scholarly journals Analysis of the influence of the suspension parameters on the vehicle's oscillation

2018 ◽  
Author(s):  
S .S . Savvin ◽  
E. A. Neustroev
Keyword(s):  
Suspension Parameters

Metamodel-based robust collaborative optimization for the suspension parameters of rail vehicles

2019 ◽  
Vol 42 (8) ◽  
pp. 643-652
Author(s):  
Wenlong Liu ◽  
Yue Yang ◽  
Panpan Wang ◽  
Xiao Chen ◽  
Xiaobin Wei
Keyword(s):  
Collaborative Optimization ◽  
Suspension Parameters ◽  
Rail Vehicles

scholarly journals Design of a suspension system and determining suspension parameters of a medium downforce small Formula type car

2017 ◽  
Vol 124 ◽  
pp. 07006
Author(s):  
Sadjyot Biswal ◽  
Aravind Prasanth ◽  
R. Udayakumar ◽  
Shobhit Deva ◽  
Aman Gupta
Keyword(s):  
Suspension System ◽  
Suspension Parameters ◽  
Formula Type

Truck Suspension Design to Minimize Road Damage

1996 ◽  
Vol 210 (2) ◽  
pp. 95-107 ◽  
Author(s):  
D J Cole ◽  
D Cebon
Keyword(s):  
Three Dimensional ◽  
Fourth Power ◽  
Vehicle Model ◽  
Efficient Procedure ◽  
Suspension Parameters ◽  
Articulated Vehicle ◽  
Suspension Stiffness ◽  
Optimal Values ◽  
Dynamic Components ◽  
Stiffness And Damping

The objective of the work described in this paper is to establish guidelines for the design of passive suspensions that cause minimum road damage. An efficient procedure for calculating a realistic measure of road damage (the 95th percentile aggregate fourth power force) in the frequency domain is derived. Simple models of truck vibration are then used to examine the influence of suspension parameters on this road damage criterion and to select optimal values. It is found that to minimize road damage a suspension should have stiffness about one fifth of current air suspensions and damping up to twice that typically provided. The use of an anti-roll bar allows a high roll-over threshold without increasing road damage. It is thought that optimization in the pitch-plane should exclude correlation between the axles, to ensure that the optimized suspension parameters are robust to payload and speed changes. A three-dimensional ‘whole-vehicle’ model of an air suspended articulated vehicle is validated against measured tyre force histories. Optimizing the suspension stiffness and damping results in a 5.8 per cent reduction in road damage by the whole vehicle (averaged over three speeds). This compares with a 40 per cent reduction if the dynamic components of the tyre forces are eliminated completely.

Analysis, Design, and Optimization of High Speed Vehicle Suspensions Using State Variable Techniques

1974 ◽  
Vol 96 (2) ◽  
pp. 193-203 ◽  
Author(s):  
J. K. Hedrick ◽  
G. F. Billington ◽  
D. A. Dreesbach
Keyword(s):  
High Speed ◽  
Optimization Problems ◽  
Vertical Plane ◽  
Computer Application ◽  
Vehicle Suspension ◽  
State Variables ◽  
State Variable ◽  
Suspension Parameters ◽  
Suspension Model ◽  
High Speed Vehicle

This article applies state variable techniques to high speed vehicle suspension design. When a reasonably complex suspension model is treated, the greater adaptability of state variable techniques to digital computer application makes it more attractive than the commonly used integral transform method. A vehicle suspension model is developed, state variable techniques are applied, numerical methods are presented, and, finally, an optimization algorithm is chosen to select suspension parameters. A fairly complete bibliography is included in each of these areas. The state variable technique is illustrated in the solution of two suspension optimization problems. First, the vertical plane suspension of a high speed vehicle subject to guideway and aerodynamic inputs will be analyzed. The vehicle model, including primary and secondary suspension systems, and subject to both heave and pitch motions, has thirteen state variables. Second, the horizontal plane suspension of a high speed vehicle subject to guideway and lateral aerodynamic inputs is analyzed. This model also has thirteen state variables. The suspension parameters of both these models are optimized. Numerical results are presented for a representative vehicle, showing time response, mean square values, optimized suspension parameters, system eigenvalues, and acceleration spectral densities.

Using Parametric Simulation to Optimize Suspension Design

2003 ◽  
Author(s):  
G. Walter Rosenberger ◽  
Peter E. Klauser ◽  
George P. Binns ◽  
Gary P. Wolf
Keyword(s):  
Control Unit ◽  
Cost Effective ◽  
Parameter Analysis ◽  
Ride Quality ◽  
Worst Case ◽  
Suspension Parameters ◽  
History Of ◽  
Vehicle Response ◽  
Stiffness And Damping ◽  
Test Result

A project to design and implement suspension improvements to Amtrak’s F-40 Non-Powered Control Unit (NPCU) cars is described. The cars, built from former F-40 locomotives, had a history of poor ride quality. Rail Sciences Inc. (RSI) inspected one of the cab cars and measured its ride quality. Peter Klauser modeled the vehicle in NUCARS™ and validated the model against the test data. The vehicle response was primarily in pitch and bounce modes. To optimize the suspension, Klauser simulated vehicle response for a range of four suspension parameters: primary stiffness and damping, and secondary stiffness and damping. Nearly 2600 suspension combinations were considered. Simulation file setup and data analysis were performed automatically using parameter analysis software interacting with NUCARS™. The result was a five-dimensional response contour for each output variable, such as the engineer’s seat vertical and lateral accelerations, and car body acceleration. The most cost effective stiffness and damping parameters were selected from the response contour and translated into component specifications. RSI then provided Amtrak with new axle box springs and dampers, and re-tested the vehicle. The test result closely followed the predicted results from the simulation. Engineer’s seat vertical and cab lateral accelerations improved by 42% and 32% respectively for the worst-case conditions in the test territory.

