Slope Monitoring System at a Slope Behind an Important Cultural Asset

2011 ◽  
Vol 6 (1) ◽  
pp. 70-79 ◽  
Author(s):  
Kazunari Sako ◽  
◽  
Ryoichi Fukagawa ◽  
Tomoaki Satomi ◽  
◽  
...  
Keyword(s):  
Field Measurement ◽  
Slope Failure ◽  
Rainfall Intensity ◽  
Pore Water Pressure ◽  
Numerical Models ◽  
Water Pressure ◽  
Measurement Data ◽  
Warning System ◽  
Set Up ◽  
Relationship Of

Rainfall-induced slope failure has been responsible for great death and destruction in Japan. This is thus a primary consideration in preserving Japan’s many cultural important temples, palaces, and similar structures, especially in the ancient capital of Kyoto, where many important cultural assets are located on hillsides and near mountains. Our objective is to construct a slope-disaster warning system using real-time field measurement data, in-situ and laboratory testing, and numerical models. We set up field monitoring on a slope behind an important cultural asset in July 2004 to measure pore-water pressure, temperature, and rainfall intensity [1]. We firstly introduce our slope-disaster warning concept and field measurement results for the slope behind the important cultural asset in Kyoto. And then we discuss the relationship of rainfall intensity, seepage behavior, and slope failure based on monitoring data and model test results using a soil box apparatus.

The Analysis of Seepage Characteristics and Stability of Carbonaceous Mudstone Embankment Slope in Rainfall Condition

2012 ◽  
Vol 446-449 ◽  
pp. 1864-1868 ◽  
Author(s):  
Ling Zeng ◽  
Hong Yuan Fu ◽  
Tao Li ◽  
Yan Qi Qin
Keyword(s):  
Moisture Content ◽  
Pore Water ◽  
Slope Failure ◽  
Rainfall Intensity ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Intensity Change ◽  
Safety Coefficient ◽  
Embankment Slope ◽  
Volumetric Moisture Content

Based on the actual rainfall data and saturated-unsaturated seepage theory, the change of pore water pressure and volumetric moisture content of carbonaceous mudstone embankment slope were studied under designed rainfall intensity. At the same time, the effect of rainfall intensity change on the slope failure mode and safety coefficient was analyzed. The results of the study show that: Continuous rainfall will make the surface layer negative pore water pressure of carbonaceous mudstone embankment slope loss, and in transient saturation zone the volumetric moisture content reaches the saturated moisture content. Safety coefficient of carbonaceous mudstone embankment slope gradually decreases with the rainfall continuing, potential sliding surface also have the tendency of extending into the embankment.

scholarly journals Characteristics of landslides in unwelded pyroclastic flow deposits, southern Kyushu, Japan

2015 ◽  
Vol 3 (10) ◽  
pp. 6351-6378 ◽  
Author(s):  
M. Yamao ◽  
R. C. Sidle ◽  
T. Gomi ◽  
F. Imaizumi
Keyword(s):  
Pyroclastic Flow ◽  
Slope Failure ◽  
Rainfall Intensity ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Antecedent Rainfall ◽  
Rainfall Characteristics ◽  
Antecedent Conditions ◽  
Duration Threshold ◽  
Different Types

Abstract. We investigated 184 landslides that occurred in unwelded pyroclastic flow deposits (Shirasu) on southern Kyushu Island, Japan, that included detailed data on the rainfall characteristics and the timing of slope failure. Localized rainfall intensity, antecedent rainfall, and topography affected the hydrologic processes that triggered landslides. Antecedent rainfall (adjusted for evapotranspiration losses) for large (> 200 mm) storms that triggered landslides was much lower than for smaller (≤ 200 mm) storms. Mean storm intensity and antecedent 7 day rainfall (API7) thresholds of > 5 mm h-1 and ≤ 30 mm (or API30 ≤ 60 mm), respectively, were useful to identify landslides triggered by rapid pore water pressure response, especially for shorter (< 20 h) duration events. During smaller storms with lower intensity, landslides are likely affected by a combined increase in soil weight and loss of suction when API30 ≥ 150 mm; simulations indicated that these weight and suction changes due to rainfall accumulation decreased factor of safety in steep Shirasu slopes, but did not necessarily trigger the landslides. All but two of the 21 landslides that plotted below a general rainfall intensity-duration threshold for landslide initiation had API30 values > 235 mm, indicating that they were highly influenced by the combined effects of the accumulated weight of rainfall and loss of suction. Our findings show that both event rainfall characteristics and antecedent conditions affect the hydrogeomorphic processes that trigger different types of landslides in Shirasu. This knowledge and the thresholds we have identified are useful for predicting the occurrence of different types of landslides in Shirasu deposits and improving sediment disaster prevention practices, including real-time warning systems.

