scholarly journals Nanosized Catalysts in the Process of Hydrogenating Acetylene

2018 ◽  
Vol 20 (3) ◽  
pp. 249 ◽  
Author(s):  
S.K. Tanirbergenova ◽  
N.K. Zhylybayeva ◽  
S.Zh. Tairabekova ◽  
D.A. Tugelbayeva ◽  
G.M. Naurzbayeva ◽  
...  
Keyword(s):  
Aluminum Oxide ◽  
High Temperatures ◽  
Reaction Temperature ◽  
Low Temperatures ◽  
Hydrogenation Reaction ◽  
Acetylene Hydrogenation ◽  
Waste Products ◽  
Nanosized Catalysts ◽  
Aluminum Activity ◽  
Optimum Reaction

Hydrogenating process of the acetylene to ethylene using automated flow catalytic installation at nanoscaled catalysts Ni, Co and carriers at a pressure of 5 atm was studied. The actions of carriers and nanosized catalysts during hydrogenation reaction of acetylene to ethylene at low temperatures in the range from 50–120 °С were analyzed. With ratio of С2Н2:Н2 being equal to (1:2), at 80 °С the aluminum oxide carrier exhibits an activity, conversion of acetylene makes up 70%, when using zeolite 3A it is 63%. When the temperature rises to 120 °С, the aluminum activity is decreasing and conversion is 53%. However, zeolite exhibits its activity at high temperatures, at a temperature of 120 °С conversion of acetylene reaches to 73.5%. It is shown that with increasing of hydrogen ratio, the ethylene yield increases from 5 to 10.7% using catalyst 5% Ni/3A. In addition, in reaction of acetylene hydrogenation there are not formed waste products. For this process, the optimum reaction temperature is 80 °С, feedstock ratio (1:3) is positive, where the ethylene yield increased up to 16.7% and at catalyst to 5% Co/3A.

Low solubility of alumina in enstatite and uncertainties in estimated palaeogeotherms

1978 ◽  
Vol 288 (1355) ◽  
pp. 471-486 ◽  
Keyword(s):  
High Temperatures ◽  
Low Temperatures ◽  
Alumina Content ◽  
Equilibrium Solubility ◽  
Low Solubility

Spurious kinks in estimated palaeogeotherms may result from small errors in the calibration of the geothermometers and geobarometers. New data indicate that the equilibrium solubility of alumina in enstatite is even less than shown by recent studies, and that the slopes (d T /d P ) of the isopleths of equal alumina content are steeper than hitherto believed. Consequently, pressures of equilibration estimated from current formulations of the orthopyroxene-garnet geobarometer will be too high at high temperatures (> 1200 °C) and too low at low temperatures.

scholarly journals Environmental temperature during early life affects the personality of mosquitofish in adulthood

2021 ◽  
Author(s):  
Haifeng Li ◽  
Xinyu ZHang ◽  
Yi Wu ◽  
Feng ZHang ◽  
CHunlin Li
Keyword(s):  
Body Length ◽  
High Temperatures ◽  
Low Temperatures ◽  
Early Life ◽  
Environmental Temperature ◽  
Phenotypic Trait ◽  
Behavioral Syndrome ◽  
Growing Up ◽  
Female Fish ◽  
Behavioral Traits

Abstract Personality has been observed in a variety of animal taxa with important implications in ecology and evolution. Exploring the influence of environmental temperature during early life on personality could help to understand the ontogeny of this phenotypic trait in animals. In this study, we reared newborn mosquitofish Gambusia affinis at high (30°C) and low (25°C) water temperatures and measured their shyness and exploration upon sexual maturity. We tested the repeatability of each behavioral trait; the correlation between them; and the effects of rearing temperature, sex, and body length on the behaviors. When growing up at low temperatures, female fish exhibited repeatability in shyness and exploration, and males exhibited marginal repeatability in shyness. However, neither of the 2 behaviors were repeatable when the fish were reared at high temperatures. There was a negative correlation between shyness and exploration, indicating that the 2 behaviors comprise a behavioral syndrome in this species. Mosquitofish reared at high temperatures were more explorative than those reared at low temperatures, while there was no difference in shyness between the 2 treatments. Body length and sex had no significant effects on the average values of the 2 behaviors. The results indicate that environmental temperature during early life could shape the personality of mosquitofish and modify the average of the behavioral traits. These findings might provide insights to understand the ontogeny of animal personality and how changes in environmental temperature influence animal dispersal by shaping their personality.