scholarly journals Suspension parameter design of underframe equipment considering series stiffness of shock absorber

2020 ◽  
Vol 12 (5) ◽  
pp. 168781402092264
Author(s):  
Jie Chen ◽  
Yangjun Wu ◽  
Xiaolong He ◽  
Limin Zhang ◽  
Shijie Dong
Keyword(s):  
Simulation Software ◽  
Dynamics Simulation ◽  
Ride Quality ◽  
Railway Vehicle ◽  
Vibration Absorber ◽  
Dynamic Vibration Absorber ◽  
Suspension Parameters ◽  
Dynamic Vibration ◽  
Beam System ◽  
Element Type

In this article, a vertical rigid–flexible coupling model between the vehicle and the equipment is established. Considering the series stiffness of hydraulic shock absorbers, the underframe equipment is like a three-element-type Maxwell model dynamic vibration absorber. The carbody is approximated by an elastic beam and the three-element-type dynamic vibration absorber for general beam system was studied by fixed-point theory. The analytical solution of the optimal suspension parameters for the beam system subjected to harmonic excitation is obtained. The dynamic vibration absorber theory is applied to reduce the resonance of the carbody and to design the suspension parameters of the underframe equipment accordingly. Then, the railway vehicle model was established by multi-body dynamics simulation software, and the vibration levels of the vehicle at different speeds were calculated. A comparative analysis was made between the vehicles whose underframe equipment was suspended by the three-element-type dynamic vibration absorber model and the Kelvin–Voigt-type dynamic vibration absorber model, respectively. The results show that, compared with the vehicle whose underframe equipment is suspended by the Kelvin–Voigt-type dynamic vibration absorber model, the vehicle whose underframe equipment is suspended by the three-element-type dynamic vibration absorber model can achieve a much better ride quality and root mean square value of the vibration acceleration of the carbody. The carbody elastic vibration can be reduced and the vehicle ride quality can be improved effectively using the designed absorber.

Hunting Stability Analysis of a New High-Speed Railway Vehicle Model Moving on Curved Tracks

2007 ◽  
Author(s):  
Yung-Chang Cheng ◽  
Sen-Yung Lee
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Lateral Displacement ◽  
Creep Model ◽  
Railway Vehicle ◽  
Nonlinear Creep ◽  
Car Body ◽  
Suspension Parameters ◽  
Virtual Boundary ◽  
Hunting Stability

A new dynamic model of railway vehicle moving on curved tracks is proposed. In this new model, the motion of the car body is considered and the motion of the tuck frame is not restricted by a virtual boundary. Based on the heuristic nonlinear creep model, the nonlinear coupled differential equations of the motion of a fourteen degrees of freedom car system, considering the lateral displacement and the yaw angle of the each wheelset, the truck frame and the car body, moving on curved tracks are derived in completeness. To illustrate the accuracy of the analysis, the limiting cases are examined. In addition, the influences of the suspension parameters on the critical hunting speeds evaluated via the linear and the nonlinear creep models respectively are studied. Furthermore, the influences of the suspension parameters on the critical hunting speeds evaluated via the fourteen degrees of freedom car system and the six degrees of freedom truck system, which the motion of the tuck frame is restricted by a virtual boundary, are compared.

scholarly journals Effects of suspended micro- and nanoscale particles on zooplankton functional diversity of drainage system reservoirs at an open-pit mine

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Anna Maria Goździejewska ◽  
Monika Gwoździk ◽  
Sławomir Kulesza ◽  
Mirosław Bramowicz ◽  
Jacek Koszałka
Keyword(s):  
Functional Diversity ◽  
Drainage System ◽  
Open Pit ◽  
Nanoscale Particles ◽  
X Ray ◽  
Force Microscopy ◽  
Suspension Parameters ◽  
Atomic Force ◽  
Size Of Particles ◽  
The Impact

Abstract Water from mining drainage is turbid because of suspensions. We tested the hypothesis that the chemical composition as well as shape and size of particles in suspensions of natural origin affect the density and functional diversity of zooplankton. The suspensions were analyzed with atomic force microscopy (AFM), energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), and optical microscopy. Elements found in the beidellite clays were also identified in the mineral structure of the particles. As the size of the microparticles decreased, the weight proportions of phosphorus, sulfur, and chlorine increased in the suspensions. These conditions facilitated the biomass growth of large and small microphages and raptorials. As the size of the nanoparticles decreased, the shares of silicon, aluminum, iron, and magnesium increased. These conditions inhibited raptorials the most. Ecosystem functionality was the highest with intermediate suspension parameters, which were at the lower range of the microphase and the upper range of the nanophase. The functional traits of zooplankton demonstrate their potential for use as sensitive indicators of disruptions in aquatic ecosystems that are linked with the presence of suspensions, and they facilitate gaining an understanding of the causes and scales of the impact of suspensions.

Sign in / Sign up

Export Citation Format

Share Document