scholarly journals Characteristics of landslides in unwelded pyroclastic flow deposits, southern Kyushu, Japan

2016 ◽  
Vol 16 (2) ◽  
pp. 617-627 ◽  
Author(s):  
M. Yamao ◽  
R. C. Sidle ◽  
T. Gomi ◽  
F. Imaizumi
Keyword(s):  
Pyroclastic Flow ◽  
Slope Failure ◽  
Rainfall Intensity ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Rainfall Characteristics ◽  
Hydrologic Processes ◽  
Antecedent Precipitation ◽  
Duration Threshold ◽  
Different Types

Abstract. We investigated 184 landslides that occurred in unwelded pyroclastic flow deposits (Shirasu) on southern Kyushu Island, Japan, that included detailed data on the rainfall characteristics and the timing of slope failure. Localized rainfall intensity, antecedent precipitation index (API), and topography affected the hydrologic processes that triggered landslides. API (adjusted for evapotranspiration losses) for large ( >  200 mm) storms that triggered landslides was much lower than for smaller ( ≤  200 mm) storms. Mean storm intensity and 7-day API (API7) thresholds of  >  5 mmh−1 and  ≤  30 mm (or API30 ≤  60 mm), respectively, were useful to identify landslides triggered by rapid pore water pressure response, especially for shorter ( <  20 h) duration events. During smaller storms with lower intensity, landslides are likely affected by a combined increase in soil weight and loss of suction when API30 ≥  150 mm; simulations indicated that these weight and suction changes due to rainfall accumulation decreased the factor of safety in steep Shirasu slopes, but did not necessarily trigger the landslides. Most of the landslides that were plotted below a general rainfall intensity–duration threshold for landslide initiation occurred during smaller storms with API30 values  >  200 mm, indicating that they were highly influenced by the combined effects of the accumulated weight of rainfall and loss of suction. Our findings show that both event rainfall characteristics and API affect the hydrogeomorphic processes that trigger different types of landslides in Shirasu. This knowledge and the thresholds we have identified are useful for predicting the occurrence of different types of landslides in unwelded Shirasu deposits and improving sediment disaster prevention practices, including real-time warning systems.

scholarly journals The Hydromechanical Interplay in the Simplified Three-Dimensional Limit Equilibrium Analyses of Unsaturated Slope Stability

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 73
Author(s):  
Panagiotis Sitarenios ◽  
Francesca Casini
Keyword(s):  
Analytical Solution ◽  
Slope Stability ◽  
Slope Failure ◽  
Failure Modes ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Three Dimensional ◽  
Stability Limit ◽  
Smooth Transition

This paper presents a three-dimensional slope stability limit equilibrium solution for translational planar failure modes. The proposed solution uses Bishop’s average skeleton stress combined with the Mohr–Coulomb failure criterion to describe soil strength evolution under unsaturated conditions while its formulation ensures a natural and smooth transition from the unsaturated to the saturated regime and vice versa. The proposed analytical solution is evaluated by comparing its predictions with the results of the Ruedlingen slope failure experiment. The comparison suggests that, despite its relative simplicity, the analytical solution can capture the experimentally observed behaviour well and highlights the importance of considering lateral resistance together with a realistic interplay between mechanical parameters (cohesion) and hydraulic (pore water pressure) conditions.

