scholarly journals An investigation of supercharged CAI engine with internal gas recirculation and direct gasoline injection

2012 ◽  
Vol 150 (3) ◽  
pp. 63-71
Author(s):  
Jacek HUNICZ ◽  
Michał GĘCA
Keyword(s):  
Direct Injection ◽  
Substantial Reduction ◽  
Combustion Process ◽  
Gasoline Direct Injection ◽  
Exhaust Emission ◽  
Boost Pressure ◽  
Auto Ignition ◽  
Intake Pressure ◽  
Negative Valve Overlap ◽  
Gas Recirculation

Influence of boost pressure on combustion process and exhaust emission in controlled auto-ignition (CAI) engine was studied. The examinations were carried out using single-cylinder engine with fully variable valvetrain and gasoline direct injection. In order to achieve auto-ignition in-cylinder temperature was elevated with the use of internal gas recirculation (EGR) obtained via the negative valve overlap (NVO) technique. Fuel dilution obtained via increase of intake pressure resulted in substantial reduction of cylinder-out nitrogen oxides emission. However application of boosting resulted in excessive advance of auto-ignition timing and increase of pressure rate rise (PRR) at higher engine loads.

scholarly journals Numerical Simulation of Knock Combustion in a Downsizing Turbocharged Gasoline Direct Injection Engine

2019 ◽  
Vol 9 (19) ◽  
pp. 4133 ◽  
Author(s):  
Wang ◽  
Zhang ◽  
Wang ◽  
Han ◽  
Chen
Keyword(s):  
Direct Injection ◽  
Combustion Process ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Valve Lift ◽  
Fuel Droplets ◽  
Gasoline Direct Injection Engine ◽  
Auto Ignition ◽  
Combustion Simulation

Engine knock has become the prime barrier to significantly improve power density and efficiency of the engines. To further look into the essence of the abnormal combustion, this work studies the working processes of normal combustion and knock combustion under practical engine operating conditions using a three-dimensional computation fluid dynamics (CFD) fluid software CONVERGE (Version 2.3.0, Convergent Science, Inc., Madison, USA). The results show that the tumble in the cylinder is gradually formed with the increase of the valve lift, enhances in the compression stroke and finally is broken due to the extrusion of the piston. The fuel droplets gradually evaporate and move to the intake side under the turbulent and high temperature in the cylinder. During the normal combustion process, the flame propagates faster on the intake side and it facilitates mixture in cylinder combustion. During the knock combustion simulation, the hotspots near the exhaust valve are observed, and the propagating detonation wave caused by multiple hotspots auto-ignition indicates significant effects on knock intensity of in-cylinder pressure.

Experimental and numerical analyses of the combustion process in a direct injection gasoline engine

2000 ◽  
Vol 1 (2) ◽  
pp. 147-161 ◽  
Author(s):  
J Reissing ◽  
H Peters ◽  
J. M. Kech ◽  
U Spicher
Keyword(s):  
Numerical Investigation ◽  
Gasoline Engine ◽  
Numerical Models ◽  
Direct Injection ◽  
Combustion Process ◽  
Experimental Methods ◽  
Spark Ignition Engine ◽  
Gasoline Direct Injection ◽  
Direct Injection Gasoline Engine ◽  
Gdi Engines

Gasoline direct injection (GDI) spark ignition engine technology is advancing at a rapid rate. The development and optimization of GDI engines requires new experimental methods and numerical models to analyse the in-cylinder processes. Therefore the objective of this paper is to present numerical and experimental methods to analyse the combustion process in GDI engines. The numerical investigation of a four-stroke three-valve GDI engine was performed with the code KIVA-3V [1]. For the calculation of the turbulent combustion a model for partially premixed combustion, developed and implemented by Kech [4], was used. The results of the numerical investigation are compared to experimental results, obtained using an optical fibre technique in combination with spectroscopic temperature measurements under different engine conditions. This comparison shows good agreement in temporal progression of pressure. Both the numerical simulation and the experimental investigation predicted comparable combustion phenomena.

