scholarly journals An Investigation of Spectral Efficiency in Linear MRC and MMSE Detectors with Perfect and Imperfect CSI for Massive MIMO Systems

2021 ◽  
Vol 38 (2) ◽  
pp. 495-501
Author(s):  
Indrajeet Kumar ◽  
Ritesh Kumar Mishra
Keyword(s):  
Antenna Arrays ◽  
Mimo Systems ◽  
Minimum Mean Square Error ◽  
Multiple Input Multiple Output ◽  
Antenna System ◽  
Base Station ◽  
Imperfect Csi ◽  
Detector Performance ◽  
Mmse Detector ◽  
Sum Rate

In this paper, the performance of two linear detectors in multi-user (MU) multiple-input multiple-output (MIMO) systems is investigated. The uplink sum rate and lower bound of channel capacity is derived for both maximum-ratio combination (MRC) and minimum mean square error (MMSE) schemes considering imperfect and perfect channel state information (CSI) conditions. Results show that linear detector performance improves dramatically when the number of base station (BS) users is smaller than that of BS antennas. It is being demonstrated that in the case of imperfect CSI and the number of BS antennas in the conditions of perfect CSI the transmitting power of users can be decreased by the square root of the number of BS antennas. Simulation results show that the MMSE detector outperforms the MRC detector. The results indicated that the system's uplink sum rate is increased by using significantly larger antenna arrays as opposed to just one antenna system. The findings of the Monte-Carlo simulation are very close to the analytical results.

scholarly journals An Improved Jacobi-Based Detector for Massive MIMO Systems

Information ◽  
2019 ◽  
Vol 10 (5) ◽  
pp. 165 ◽  
Author(s):  
Xiaoqing Zhao ◽  
Zhengquan Li ◽  
Song Xing ◽  
Yang Liu ◽  
Qiong Wu ◽  
...  
Keyword(s):  
Massive Mimo ◽  
Communication Systems ◽  
Mimo Systems ◽  
Minimum Mean Square Error ◽  
Multiple Input Multiple Output ◽  
Correction Method ◽  
Detection Algorithm ◽  
Detection Accuracy ◽  
Input Multiple Output ◽  
Mmse Detector

Massive multiple-input-multiple-output (MIMO) is one of the key technologies in the fifth generation (5G) cellular communication systems. For uplink massive MIMO systems, the typical linear detection such as minimum mean square error (MMSE) presents a near-optimal performance. Due to the required direct matrix inverse, however, the MMSE detection algorithm becomes computationally very expensive, especially when the number of users is large. For achieving the high detection accuracy as well as reducing the computational complexity in massive MIMO systems, we propose an improved Jacobi iterative algorithm by accelerating the convergence rate in the signal detection process.Specifically, the steepest descent (SD) method is utilized to achieve an efficient searching direction. Then, the whole-correction method is applied to update the iterative process. As the result, the fast convergence and the low computationally complexity of the proposed Jacobi-based algorithm are obtained and proved. Simulation results also demonstrate that the proposed algorithm performs better than the conventional algorithms in terms of the bit error rate (BER) and achieves a near-optimal detection accuracy as the typical MMSE detector, but utilizing a small number of iterations.

scholarly journals Parametric codebook design for efficient signal transmission using uniform circular arrays

2021 ◽  
Vol 2021 (1) ◽  
Author(s):  
Junsik Shin ◽  
Junyeub Suh ◽  
Sangchun Park ◽  
Wonjin Sung
Keyword(s):  
Antenna Arrays ◽  
Channel Model ◽  
Mimo Systems ◽  
Signal Transmission ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Step Size ◽  
Codebook Design ◽  
Construction Methods ◽  
Planar Array

AbstractIn order to improve the quality of the received signal and system spectral efficiency, accurate beamforming using a given antenna array is essential for multiple-input multiple-output (MIMO) systems. To obtain desired MIMO transmission performance, construction of codebooks which are composed of matching beamforming vectors to the array structure is important. To effectively cover different types of mobile traffic, the base station for 5G new radio employs antenna arrays in various sizes and shapes. Nevertheless, the codebooks adopted by the 3GPP standard so far are based on the uniform linear array and the uniform planar array, necessitating design techniques for a wider class of antenna arrays. In this paper, we propose codebook construction methods for the uniform circular array with parameters to flexibly set the initial phase and step size based on the channel characteristics of the user equipment (UE). When tested over the 3GPP spatial channel model, the proposed codebooks show a substantial amount of gain over the conventional codebooks in all UE locations within the cell.

scholarly journals Sum-Rate of Multi-User MIMO Systems with Multi-Cell Pilot Contamination in Correlated Rayleigh Fading Channel

Entropy ◽  
2019 ◽  
Vol 21 (6) ◽  
pp. 573 ◽  
Author(s):  
Menghan Wang ◽  
Dongming Wang
Keyword(s):  
Rayleigh Fading ◽  
Gaussian Approximation ◽  
Mimo Systems ◽  
Mimo System ◽  
Multiple Input Multiple Output ◽  
Moment Generating Function ◽  
Base Station ◽  
Pilot Contamination ◽  
Input Multiple Output ◽  
Sum Rate