Type of Slope Failure Identified from Pore Water Pressure and Moisture Content Measurements

2015 ◽  
Vol 744-746 ◽  
pp. 690-694
Author(s):  
Muhammad Rehan Hakro ◽  
Indra Sati Hamonangan Harahap
Keyword(s):  
Moisture Content ◽  
Pore Pressure ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Failure Process ◽  
Small Scale ◽  
Content Increase ◽  
Sudden Increase ◽  
Model Slope

Rainfall-induced landslides occur in many parts of the world and causing a lot of the damages. For effective prediction of rainfall-induced landslides the comprehensive understanding of the failure process is necessary. Under different soil and hydrological conditions experiments were conducted to investigate and clarify the mechanism of slope failure. The failure in model slope was induced by sprinkling the rainfall on slope composed of sandy soil in small flume. Series of tests were conducted in small scale flume to better understand the failure process in sandy slopes. The moisture content was measured with advanced Imko TDR (Time Domain Reflectrometry) moisture sensors in addition to measurements of pore pressure with piezometers. The moisture content increase rapidly to reach the maximum possible water content in case of higher intensity of rainfall, and higher intensity of the rainfall causes higher erosion as compared to smaller intensity of the rainfall. The controlling factor for rainfall-induced flowslides was density of the slope, rather than intensity of the rainfall and during the flowslide the sudden increase in pore pressure was observed. Higher pore pressure was observed at the toe of the slope as compared to upper part of the slope.

scholarly journals Numerical Analysis to Assess the Vertical Drainage Within Flexible Pavement.

2018 ◽  
Vol 7 (4.20) ◽  
pp. 95
Author(s):  
Aqeel Al-Adili ◽  
Rasha H. Abdul-Amir ◽  
Osamah Hassan Chfat
Keyword(s):  
Cross Section ◽  
Rainfall Intensity ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Flux ◽  
Flexible Pavement ◽  
Laboratory Model ◽  
Typical Structure ◽  
Rainy Period ◽  
Vertical Drainage

In this research the work methodology include the software program SEEP/W routine of the GEOSLOPE 2012; which was used to simulate and analyze the vertical drainage of the pavement cross section using steady-state and transient analysis. A laboratory model consisting of typical structure layers of flexible pavement was considered in this research with a 2% slope with the influence of three different rain intensities (30mm/min, 60mm/min and 90mm/min); in which each one has a duration differs from the other. The results indicated that the value of the pore-water pressure in the surface layer resulting from 90 mm/min rainfall intensity is 83.65% greater than the pressure generated by the 60mm/min intensity of rain and 91.076% greater than the pressure produced from 30mm/min intensity. The average of accumulation water produced by the 30mm/min rainfall intensity in the pavement structure is 44.73 % greater than the average of accumulation of water from the 60mm/min intensity and 77.85% higher than the 90mm/min intensity of rain. The water flux through the pavement cross section during the rainy period of 30 mm/min was 8.42% higher than the water flux of 60 mm/min and 49.82% of the water flux of 90 mm/min intensity of rain.  

scholarly journals Slope Stability Analysis of Unsaturated Soil Slopes Based on the Site-Specific Characteristics: A Case Study of Hwangryeong Mountain, Busan, Korea

2020 ◽  
Vol 12 (7) ◽  
pp. 2839
Author(s):  
Sinhang Kang ◽  
Seung-Rae Lee ◽  
Sung-Eun Cho
Keyword(s):  
Relative Permeability ◽  
Rainy Season ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Air Flow ◽  
Influential Factors ◽  
Rainfall Infiltration ◽  
Site Specific ◽  
Hourly Rainfall

Shallow slope failures occur almost every year during the rainy season. Continuous observation of the meteorological parameters and hydrological characteristics is required to more clearly understand the triggering mechanisms of shallow slope failure. In addition, influential factors, such as type of relative permeability models, air flow, and variation of hydraulic conductivity associated with stress–strain behavior of soil, have significant effects on the actual mechanism of rainfall infiltration. Real-time data including hourly rainfall and pore water pressure in response to rainfall was recorded by devices; then, the change in pore pressure from the devices was compared to the results from the infiltration analysis with applications of three relative permeability models, air flow, and the coupled hydro-mechanical analysis to examine an appropriate site-specific approach to a rainfall infiltration analysis. The infiltration and stability analyses based on the site-specific hydrologic characteristics were utilized to create maps of safety factors that depend on the cumulative rainfall. In regions vulnerable to landslides, rainfall forecast information and safety factor maps built by applying various rainfall scenarios can be useful in preparing countermeasures against disasters during the rainy season.