Extending Lean and Exhaust Gas Recirculation-Dilute Operating Limits of a Modern Gasoline Direct-Injection Engine Using a Low-Energy Transient Plasma Ignition System

2016 ◽  
Vol 138 (11) ◽  
Author(s):  
James Sevik ◽  
Thomas Wallner ◽  
Michael Pamminger ◽  
Riccardo Scarcelli ◽  
Dan Singleton ◽  
...  
Keyword(s):  
Direct Injection ◽  
Exhaust Gas Recirculation ◽  
Low Energy ◽  
Gasoline Direct Injection ◽  
Combustion Stability ◽  
Exhaust Gas ◽  
Ignition System ◽  
Plasma Ignition ◽  
Gas Recirculation ◽  
Transient Plasma

The efficiency improvement and emissions reduction potential of lean and exhaust gas recirculation (EGR)-dilute operation of spark-ignition gasoline engines is well understood and documented. However, dilute operation is generally limited by deteriorating combustion stability with increasing inert gas levels. The combustion stability decreases due to reduced mixture flame speeds resulting in significantly increased combustion initiation periods and burn durations. A study was designed and executed to evaluate the potential to extend lean and EGR-dilute limits using a low-energy transient plasma ignition system. The low-energy transient plasma was generated by nanosecond pulses and its performance compared to a conventional transistorized coil ignition (TCI) system operated on an automotive, gasoline direct-injection (GDI) single-cylinder research engine. The experimental assessment was focused on steady-state experiments at the part load condition of 1500 rpm 5.6 bar indicated mean effective pressure (IMEP), where dilution tolerance is particularly critical to improving efficiency and emission performance. Experimental results suggest that the energy delivery process of the low-energy transient plasma ignition system significantly improves part load dilution tolerance by reducing the early flame development period. Statistical analysis of relevant combustion metrics was performed in order to further investigate the effects of the advanced ignition system on combustion stability. Results confirm that at select operating conditions EGR tolerance and lean limit could be improved by as much as 20% (from 22.7 to 27.1% EGR) and nearly 10% (from λ = 1.55 to 1.7) with the low-energy transient plasma ignition system.

scholarly journals Particulate emissions from a highly boosted gasoline direct injection engine

2017 ◽  
Vol 19 (3) ◽  
pp. 347-359 ◽  
Author(s):  
Felix Leach ◽  
Richard Stone ◽  
Dave Richardson ◽  
Andrew Lewis ◽  
Sam Akehurst ◽  
...  
Keyword(s):  
Particle Number ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Back Pressure ◽  
Gasoline Direct Injection ◽  
Exhaust Gas ◽  
Fuel Injection Pressure ◽  
Gas Recirculation ◽  
Operating Points

Downsized, highly boosted, gasoline direct injection engines are becoming the preferred gasoline engine technology to ensure that increasingly stringent fuel economy and emissions legislation are met. The Ultraboost project engine is a 2.0-L in-line four-cylinder prototype engine, designed to have the same performance as a 5.0-L V8 naturally aspirated engine but with reduced fuel consumption. It is important to examine particle number emissions from such extremely highly boosted engines to ensure that they are capable of meeting current and future emissions legislation. The effect of such high boosting on particle number emissions is reported in this article for a variety of operating points and engine operating parameters. The effect of engine load, air–fuel ratio, fuel injection pressure, fuel injection timing, ignition timing, inlet air temperature, exhaust gas recirculation level, and exhaust back pressure has been investigated. It is shown that particle number emissions increase with increase in cooled, external exhaust gas recirculation and engine load, and decrease with increase in fuel injection pressure and inlet air temperature. Particle number emissions are shown to fall with increased exhaust back pressure, a key parameter for highly boosted engines. The effects of these parameters on the particle size distributions from the engine have also been evaluated. Significant changes to the particle size spectrum emitted from the engine are seen depending on the engine operating point. Operating points with a bias towards very small particle sizes were noted.

