework combining the social-market versus money-market relationship model, nudge theory and social presence theory. A series of three field experiments were conducted, in which social presence was manipulated to test its impact on guest cleaning behaviors prior to departure. Findings The experimental results confirmed the underlying hypothesis that an Airbnb listing’s enhanced social presence can subtly induce guests to help clean their rental units prior to departure. Originality/value This study is the first to examine behavioral nudging in an Airbnb context. It is also one of the first field experiments involving Airbnb. The study findings offer clear theoretical and practical implications.

Numerical investigation of the propagation of shock waves in rigid porous materials: development of the computer code and comparison with experimental results

1996 ◽  
Vol 324 ◽  
pp. 163-179 ◽  
Author(s):  
A. Levy ◽  
G. Ben-Dor ◽  
S. Sorek
Keyword(s):  
Porous Materials ◽  
Initial Conditions ◽  
Computer Code ◽  
Experimental Results ◽  
Numerical Code ◽  
Materials Development ◽  
Numerical Predictions ◽  
Wide Range ◽  
Dimensional Version ◽  
The One

The governing equations of the flow field which is obtained when a thermoelastic rigid porous medium is struck head-one by a shock wave are developed using the multiphase approach. The one-dimensional version of these equations is solved numerically using a TVD-based numerical code. The numerical predictions are compared to experimental results and good to excellent agreements are obtained for different porous materials and a wide range of initial conditions.

Experimental Studies on Cooling Effectiveness of the Double-Decker Air Jet Impingement With Film Outflow

2007 ◽  
Author(s):  
Junkui Mao ◽  
Wen Guo ◽  
Zhenxiong Liu ◽  
Jun Zeng
Keyword(s):  
Infrared Radiation ◽  
Experimental Studies ◽  
Jet Impingement ◽  
Experimental Results ◽  
Thermal Camera ◽  
Local Cooling ◽  
Cooling Effectiveness ◽  
Air Jet ◽  
Double Decker ◽  
Wide Range

Experiments were carried out to investigate the cooling effectiveness of a lamellar double-decker impingement/effusion structure. Infrared radiation (I.R.) thermal camera was used to measure the temperature on the outside surface of the lamellar double-decker. Experimental results were obtained for a wide range of governing parameters (blowing rate M (0.0017∼0.0066), the ratio of the jet impingement distance to the diameter of film hole H/D (0.5∼1.25), the ratio of the distance between the jet hole and film hole to the diameter of the film hole P/D (0, 3, 4), and the material of double-decker (Steel and Copper)). It was observed that the local cooling effectiveness η varies with all these parameters in a complicated way. All the results show that higher cooling effectiveness η is achieved in larger blowing rate cases. A certain range of H/D and P/D can be designed to result in the maximum cooling effectiveness η. And η is less sensitive to the material type compared with those parameters such as H/D, M and P/D.

Constitutive modeling for the mechanical behavior of rubber with filler particles

2021 ◽  
Author(s):  
Sankalp Gour ◽  
Deepu Kumar Singh ◽  
Deepak Kumar ◽  
Vinod Yadav
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Mechanical Behavior ◽  
Experimental Observation ◽  
Continuum Mechanics ◽  
Constitutive Modeling ◽  
Carbon Nanoparticles ◽  
Material Behavior ◽  
Experimental Results ◽  
Filler Particles

Abstract The present study deals with the constitutive modeling for the mechanical behavior of rubber with filler particles. An analytical model is developed to predict the mechanical properties of rubber with added filler particles based on experimental observation. To develop the same, a continuum mechanics-based hyperelasticity theory is utilized. The model is validated with the experimental results of the chloroprene and nitrile butadiene rubbers filled with different volume fractions of carbon black and carbon nanoparticles, respectively. The findings of the model agree well with the experimental results. In general, the developed model will be helpful to the materialist community working in characterizing the material behavior of tires and other rubber-like materials.

Sign in / Sign up

Export Citation Format

Share Document