scholarly journals Influence of Zirconium Content on Corrosion Resistance of Micro-Alloyed Steel Reinforced Concrete in Chloride Solutions

2020 ◽  
pp. 4702-4711
Author(s):  
Shi Shao Hua ◽  
Keyword(s):  
Corrosion Resistance ◽  
Reinforced Concrete ◽  
Alloyed Steel ◽  
Zirconium Content ◽  
Chloride Solutions ◽  
Steel Reinforced Concrete ◽  
Micro Alloyed Steel

Effect of Heat Treatment in Pipe Processing Stage on Corrosion Resistance of Micro-Alloyed Steel Hot-Rolled Products

Metallurgist ◽  
2020 ◽  
Vol 64 (3-4) ◽  
pp. 322-333
Author(s):  
I. G. Rodionova ◽  
A. V. Amezhnov ◽  
D. V. Kudashov ◽  
V. V. Naumenko ◽  
D. L. D’yakonov ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Alloyed Steel ◽  
Processing Stage ◽  
Micro Alloyed Steel ◽  
Pipe Processing ◽  
Hot Rolled

Modification of MnS inclusion by tellurium in 38MnVS6 micro-alloyed steel

2020 ◽  
Vol 117 (6) ◽  
pp. 615
Author(s):  
Ping Shen ◽  
Lei Zhou ◽  
Qiankun Yang ◽  
Zhiqi Zeng ◽  
Kenan Ai ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Aspect Ratio ◽  
Strong Influence ◽  
Experimental Results ◽  
Alloyed Steel ◽  
Equivalent Diameter ◽  
Small Aspect Ratio ◽  
Steel Quality ◽  
Eds Analysis ◽  
Micro Alloyed Steel

In 38MnVS6 steel, the morphology of sulfide inclusion has a strong influence on the fatigue life and machinability of the steel. In most cases, the MnS inclusions show strip morphology after rolling, which significantly affects the steel quality. Usually, the MnS inclusion with a spherical morphology is the best morphology for the steel quality. In the present work, tellurium was applied to 38MnVS6 micro-alloyed steel to control the MnS inclusion. Trace tellurium was added into 38MnVS6 steel and the effect of Te on the morphology, composition, size and distribution of MnS inclusions were investigated. Experimental results show that with the increase of Te content, the equivalent diameter and the aspect ratio of inclusion decrease strikingly, and the number of inclusions with small aspect ratio increases. The inclusions are dissociated and spherized. The SEM-EDS analysis indicates that the trace Te mainly dissolves in MnS inclusion. Once the MnS is saturated with Te, MnTe starts to generate and wraps MnS. The critical Te/S value for the formation of MnTe in the 38MnV6 steel is determined to be approximately 0.075. With the increase of Te/S ratio, the aspect ratio of MnS inclusion decreases and gradually reaches a constant level. The Te/S value in the 38MnVS6 steel corresponding to the change of aspect ratio from decreasing to constant ranges from 0.096 to 0.255. This is most likely to be caused by the saturation of Te in the MnS inclusion. After adding Te in the steel, rod-like MnS inclusion is modified to small inclusion and the smaller the MnS inclusion, the lower the aspect ratio.

The mathematical modelling of corrosion in hot dip galvanized steel reinforced concrete

2011 ◽  
Vol 2 (1) ◽  
pp. 1-12
Author(s):  
A. Hegyi ◽  
H. Vermeşan ◽  
V. Rus
Keyword(s):  
Mathematical Model ◽  
Reinforced Concrete ◽  
Numerical Model ◽  
Equation System ◽  
Galvanized Steel ◽  
Steel Reinforced Concrete ◽  
Numeric Model ◽  
Physical And Mathematical Models ◽  
Physical Phenomena ◽  
The Mathematical Model

Abstract In this paper we wish to present the numerical model elaborated in order to simulate some physical phenomena that influence the general deterioration of steel, whether hot dip galvanized or not, in reinforced concrete. We describe the physical and mathematical models, establishing the corresponding equation system, the initial and boundary conditions. We have also presented the numeric model associated to the mathematical model and the numeric methods of discretization and solution of the differential equations system that describes the mathematical model.

Sign in / Sign up

Export Citation Format

Share Document