Control of a spark ignition homogeneous charge compression ignition mode transition on a gasoline direct injection engine

2007 ◽  
Vol 221 (7) ◽  
pp. 867-875 ◽  
Author(s):  
G Tian ◽  
Z Wang ◽  
Q Ge ◽  
J Wang ◽  
S Shuai
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Direct Injection ◽  
Spark Ignition ◽  
Gasoline Direct Injection ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Key Issues ◽  
Cam Profile ◽  
Negative Valve Overlap ◽  
Homogeneous Charge

The hybrid combustion mode is an ideal operation strategy for a gasoline homogeneous charge compression ignition (HCCI) engine. A stable and smooth spark ignition (SI)/HCCI switch has been an issue in the research on multimode combustion. In this paper, the switch process has two key issues; the cam profile and throttle opening. With the developed two-stage cam system, the valve phase strategy can be switched within one engine cycle, from the normal cam profile for the SI mode to a negative valve overlap (NVO) profile for the HCCI mode, or vice versa. For a smoother and more stable switch, the throttle change was separated from the cam profile switch, which was called the stepped switch. The effect of throttle opening on HCCI combustion was studied, and the results showed that the concept of the stepped switch was reliable. With gasoline direct injection (GDI) the combustion mode switches from both SI and HCCI sides were smooth, rapid, and robust, without any abnormal combustion such as knocking and misfiring.

An Experimental Investigation on the Combustion Process of a Simulated Turbocharged Spark Ignition Natural Gas Engine Operated on Stoichiometric Mixture

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Hailin Li ◽  
Timothy Gatts ◽  
Shiyu Liu ◽  
Scott Wayne ◽  
Nigel Clark ◽  
...  
Keyword(s):  
Natural Gas ◽  
Flame Propagation ◽  
Combustion Process ◽  
Propagation Speed ◽  
Spark Ignition ◽  
Boost Pressure ◽  
Stoichiometric Mixture ◽  
Process Data ◽  
Intake Pressure ◽  
Flame Propagation Speed

This research investigated the combustion process of an AVL Model LEF/Volvo 5312 single cylinder engine configured to simulate the operation of a heavy-duty spark ignition (SI) natural gas (NG) engine operated on stoichiometric mixture. The factors affecting the combustion process that were examined include intake pressure, spark timing (ST), and the addition of diluents including nitrogen (N2) and carbon dioxide (CO2) to the NG to simulate low British thermal unit (BTU) gases. The mixing of diluents with NG is able to slow down the flame propagation speed, suppress the onset of knock, and allow the engine to operate on higher boost pressure for higher power output. The addition of CO2 was more effective than N2 in suppressing the onset of knock and slowing down the flame propagation speed due to its high heat capacity. Boosting intake pressure significantly increased the heat release rate (HRR) evaluated on J/°CA basis which represents the rate of mass of fuel burning. However, its impact on the normalized HRR evaluated on %/°CA basis, representing the flame propagation rate, was relatively mild. Boosting the intake pressure from 1.0 to 1.8 bar without adding diluents increased the peak HRR to 1.96 times of that observed at 1.0 bar. The increase was due to the burning of more fuel (about 1.8 times), and the 12.9% increase in the normalized HRR. The latter was due to the shortened combustion duration from 23.6 to 18.2 °CA, a 22.9% reduction. The presence of 40% CO2 or N2 in their mixture with NG increased the peak cylinder pressure (PCP) limited brake mean effective pressure (BMEP) from 17.2 to about 20.2 bar. The combustion process of a turbocharged SI NG engine can be approximated by referring to the HRR measured under a naturally aspirated condition. This makes it convenient for researchers to numerically simulate the combustion process and the onset of knock of turbocharged SI NG engines using combustion process data measured under naturally aspirated conditions as a reference.

scholarly journals New engine method for biodiesel cetane number testing

2008 ◽  
Vol 12 (1) ◽  
pp. 125-138 ◽  
Author(s):  
Radivoje Pesic ◽  
Aleksandar Davinic ◽  
Stevan Veinovic
Keyword(s):  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Process ◽  
Laboratory Equipment ◽  
Auto Ignition ◽  
Working Parameters ◽  
Biodiesel Fuels ◽  
Engine Method

