scholarly journals Dynamics of the Chaplygin Ball with Variable Parameters

2020 ◽  
Vol 16 (3) ◽  
pp. 453-462
Author(s):  
A.V. Borisov ◽  
◽  
E.A. Mikishanina ◽  
Keyword(s):  
Variable Parameters ◽  
Chaplygin Ball

Model reactions for the study of hydrogenation and acidic activity of palladium catalysts

1987 ◽  
Vol 52 (8) ◽  
pp. 2019-2027 ◽  
Author(s):  
Libor Červený ◽  
Nguyen Thi Du ◽  
Ivo Paseka
Keyword(s):  
Palladium Catalysts ◽  
Styrene Oxide ◽  
Side Reactions ◽  
Pd Catalysts ◽  
Variable Parameters ◽  
Acid Properties ◽  
Liquid Phase Hydrogenation ◽  
Acid Catalysed Reactions ◽  
Different Content ◽  
Model Reactions

Palladium catalysts have been used to study the hydrogenation of 1-phenyl-2-butene-1-ol which is accompanied by several side reactions considered to be acid-catalysed. Another model reaction studied was dehydration and subsequent hydrogenation or hydrogenolysis of 1-phenyl-1,3-propanediol to 3-phenyl-1-propanol, accompanied by formation of propylbenzene. The dehydration and propylbenzene formation can be again classified as acid-catalysed reactions. Another one is methanolysis of styrene oxide taking place under conditions of liquid phase hydrogenation due to the acid properties of Pd-H systems. Hydrogenation activity of Pd catalysts was tested by hydrogenation of cyclohexene. Sixteen Pd catalysts on different supports and with different content of active component were used, their activity and selectivity was determined and the effect of variable parameters in the synthesis of these catalysts on the activity and selectivity is discussed.

Phase evolution of hydroxapatite coatings suspension plasma sprayed using variable parameters in simulated body fluid

2010 ◽  
Vol 204 (8) ◽  
pp. 1236-1246 ◽  
Author(s):  
Romain d'Haese ◽  
Lech Pawlowski ◽  
Muriel Bigan ◽  
Roman Jaworski ◽  
Marc Martel
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Phase Evolution ◽  
Variable Parameters ◽  
Plasma Sprayed

Free vibrations of orthotropic shells of revolution with variable parameters

1978 ◽  
Vol 14 (8) ◽  
pp. 820-825
Author(s):  
E. I. Bespalova ◽  
Ya. M. Grigorenko ◽  
A. B. Kitaigorodskii ◽  
A. I. Shinkar'
Keyword(s):  
Free Vibrations ◽  
Shells Of Revolution ◽  
Variable Parameters ◽  
Orthotropic Shells

scholarly journals Dynamic Quality of an Aerostatic Thrust Bearing with a Microgroove and Support Center on Elastic Suspension

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1492
Author(s):  
Vladimir Kodnyanko ◽  
Stanislav Shatokhin ◽  
Andrey Kurzakov ◽  
Lilia Strok ◽  
Yuri Pikalov ◽  
...  
Keyword(s):  
Dynamic Characteristics ◽  
Negative Impact ◽  
Aerostatic Bearing ◽  
Elastic Suspension ◽  
Variable Parameters ◽  
Aerostatic Bearings ◽  
Improved Design ◽  
Dynamic Quality ◽  
Bearing Layer

The disadvantage of aerostatic bearings is their low dynamic quality. The negative impact on the dynamic characteristics of the bearing is exerted by the volume of air contained in the bearing gap, pockets, and microgrooves located at the outlet of the feeding diaphragms. Reducing the volume of air in the flow path is a resource for increasing the dynamic quality of the aerostatic bearing. This article presents an improved design of an axial aerostatic bearing with simple diaphragms, an annular microgroove, and an elastic suspension of the movable center of the supporting disk. A mathematical model is presented and a methodology for calculating the static characteristics of a bearing and dynamic quality indicators is described. The calculations were carried out using dimensionless quantities, which made it possible to reduce the number of variable parameters. A new method for solving linearized and Laplace-transformed boundary value problems for transformants of air pressure dynamic functions in the bearing layer was applied, which made it possible to obtain a numerical solution of problems sufficient for practice accuracy. The optimization of the criteria for the dynamic quality of the bearing was carried out. It is shown that the use of an elastic suspension of the support center improves its dynamic characteristics by reducing the volume of compressed air in the bearing layer and choosing the optimal volume of the microgroove.

scholarly journals Using uniform design and regression methodology of turning parameters study of nickel alloy

2021 ◽  
Author(s):  
Shao-Hsien Chen ◽  
Chih-Hung Hsu
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Nickel Alloy ◽  
Design Methodology ◽  
Cutting Tool ◽  
Uniform Design ◽  
Machining Time ◽  
Variable Parameters ◽  
Cutting Test ◽  
Set Up