Analysis of Ferroelectric Microcapacitors by Scanning Probe Microscope

2004 ◽  
Vol 811 ◽  
Author(s):  
Nobuhiro Kin ◽  
Koichiro Honda
Keyword(s):  
High Temperatures ◽  
Low Temperatures ◽  
Evaluation System ◽  
Ferroelectric Material ◽  
Scanning Probe Microscope ◽  
Scanning Probe ◽  
Electrical Heater ◽  
Device Processing ◽  
Probe Microscope ◽  
The Impact

ABSTRACTTo develop higher density FRAM requires reducing cell size. Therefore, the size effects resulting from device processing and the material's physical properties must be measured. Therefore, analyzing the electric characteristics of a single bit cell capacitor has become important. Two known characteristics of ferroelectric material are that the Vc increases at low temperatures, and the Pr falls at high temperatures. To further evaluate the impact of temperature on ferroelectrics, we constructed a new evaluation system based on a scanning probe microscope, that can measure the electric characteristics of a single bit cell capacitor. This system can be used in the temperature range from −120 degrees to 300 degrees C. We accomplished this by circulating liquid nitrogen around a SPM stage and by using an electrical heater. We measured the electrical properties of ferroelectric microcapacitors by using a sample with IrOx/PZT/Pt structure. Our measurements revealed that 2Pr really increases at low temperatures, and Pr decreases at high temperatures. That is, we have shown that Vc increases 30% at low temperatures and Pr decreases 10% also in an actual FRAM single bit cell capacitor.

Effects of ternary additions on the deformation behavior of single crystals of MoSi2

2000 ◽  
Vol 646 ◽  
Author(s):  
Haruyuki Inui ◽  
Koji Ishikawa ◽  
Masaharu Yamaguchi
Keyword(s):  
Yield Strength ◽  
Strain Rate ◽  
Single Crystals ◽  
Creep Strain ◽  
High Temperatures ◽  
Low Temperatures ◽  
Deformation Behavior ◽  
Creep Strain Rate ◽  
Compression Creep ◽  
Ternary Additions

ABSTRACTEffects of ternary additions on the deformation behavior of single crystals of MoSi2 with the hard [001] and soft [0 15 1] orientations have been investigated in compression and compression creep. The alloying elements studied include V, Cr, Nb and Al that form a C40 disilicide with Si and W and Re that form a C11b disilicide with Si. The addition of Al is found to decrease the yield strength of MoSi2 at all temperatures while the additions of V, Cr and Nb are found to decrease the yield strength at low temperatures and to increase the yield strength at high temperatures. In contrast, the additions of W and Re are found to increase the yield strength at all temperatures. The creep strain rate for the [001] orientation is significantly lower than that for the [0 15 1] orientation. The creep strain rate for both orientations is significantly improved by alloying with ternary elements such as Re and Nb.

scholarly journals Optimization of Synthesis of Seleno-Sargassum fusiforme(Harv.) Setch. Polysaccharide by Response Surface Methodology, Its Characterization, and Antioxidant Activity

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Yu-Bin Ji ◽  
Fang Dong ◽  
Miao Yu ◽  
Long Qin ◽  
Dan Liu
Keyword(s):  
Antioxidant Activity ◽  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Reaction Temperature ◽  
Sargassum Fusiforme ◽  
Synthesis Conditions ◽  
Optimum Reaction ◽  
Series Of Experiments

The response surface methodology was employed to optimize the synthesis conditions of seleno-Sargassum fusiforme(Harv.) Setch. polysaccharide. Three independent variables (reaction time, reaction temperature, and ratio of Na2SeO3to SFPSI) were tested. Furthermore, the characterization and antioxidant activity of Se-SFPSIin vivowere investigated. The result showed that the actual experimental Se content of Se-SFPSI was 3.352 mg/g at the optimum reaction conditions of reaction time 8 h, reaction temperature 71°C, and ratio of Na2SeO3to SFPSIB 1.0 g/g. A series of experiments showed that the characterization of Se-SFPSIB was significantly different from that of SFPSIB. Additionally, antioxidant activity assay indicated that the Se-SFPSIB could increase catalase (CAT), superoxide dismutase (SOD), and glutathione peroxidase (GSH-Px) activity of mice bearing tumor S180in blood, heart, and liver while decreasing malondialdehyde (MDA) levels. It can be concluded that selenylation is a feasible approach to obtain seleno-polysaccharide which was utilized as highly biological medicine or functional food.

Consideration of the Cross-Anisotropy of Different Materials of the Asphalt Surface Layer and Temperature to Determine Pavement Responses

2021 ◽  
Vol 13 (1) ◽  
pp. 140-151
Author(s):  
Minrui Guo ◽  
Xinglin Zhou
Keyword(s):  
Surface Layer ◽  
High Temperatures ◽  
Low Temperatures ◽  
Compressive Strain ◽  
Fatigue Cracking ◽  
Element Model ◽  
Rate Of Change ◽  
Temperature Relationship ◽  
The Cross ◽  
Cross Anisotropy