This paper presents some exact results on the sum-rate of multi-user multiple-input multiple-output (MU-MIMO) systems subject to multi-cell pilot contamination under correlated Rayleigh fading. With multi-cell multi-user channel estimator, we give the lower bound of the sum-rate. We derive the moment generating function (MGF) of the sum-rate and then obtain the closed-form approximations of the mean and variance of the sum-rate. Then, with Gaussian approximation, we study the outage performance of the sum-rate. Furthermore, considering the number of antennas at base station becomes infinite, we investigate the asymptotic performance of the sum-rate. Theoretical results show that compared to MU-MIMO system with perfect channel estimation and no pilot contamination, the variance of the sum-rate of the considered system decreases very quickly as the number of antennas increases.

scholarly journals Sum Rate Analysis of MU-MIMO with a 3D MIMO Base Station Exploiting Elevation Features

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Xingwang Li ◽  
Lihua Li ◽  
Fupeng Wen ◽  
Junfeng Wang ◽  
Chao Deng
Keyword(s):  
Channel Model ◽  
Mimo Systems ◽  
Multiple Input Multiple Output ◽  
Three Dimensional ◽  
Base Station ◽  
Rate Performance ◽  
High Rise ◽  
Rate Analysis ◽  
Input Multiple Output ◽  
Sum Rate

Although the three-dimensional (3D) channel model considering the elevation factor has been used to analyze the performance of multiuser multiple-input multiple-output (MU-MIMO) systems, less attention is paid to the effect of the elevation variation. In this paper, we elaborate the sum rate of MU-MIMO systems with a 3D base station (BS) exploiting different elevations. To illustrate clearly, we consider a high-rise building scenario. Due to the floor height, each floor corresponds to an elevation. Therefore, we can analyze the sum rate performance for each floor and discuss its effect on the performance of the whole building. This work can be seen as the first attempt to analyze the sum rate performance for high-rise buildings in modern city and used as a reference for infrastructure.

Antenna tilt optimization for multi-cell massive multiple-input multiple-output (MIMO) systems with two tilts

Frequenz ◽  
2020 ◽  
Vol 74 (9-10) ◽  
pp. 359-368
Author(s):  
Deming Chu ◽  
Anzhong Hu
Keyword(s):  
Lower Bound ◽  
Antenna Arrays ◽  
Mimo Systems ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Perfect Channel State Information ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Output System ◽  
Antenna Tilt

AbstractIn this paper, we study the optimization of two tilt angles corresponding to two antenna arrays in each base station (BS) of a massive multiple-input multiple-output system. We consider two scenarios with perfect channel state information (CSI) and imperfect CSI. In the limit of the number of the BS antennas, the channel orthogonality is employed to derive the limit and the lower bound of the throughputs. By maximizing the lower bound or the limit throughput, the two antenna tilt angles are optimized. Simulation results show that the throughput performance can be improved with the designed tilt angles.

scholarly journals Accurate Performance Analysis of Coded Large-Scale Multiuser MIMO Systems with MMSE Receivers

Sensors ◽  
2019 ◽  
Vol 19 (13) ◽  
pp. 2884 ◽  
Author(s):  
Kai Zhai ◽  
Zheng Ma ◽  
Xianfu Lei
Keyword(s):  
Large Scale ◽  
Mimo Systems ◽  
Minimum Mean Square Error ◽  
Multiple Input Multiple Output ◽  
Path Loss ◽  
Base Station ◽  
Mimo Networks ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Accurate Performance

In this paper, we estimate the uplink performance of large-scale multi-user multiple-input multiple-output (MIMO) networks. By applying minimum-mean-square-error (MMSE) detection, a novel statistical distribution of the signal-to-interference-plus-noise ratio (SINR) for any user is derived, for path loss, shadowing and Rayleigh fading. Suppose that the channel state information is perfectly known at the base station. Then, we derive the analytical expressions for the pairwise error probability (PEP) of the massive multiuser MMSE–MIMO systems, based on which we further obtain the upper bound of the bit error rate (BER). The analytical results are validated successfully through simulations for all cases.

scholarly journals Energy Efficient Linear and Non-Linear Precoders for Massive MIMO Systems

2020 ◽  
Vol 8 (8) ◽  
pp. 59-66
Author(s):  
Samson Hansen Sackey ◽  
Michael Kwame Ansong ◽  
Samuel Nartey Kofie ◽  
Abdul Karim Armahy
Keyword(s):  
Energy Efficiency ◽  
Massive Mimo ◽  
Large Scale ◽  
Mimo Systems ◽  
Minimum Mean Square Error ◽  
Multiple Input Multiple Output ◽  
Antenna System ◽  
Dirty Paper Coding ◽  
Multiple Input ◽  
Non Linear