scholarly journals Implications of the principle of effective stress

2020 ◽  
Author(s):  
Gerd Gudehus
Keyword(s):  
Critical Phenomena ◽  
Pore Water ◽  
Effective Stress ◽  
Critical Points ◽  
Pore Water Pressure ◽  
Numerical Models ◽  
Water Pressure ◽  
Shear Bands ◽  
Triaxial Tests ◽  
Water Saturated

AbstractWhile Terzaghi justified his principle of effective stress for water-saturated soil empirically, it can be derived by means of the neutrality of the mineral with respect to changes of the pore water pressure $$p_w$$ p w . This principle works also with dilating shear bands arising beyond critical points of saturated grain fabrics, and with patterns of shear bands as relics of critical phenomena. The shear strength of over-consolidated clay is explained without effective cohesion, which results also from swelling up to decay, while rapid shearing of water-saturated clay can lead to a cavitation of pore water. The $$p_w$$ p w -neutrality is also confirmed by triaxial tests with sandstone samples, while Biot’s relation with a reduction factor for $$p_w$$ p w is contestable. An effective stress tensor is heuristically legitimate also for soil and rock with relics of critical phenomena, particularly for critical points with a Mohr–Coulomb condition. Therein, the $$p_w$$ p w -neutrality of the solid mineral determines the interaction of solid fabric and pore water, but numerical models are questionable due to fractal features.

scholarly journals Seepage Analysis on the Surface Layer of Multistage Filled Slope with Rainfall Infiltration

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Bingxiang Yuan ◽  
Zengrui Cai ◽  
Mengmeng Lu ◽  
Jianbing Lv ◽  
Zhilei Su ◽  
...  
Keyword(s):  
Rainfall Intensity ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Rainfall Infiltration ◽  
Feature Points ◽  
Saturation State ◽  
Seepage Analysis ◽  
Safety Coefficient ◽  
Infiltration Model ◽  
Saturation Region

Based on the theory of rainfall infiltration, the surface infiltration model of multilevel filled slope was established by using the SEEP/W module of GeoStudio. The changes of the volumetric water content (VWC) and pore water pressure (PWP) in the surface of the slope during the rainfall infiltration were analyzed, and the influence of the change of the rainfall conditions on the VWC and PWP was considered. The analysis showed that VWC and PWP increased when the rain fell, and the growth rate of the higher feature point was higher. The affected area was concentrated on the upper part of the surface about 0.75 m. With the increasing of rainfall intensity, the slope surface getting to transient saturation state was quick, and the time of the PWP increasing to 0 among the feature points of same elevation was shortened. Meanwhile, the PWP presented a positive value, and as the infiltration depth increased, the transient saturation region expanded. The safety coefficient of the multistage filled slope was continuously reduced; after the stop of rainfall, the VWC and the PWP decreased, and the decline rate of the higher feature points was higher. In addition, the PWP of the lower part increased, and the safety factor of the slope presented a trend of rebound.

3D Numerical Analysis of Seismic Performances of Dyke on Liquefiable Soils

2011 ◽  
Vol 243-249 ◽  
pp. 3824-3831
Author(s):  
Ming Wu Wang ◽  
Guang Yi Chen
Keyword(s):  
Pore Water Pressure ◽  
Numerical Models ◽  
Water Pressure ◽  
Silica Sand ◽  
Three Dimension ◽  
Seismic Safety ◽  
Mechanism Model ◽  
Centrifuge Tests ◽  
Field Investigations ◽  
Effective Stress Analysis

Many field investigations of earthquake disaster cases confirm that earthquake-induced liquefaction is a main factor resulting in large damages to dyke. Consequently to ensure seismic safety of dyke on the liquefiable foundation, the research on seismic performances of dyke is of great importance. Herein seismic responses of dyke on the liquefiable soils were discussed by means of three dimension effective stress analysis method using a multiple shear mechanism model and liquefaction front. Two numerical models, in which the liquefiable foundation both consisted of saturated fine silica sand of 30% relative density and scenario waves with peak amplitude of 0.8056 and 3.133 m/s2 were used input waves, were conducted to investigate the distribution principles and the changing rules of deformation, acceleration, express pore water pressure, and shear dilatancy behavior in the dyke and the liquefiable foundation. The computed results do good agreements with the measured results from centrifuge tests. And these results may be of theoretical and realistic significance for seismic design of dyke on liquefiable soils.

Sign in / Sign up

Export Citation Format

Share Document