scholarly journals Effect of Cr-C Coatings on the Corrosion Resistance of 304 Stainless Steel in the Molten Sodium Polysulfide

2021 ◽  
pp. 21029
Author(s):  
Yanjie Ren ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
304 Stainless Steel ◽  
Molten Sodium ◽  
Sodium Polysulfide

OUTOKUMPU TYPE 630

Alloy Digest ◽  
2016 ◽  
Vol 65 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
High Performance ◽  
High Strength ◽  
Heat Treating ◽  
304 Stainless Steel ◽  
Type 304 ◽  
Type 304 Stainless Steel

Abstract Outokumpu Type 630 is a martensitic age hardenable alloy of composition 17Cr-4Ni. The alloy has high strength and corrosion resistance similar to that of Type 304 stainless steel. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-1238. Producer or source: Outokumpu High Performance Stainless.

Effect of RF plasma nitriding time on microhardness and corrosion resistance of 304 stainless steel

1992 ◽  
Vol 59 (3-4) ◽  
pp. 253-260 ◽  
Author(s):  
M.M. Ibrahim ◽  
F.M. El-Hossary ◽  
N.Z. Negm ◽  
M. Abed ◽  
R.E. Ricker
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Plasma Nitriding ◽  
304 Stainless Steel ◽  
Rf Plasma ◽  
Nitriding Time

The effects of morphology of ferrite and non-metallic inclusions on corrosion behaviour of as-cast 304 stainless steel

CORROSION ◽  
10.5006/3763 ◽  
2021 ◽  
Author(s):  
Danbin Jia ◽  
Liangcai Zhong ◽  
Jingkun Yu ◽  
Zhaoyang Liu ◽  
Yuting Zhou ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Corrosion Behaviour ◽  
Solidification Process ◽  
Inclusion Size ◽  
304 Stainless Steel ◽  
Experimental Conditions ◽  
Quenching Temperature ◽  
Δ Ferrite ◽  
Metallic Inclusions

The effects of morphology of ferrite and non-metallic inclusions on corrosion resistance of as-cast 304 stainless steel (304 SS) were investigated. With the decrease in quenching temperature from 1723 K to 1648 K, the different microstructures of the as-cast 304 SS were obtained as the following series: austenitic-lathy δ ferrite, austenitic-colony δ ferrite and austenitic-blocky δ ferrite, and the average inclusion size increased. The electrochemical results show that the sample with the microstructure of austenitic- lathy δ ferrite and smaller size inclusions had a higher corrosion tendency and the lower pitting resistance. Furthermore, the effect of morphology and content of ferrite on corrosion resistance was greater than that of inclusion size under the current experimental conditions. Therefore, a promising method was developed to improve the corrosion resistance of as-cast 304 SS by changing the solidification process.

scholarly journals Investigation of Microstructure and Corrosion Resistance of Dissimilar Welded Joint between 304 Stainless Steel and Pure Copper

2019 ◽  
Vol 1 (3) ◽  
pp. 76-82
Author(s):  
Sorush Niknamian
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Arc Welding ◽  
Pure Copper ◽  
Welding Process ◽  
Steel Part ◽  
304 Stainless Steel ◽  
Dissimilar Metals ◽  
304L Stainless Steel ◽  
Shielded Metal Arc Welding

Nowadays, welding of dissimilar metals has become significant. In this process, a number of parameters including but not limited to type of electrode, amount of current, preheating temperature, and welding rate, that are essential to be taken into account. For welding of dissimilar metals, various methods are exploited including shielded metal arc welding (SMAW) and gas tungsten arc welding (GTAW). The stimulus for studying welding of 304L stainless steel to pure copper originates from difficulties in joining copper parts of           water-circulating molds to their steel part. In this study, the welding is performed on plates of steel and copper using SMAW, GTAW and combined SMAW+GTAW welding methods with    EL-CuMn2, ENiCrMo-6 and ER70S-4 electrodes. In order to investigate the microstructure and corrosion resistance behavior of welds, the samples were characterized using microstructural study and polarization test. It was observed that among all four welding methods, only combined SMAW+GTAW welding process resulted in successful joint between 304L stainless steel and copper. Both obtained joints possess suitable microstructure and corrosion resistance.

scholarly journals Effects of NiSO4 Concentration on the Coloring Performance and Corrosion Resistance of the Colored Film on 304 Stainless Steel

Coatings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 598
Author(s):  
Wenwei Li ◽  
Jun-e Qu ◽  
Zhiyong Cao ◽  
Hairen Wang
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Electrochemical Impedance ◽  
Negative Impact ◽  
304 Stainless Steel ◽  
Nacl Solution ◽  
Time Curve ◽  
Steel Surfaces

The colored films were successfully prepared on the 304 stainless steel surfaces in coloring solutions with different NiSO4 contents. The purpose of this study was to investigate the effects of NiSO4 in the coloring solution on the coloring performance of 304 stainless steel and corrosion resistance of the obtained colored film in NaCl solution. The coloring rate was determined from coloring potential-time curve, and the protection properties of the color films in a 3.5% NaCl solution were characterized by potentiodynamic polarization scan, electrochemical impedance spectroscopy, and wear resistance test. The results showed that adding NiSO4 could accelerate the coloring process but brought about a negative impact on the surface’s corrosion resistance.

Effects of Laser Processing Parameters on Grain Boundary Character Distribution and Corrosion Resistance of Austenite Stainless Steel

2007 ◽  
Vol 561-565 ◽  
pp. 2473-2476 ◽  
Author(s):  
Sen Yang ◽  
Hiroyuki Kokawa ◽  
Zhan Jie Wang
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Laser Processing ◽  
Processing Parameters ◽  
Laser Surface ◽  
304 Stainless Steel ◽  
Grain Boundary Character Distribution ◽  
Grain Boundary Character ◽  
Laser Surface Remelting ◽  
Character Distribution

In order to modify grain boundary character distribution (GBCD) and to improve intergranualr corrosion (IGC) resistance of 304 stainless steel, laser surface remelting experiments were conducted on 304 stainless steel using a 2kW CW Nd: YAG laser, and the effects of laser processing parameters on GBCD and corrosion resistance were investigated in detail under the optimal annealing condition (1220K 28h). The experimental results showed that combination of laser surface remelting and the following annealing treatment could change the GBCD remarkably and improve the IGC resistance of 304 stainless steel. However, there are no obvious effects of laser processing parameters on the final depth of the processed zone, although the depth of the molten pool increases with the increase of the laser output power or the decrease of the scanning velocity, and the subsequent GBCD and corrosion resistance.

Sign in / Sign up

Export Citation Format

Share Document