scholarly journals The estimation of emissions from internal combustion engines fuelled by bioethanol

2008 ◽  
Vol 132 (1) ◽  
pp. 39-43
Author(s):  
Zdzisław CHŁOPEK
Keyword(s):  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Ecological Effects ◽  
Combustion Engines ◽  
Spark Ignition Engines ◽  
Test Results ◽  
Toxic Emission ◽  
Bioethanol Fuel

The use of bioethanol fuels is one of the most efficient methods of reduction of toxic emission and reduction of engine noxiousness to the environment at the same time. The ecological effects of the bioethanol fuel application fuelling spark ignition engines and self–ignition engines are presented in the paper. The paper presents original, not yet published, test results of the Scania DC9 E02 270 engine.

scholarly journals The Importance of Thermal Barrier Coating in Compression and Spark Ignition Engines

2020 ◽  
Vol 9 (4) ◽  
pp. 1738-1742
Keyword(s):  
Thermal Barrier Coating ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Renewable Energy Sources ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Thermal Barrier ◽  
Combustion Engines ◽  
Spark Ignition Engines ◽  
Barrier Coating

This paper explains the importance of applying thermal barrier coating (TBC) technique in internal combustion engines by providing an effective way of reducing gas emission which are carbon monoxide (CO), oxide of nitrogen (NOX), hydrocarbon (HC) including particulate matter (PM) thereby increasing engine performance (brake thermal efficiency) achieved by applying coating layers on some internal combustion engine parts using materials with low thermal conductivities and matched coefficients of thermal expansion (CTE close to the substrate material) which are mainly ceramics. Energy demand for various activities of life is increasing on a daily basis. The world depends majorly on non-renewable energy sources from fossil fuels to meet these energy demands. To be comfortable in life, better means of transportation and provision of power are required. Compression and spark ignition engines which are also called Internal Combustion Engines (ICEs) provide better transport facilities and power. However, combusting these fuels in automobile and stationary engines produces unfriendly atmosphere, contaminates water and air that are consumed by man. Pollution created as a result of combustion of gases in ICE is one of the worst man made contribution to atmospheric pollution.

scholarly journals Analysis of thermodynamic parameters in spark ignition VCR engine

2019 ◽  
Vol 294 ◽  
pp. 05001
Author(s):  
Patryk Urbański ◽  
Maciej Bajerlein ◽  
Jerzy Merkisz ◽  
Andrzej Ziółkowski ◽  
Dawid Gallas
Keyword(s):  
Thermodynamic Parameters ◽  
Motion Analysis ◽  
Internal Combustion Engines ◽  
Initial Conditions ◽  
Combustion Process ◽  
Internal Combustion ◽  
3D Models ◽  
Spark Ignition ◽  
Combustion Engines ◽  
Combustion Processes

3D models of Szymkowiak and conventional engines were created in the Solidworks program. During the motion analysis, the characteristics of the piston path were analyzed for the two considered engine units. The imported file with the generated piston routes was used in the AVL Fire program, which simulated combustion processes in the two engines with identical initial conditions. The configurations for two different compression ratios were taken into account. The basic thermodynamic parameters occurring during the combustion process in internal combustion engines were analyzed.

Thermophysical Properties of Working Substance and Heat Transfer in a Hydrogen Combustion Engine

2003 ◽  
Author(s):  
T. Shudo ◽  
H. Oka
Keyword(s):  
Heat Transfer ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Thermophysical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Combustion Engines

Hydrogen is a clean alternative to fossil fuels for internal combustion engines and can be easily used in spark-ignition engines. However, the characteristics of the engines fueled with hydrogen are largely different from those with conventional hydrocarbon fuels. A higher burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a higher degree of constant volume and a larger heat transfer from the burning gas to the combustion chamber wall of the engines. Because of the large heat loss, the thermal efficiency of an engine fueled with hydrogen is sometimes lower than that with hydrocarbons. Therefore, the analysis and the reduction of the heat loss are crucial for the efficient utilization of hydrogen in internal combustion engines. The empirical correlations to describe the total heat transferred from the burning gas to the combustion chamber walls are often used to calculate the heat loss in internal combustion engines. However, the previous research by one of the authors has shown that the widely used heat transfer correlations cannot be properly applied to the hydrogen combustion even with adjusting the constants in them. For this background, this research analyzes the relationship between characteristics of thermophysical properties of working substance and heat transfer to the wall in a spark-ignition engine fueled with hydrogen.

Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

scholarly journals Ecological comparative assessment of selected materials used for the construction of spark ignition engines

2020 ◽  
Vol 183 (4) ◽  
pp. 11-14
Author(s):  
Małgorzata Mrozik
Keyword(s):  
Energy Consumption ◽  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Comparative Assessment ◽  
Combustion Engines ◽  
Spark Ignition Engines ◽  
So2 Emissions ◽  
Passenger Cars ◽  
Materials Used ◽  
Degree Of Recovery

The aim of the article is to present the environmental effects of changes in material composition in selected internal combustion engines used in passenger cars using LCA analysis. The levels of energy consumption and emissions of pollutants related to material inputs occurring at the stage of engine production have been determined. The simplified LCA model presented in the paper shows the energy consumption and total CO2 and SO2 emissions on the basis of the mass of materials from which the engine is made. The research results presented in the paper give a picture of a modern passenger car engine on the basis of wear and the degree of recovery of materials used for its construction.

DEVELOPMENT OF AN ELECTRONIC CONTROL SYSTEM FOR GAS-ENGINES WITH SPARK IGNITION, CONVERTED ON THE BASIS OF DIESEL ENGINES TO WORK FOR ON LIQUEFIED PETROLEUM GAS

2018 ◽  
pp. 12-18 ◽  
Author(s):  
Serhii Kovalov
Keyword(s):  
Control System ◽  
Diesel Engines ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Combustion Engines ◽  
Electronic Control ◽  
Liquefied Petroleum Gas ◽  
Electronic Control System

The expediency and advantages of using gas motor fuels, in particular, liquefied petroleum gas with respect to traditional liquid motor fuels, are shown. Technical solutions for the use of liquefied petroleum gas by diesel engines are presented and analysed. The expediency and advantages of converting diesel engines to gas spark ignition internal combustion engines with respect to conversion to gas diesel engines. Developed by the Ukrainian synthesis technology Avenir Gaz has for converting diesel engines to gas internal combustion engines with spark ignition. According to the synthesis technology of Avenir Gaz, re-equipment of diesel engines of vehicles is carried out on the basis of the universal electronic control system for gas internal combustion engines, which is based on the multifunctional electronic microprocessor control unit Avenir Gaz 37. The developed electronic microprocessor control system for gas internal combustion engines with forced ignition has a modular structure and consists of two main and a number of additional subsystems. A schematic diagram of a universal electronic control system of a gas internal combustion engine with spark ignition for operation on liquefied petroleum gas is presented. The principle of operation of the main subsystems, which include the subsystem of power management and injection of liquefied petroleum gas by gas electromagnetic injectors into the intake manifold of a gas engine, and the principle of operation of the control subsystem of the ignition with two-spark ignition coils are described. A multifunctional electronic control unit Avenir Gaz 37 has been designed and manufactured. Non-motorized tests of the electronic control unit confirmed its performance. Based on the synthesis technology of Avenir Gaz using the universal electronic control system for gas internal combustion engines with the Avenir Gaz 37 ECU, the D-240 diesel engine was converted into a gas spark ignition internal combustion engine of the D-240-LPG model. Keywords: gas internal combustion engine with forced ignition, liquefied petroleum gas (LPG), electronic microprocessor control system for gas internal combustion engines, vehicles operating on LPG.

Sign in / Sign up

Export Citation Format

Share Document