The effects of the cross-anisotropy of different materials of the asphalt surface layer and the depth-temperature relationship on pavement responses and damage are investigated. A three-dimensional Finite-Element Model (FEM) of the pavement, which considers the depth-temperature relationship of the surface layer under moving tire load, is developed. Pavement damage models are established to evaluate the damage ratio for primary rutting and fatigue cracking. The results show that the compressive strain at the bottom of the surface layer increases as the temperature increases, and the cross-anisotropy (n-value) decreases, indicating that a decrease in the horizontal modulus of different materials of the surface layer increases the damage ratio for primary rutting at high temperatures. The tensile strain at the bottom of the surface layer declines as the n-value increases to 1. For the same change in the n-value, the rate of change of the damage ratio for fatigue cracking is greater at low temperatures than at high temperatures, demonstrating that the number of allowable load repetitions is more sensitive at low temperatures. In addition, the effect of cross-anisotropy and temperature on the vertical stress are larger on the top of the base than in the subbase and subgrade.

scholarly journals Transformation of 2-Butene into Propene on WO3/MCM-48: Metathesis and Isomerization of n-Butene

Catalysts ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 585 ◽  
Author(s):  
Derun Hua ◽  
Zheng Zhou ◽  
Qianqian Hua ◽  
Jian Li ◽  
Xinning Lu ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
High Temperatures ◽  
Thermodynamic Analysis ◽  
Reaction Temperature ◽  
Thermodynamic Calculations ◽  
Metathesis Reaction ◽  
Good Catalytic Activity

The metathesis of 2-butene (Trans and Cis) to propene was investigated over W-based catalysts. Thermodynamic calculations for metathesis and isomerization were carried out at various temperatures to test the reactions. The results showed that the WO3/MCM-48 catalyst had good catalytic activity. The metathesis activity depended on the acidity of the catalyst and the dispersity of the WO3 on the supports. High temperatures promoted the isomerization of 2-butene to 1-butene. According to thermodynamic analysis, however, this is adverse to the metathesis reaction, making it important to determine an appropriate reaction temperature.

scholarly journals MODIFIED COBALT CATALYSTS FOR HYDROGENATION OF HYDROCARBONS

2020 ◽  
Vol 18 (3) ◽  
pp. 156-161
Author(s):  
A.N. Aitugan ◽  
S.K. Tanirbergenova ◽  
Ye. Tileuberdi ◽  
D. Tugelbayeva
Keyword(s):  
Catalytic Activity ◽  
Aluminum Oxide ◽  
Process Parameters ◽  
Cobalt Catalyst ◽  
Cobalt Catalysts ◽  
Oxide Content ◽  
Acetylene Hydrogenation ◽  
Aluminum Oxides ◽  
Selective Hydrogenation Of Acetylene ◽  
Chemical Contents

This work is devoted to the study of the influence of aluminum oxide content on the activity of cobalt catalysts in the reaction of selective hydrogenation of acetylene to ethylene. Cobalt catalysts modified with aluminum oxide having size between 50 to 500 nm were synthesized. Chemical contents and structure of carrier were investigated.  The catalytic activity of 5 % Со /clay and 5% Co/SiAl catalysts at acetylene hydrogenation was studied in the temperature range 100-180 , with a ratio of 1:2 of acetylene and hydrogen. The ethylene yield is 87.8 % in modifying the cobalt catalyst with aluminum oxide, whereas with the same process parameters, the ethylene yield is 72 %. 5 % Cobalt catalysts modified with 1.5 % aluminum oxides are more active in hydrogenation acetylene process than 5 % Со /clay 450 ℃ catalyst.

scholarly journals Forging, textures, and deformation systems in a B2 FeAl alloy

1999 ◽  
Vol 14 (3) ◽  
pp. 715-728 ◽  
Author(s):  
P. Zhao ◽  
D. G. Morris ◽  
M. A. Morris Munoz
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Slip System ◽  
High Temperatures ◽  
Low Temperatures ◽  
High Speed ◽  
Deformation Texture ◽  
Slip Systems ◽  
Feal Alloy ◽  
Very High

High-temperature forging experiments have been carried out by axial compression testing on a Fe–41Al–2Cr alloy in order to determine the deformation systems operating under such high-speed, high-temperature conditions, and to examine the textures produced by such deformation and during subsequent annealing to recrystallize. Deformation is deduced to take place by the operation of 〈111〉 {110} and 〈111〉{112} slip systems at low temperatures and by 〈100〉{001} and 〈100〉{011} slip systems at high temperatures, with the formation of the expected strong 〈111〉 textures. The examination of the weak 〈100〉 texture component is critical to distinguishing the operating slip system. Both texture and dislocation analyses are consistent with the operation of these deformation systems. Recrystallization takes place extremely quickly at high temperatures (above 800 °C), that is within seconds after deformation and also dynamically during deformation itself. Recrystallization changes the texture such that 〈100〉 textures superimpose on the deformation texture. The flow stress peak observed during forging is found at a very high temperature. Possible origins of the peak are examined in terms of the operating slip systems.

Sign in / Sign up

Export Citation Format

Share Document