Substitution of fossil fuels with fuels that come from part renewable sources has been a subject of many studies and researches in the past decade. Considering the higher cost and limits of production resources, a special attention is focused on raising the energy efficiency of biofuel usage, mainly through optimization of the combustion process. Consequently, in biofuel applications, there is a need for determination of auto-ignition quality expressed by cetane number as a dominant characteristic that influences combustion parameters. The fact that the method for cetane number determination is comparative in nature has led us to try to develop substitute engine method for cetane number determination, by the use of the available laboratory equipment and serial, mono-cylinder engine with direct injection, DMB LDA 450. Description of the method, results of optimization of engine?s working parameters for conduction of the test and method?s Accuracy estimation are given in the paper. The paper also presents the results of domestic biodiesel fuels cetane number testing with the application of described engine method, developed at the Laboratory for internal combustion engines and fuels and lubricants of the Faculty of Mechanical Engineering from Kragujevac, Serbia.

Simulation-Aided Development of Prechamber Ignition System for a Lean-Burn Gasoline Direct Injection Motor-Sport Engine

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Muhammed Fayaz Palakunnummal ◽  
Priyadarshi Sahu ◽  
Mark Ellis ◽  
Marouan Nazha
Keyword(s):  
Thermal Efficiency ◽  
Direct Injection ◽  
Fuel Mixture ◽  
Gasoline Direct Injection ◽  
Lean Burn ◽  
Ignition System ◽  
Motor Sport ◽  
Auto Ignition ◽  
Computational Fluid Dynamics Cfd ◽  
Sport Events

Abstract Due to recent regulation changes to restricted fuel usage in various motor-sport events, motor-sport engine manufacturers have started to focus on improving the thermal efficiency and often claim thermal efficiency figures well above equivalent road car engines. With limited fuel allowance, motor-sport engines are operated with a lean air–fuel mixture to benefit from higher cycle efficiency, requiring an ignition system that is suitable for the lean mixture. Prechamber ignition is identified as a promising method to improve lean limit and has the potential to reduce end gas auto-ignition. This paper analyses the full-load performance of a motor-sport lean-burn gasoline direct injection (GDI) engine and a passive prechamber is developed with the aid of a computational fluid dynamics (CFD) tool. The finalized prechamber design benefited in a significant reduction in burn duration, reduced cyclic variation, knock limit extension, and higher performance.

Development of Gasoline Direct Injection Engine for Improving Brake Thermal Efficiency Over 44%

2020 ◽  
Vol 142 (10) ◽  
Author(s):  
Dongwon Jung ◽  
Byeongseok Lee ◽  
Jinwook Son ◽  
Soohyung Woo ◽  
Youngnam Kim
Keyword(s):  
Thermal Efficiency ◽  
Direct Injection ◽  
Stability Limit ◽  
Spark Ignition ◽  
Gasoline Direct Injection ◽  
Brake Thermal Efficiency ◽  
Gasoline Direct Injection Engine ◽  
Combustion Duration ◽  
Test Engine ◽  
Gas Recirculation

Abstract This study demonstrates the effects of technologies applied for the development of gasoline direct injection (GDI) engine for improving the brake thermal efficiency (BTE). The test engine has a relatively high stroke to bore ratio of 1.4 with a displacement of 2156 cm3. All experiments have been conducted for stoichiometric operation at 2000 RPM. First, since compression ratio (CR) is directly related to the thermal efficiency, four CR were explored for operation without exhaust gas recirculation (EGR). Then, for the same four CR, EGR was used to suppress the knock occurrence at high loads, and its effect on initial and main combustion duration was compared. Second, the shape of intake port was revised to increase tumble flow for reducing combustion duration, and extending EGR-stability limit further. Then, as an effective method to ensure stable combustion for EGR-diluted stoichiometric operation, the use of twin spark ignition (SI) system is examined by modifying both valve diameters of intake and exhaust, and its effect is compared against that of single spark ignition. In addition, the layout of twin spark ignition was also examined for the location of front-rear and intake-exhaust. To get the maximum BTE at high load, 12 V electronic super charger (eSC) was applied. Under the condition of using 12 V eSC, the effect of intake cam duration was identified by increasing from 260 deg to 280 deg. Finally, 48 V eSC was applied with the longer intake camshaft duration of 280 deg. As a result, the maximum BTE of 44% can be achieved for stoichiometric operation with EGR.

Sign in / Sign up

Export Citation Format

Share Document