AbstractThe nickel alloy has good mechanical strength and corrosion resistance at high temperature; it is extensively used in aerospace and biomedical and energy industries, as well as alloy designs of different chemical compositions to achieve different mechanical properties. However, for high mechanical strength, low thermal conductivity, and surface hardening property, the nickel alloy has worse cutting tool life and machining efficiency than general materials. Therefore, how to select the optimum machining parameters will influence the workpiece quality, cost, and machining time. This research will be using a new experimental design methodology to the cutting parameter planning for nickel-based alloy cutting test, and used the uniform design methodology to cutting test to reduce the number of experiments. Three independent variable parameters are set up, including cutting speed, feed rate, and cutting depth, and four dependent variable parameters are set up, including cutting tool wear, surface roughness, machining time, and cutting force. A nickel alloy turning parameter model is built by using regression analysis to further predict the I/O relationship among various combinations of variables. The errors between actual values and prediction values are validated. When the cutting tool wear (VB) is 2.72~6.18%, the surface roughness (Ra) is 4.10~7.72%, the machining time (T) is 3.75~8.82%, and the cutting force (N) is 1.54~7.42%; the errors of various dependent variables are approximately less than 10%, so a high precision estimation model is obtained through a few experiments of uniform design method.

scholarly journals Wear and Friction Characteristics of 65Mn Steel for Spike-Tooth Harrow

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 319
Author(s):  
Zhiguo Lu ◽  
Chuanyu Du ◽  
Qingcai Chen ◽  
Tianying Niu ◽  
Na Wang ◽  
...  
Keyword(s):  
Friction And Wear ◽  
Working Environment ◽  
Manganese Steel ◽  
Wear Loss ◽  
Variable Parameters ◽  
Wear Characteristics ◽  
Before And After ◽  
Set Up ◽  
Worn Surface ◽  
Friction And Wear Characteristics

The friction and wear characteristics of spike-tooth material (65Mn steel) of Spike-Tooth Harrow in a two-stage peanut harvester were studied in this paper. The friction and wear tests of pin and disc on 65 manganese steel were carried out on the tribometer, then the wear loss and the friction coefficient were studied. The wear loss of the pin was acquired by calculating the mass of the pin before and after the experiment using an electronic balance. According to the actual working environment of peanut spring-finger, four variable parameters are set up: load, speed, soil moisture and soil type. The friction and wear characteristics of pins were studied under different loads, speeds and different soil environments. After wearing, the worn surface of the material was observed by scanning microscope and the wear mechanism was studied. The experimental results show that the wear of the pin increases with the increase of load and decreases with the increase of rotational speed in the same rotation number. Especially in the case of the sandy soil with 20% in moisture, a maximum wear loss of the pin is achieved.

scholarly journals Thermoelastic analysis of FGM hollow cylinder for variable parameters and temperature distributions using FEM

2020 ◽  
Vol 9 (1) ◽  
pp. 256-264
Author(s):  
Dinkar Sharma ◽  
Ramandeep Kaur
Keyword(s):  
Stress Field ◽  
Hollow Cylinder ◽  
Numerical Study ◽  
Axial Stress ◽  
Circumferential Stress ◽  
Functionally Graded ◽  
Gradient Index ◽  
Variable Parameters ◽  
Graded Material ◽  
Governing Differential Equation

AbstractThis paper presents, numerical study of stress field in functionally graded material (FGM) hollow cylinder by using finite element method (FEM). The FGM cylinder is subjected to internal pressure and uniform heat generation. Thermoelastic material properties of FGM cylinder are assumed to vary along radius of cylinder as an exponential function of radius. The governing differential equation is solved numerically by FEM for isotropic and anistropic hollow cylinder. Additionally, the effect of material gradient index (β) on normalized radial stresses, normalized circumferential stress and normalized axial stress are evaluated and shown graphically. The behaviour of stress versus normalized radius of cylinder is plotted for different values of Poisson’s ratio and temperature. The graphical results shown that stress field in FGM cylinder is influenced by some of above mentioned parameters.

scholarly journals Comparison of the Effects of Conching Parameters on the Contents of Three Dominant Flavan3-ols, Rheological Properties and Sensory Quality in Chocolate Milk Mass Based on Liquor from Unroasted Cocoa Beans

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2502
Author(s):  
Bogumiła Urbańska ◽  
Hanna Kowalska ◽  
Karolina Szulc ◽  
Małgorzata Ziarno ◽  
Irina Pochitskaya ◽  
...  
Keyword(s):  
Rheological Properties ◽  
Yield Stress ◽  
Sensory Quality ◽  
Raw Material ◽  
Antioxidant Compounds ◽  
Chocolate Milk ◽  
Cocoa Beans ◽  
Variable Parameters ◽  
The Relationship ◽  
Manufacturing Parameters

The content of polyphenols in chocolate depends on many factors related to the properties of raw material and manufacturing parameters. The trend toward developing chocolates made from unroasted cocoa beans encourages research in this area. In addition, modern customers attach great importance to how the food they consume benefits their bodies. One such benefit that consumers value is the preservation of natural antioxidant compounds in food products (e.g., polyphenols). Therefore, in our study we attempted to determine the relationship between variable parameters at the conching stage (i.e., temperature and time of) and the content of dominant polyphenols (i.e.,catechins, epicatechins, and procyanidin B2) in chocolate milk mass (CMM) obtained from unroasted cocoa beans. Increasing the conching temperature from 50 to 60 °C decreased the content of three basic flavan-3-ols. The highest number of these compounds was determined when the process was carried out at 50 °C. However, the time that caused the least degradation of these compounds differed. For catechin, it was 2 h; for epicatechin it was 1 h; and for procyanidin it was 3 h. The influence of both the temperature and conching time on the rheological properties of chocolate milk mass was demonstrated. At 50 °C, the viscosity and the yield stress of the conched mass showed its highest value.

Sign in / Sign up

Export Citation Format

Share Document