The term Massive MIMO means, Massive multiple input multiple output also known as (large-scale antenna system, very large MIMO). Massive Multiple-Input-MultipleOutput (MIMO) is the major key technique for the future Fifth Generation (5G) of mobile wireless communication network due to its characteristics, elements and advantages. Massive MIMO will be comprised of five major elements; antennas, electronic components, network architectures, protocols and signal processing. We realize that precoding technique is a processing technique that utilizes Channel State Information Technique (CSIT) by operating on the signals before transmitting them. This technique varies base on the type of CSIT and performance criterion. Precoding technique is the last digital processing block at the transmitting side. In this paper, linear and non-linear Precoding technique was reviewed and we proposed two techniques under each that is Minimum Mean Square Error (MMSE), Block Diagonalization (BD), Tomlinson-Harashima (TH) and Dirty paper coding (DPC). Four Precoding techniques: MMSE, BD, DPC and TH were used in the studies to power consumption, energy efficiency and area throughput for single-cell and multi-cell scenarios. In comparing the proposed techniques, in terms of energy efficiency and area throughput, reuse factor (Reuse 4) performs better than other techniques when there is an imperfect CSI is used

scholarly journals A Graphene-Assembled Film Based MIMO Antenna Array with High Isolation for 5G Wireless Communication

2021 ◽  
Vol 11 (5) ◽  
pp. 2382
Author(s):  
Rongguo Song ◽  
Xiaoxiao Chen ◽  
Shaoqiu Jiang ◽  
Zelong Hu ◽  
Tianye Liu ◽  
...  
Keyword(s):  
Antenna Array ◽  
Antenna Arrays ◽  
Multiple Input Multiple Output ◽  
Frequency Selective Surface ◽  
Antenna System ◽  
Antenna Element ◽  
Mimo Antenna ◽  
High Isolation ◽  
Input Multiple Output ◽  
Alternative Material

With the development of 5G, Internet of Things, and smart home technologies, miniaturized and compact multi-antenna systems and multiple-input multiple-output (MIMO) antenna arrays have attracted increasing attention. Reducing the coupling between antenna elements is essential to improving the performance of such MIMO antenna system. In this work, we proposed a graphene-assembled, as an alternative material rather than metal, film-based MIMO antenna array with high isolation for 5G application. The isolation of the antenna element is improved by a graphene assembly film (GAF) frequency selective surface and isolation strip. It is shown that the GAF antenna element operated at 3.5 GHz has the realized gain of 2.87 dBi. The addition of the decoupling structure improves the isolation of the MIMO antenna array to more than 10 dB and corrects the antenna radiation pattern and operating frequency. The isolation between antenna elements with an interval of 0.4λ is above 25 dB. All experimental results show that the GAF antenna and decoupling structure are efficient devices for 5G mobile communication.

scholarly journals Low-complexity sparse-aware multiuser detection for large-scale MIMO systems

2021 ◽  
Vol 2021 (1) ◽  
Author(s):  
Rong Ran ◽  
Hayoung Oh
Keyword(s):  
Large Scale ◽  
Mimo Systems ◽  
Minimum Mean Square Error ◽  
Multiple Input Multiple Output ◽  
Low Complexity ◽  
Finite Alphabet ◽  
Multiuser Detectors ◽  
Input Multiple Output ◽  
Error Detector ◽  
Significant Performance

AbstractSparse-aware (SA) detectors have attracted a lot attention due to its significant performance and low-complexity, in particular for large-scale multiple-input multiple-output (MIMO) systems. Similar to the conventional multiuser detectors, the nonlinear or compressive sensing based SA detectors provide the better performance but are not appropriate for the overdetermined multiuser MIMO systems in sense of power and time consumption. The linear SA detector provides a more elegant tradeoff between performance and complexity compared to the nonlinear ones. However, the major limitation of the linear SA detector is that, as the zero-forcing or minimum mean square error detector, it was derived by relaxing the finite-alphabet constraints, and therefore its performance is still sub-optimal. In this paper, we propose a novel SA detector, named single-dimensional search-based SA (SDSB-SA) detector, for overdetermined uplink MIMO systems. The proposed SDSB-SA detector adheres to the finite-alphabet constraints so that it outperforms the conventional linear SA detector, in particular, in high SNR regime. Meanwhile, the proposed detector follows a single-dimensional search manner, so it has a very low computational complexity which is feasible for light-ware Internet of Thing devices for ultra-reliable low-latency communication. Numerical results show that the the proposed SDSB-SA detector provides a relatively better tradeoff between the performance and complexity compared with several existing detectors.

scholarly journals Beam division multiple access for millimeter wave massive MIMO: Hybrid zero-forcing beamforming with user selection

2022 ◽  
Vol 12 (1) ◽  
pp. 445
Author(s):  
Hong Son Vu ◽  
Kien Truong ◽  
Minh Thuy Le
Keyword(s):  
Multiple Access ◽  
Mimo Systems ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Zero Forcing ◽  
Multiuser Interference ◽  
Novel Approach ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Promising Solution

<p>Massive multiple-input multiple-output (MIMO) systems are considered a promising solution to minimize multiuser interference (MUI) based on simple precoding techniques with a massive antenna array at a base station (BS). This paper presents a novel approach of beam division multiple access (BDMA) which BS transmit signals to multiusers at the same time via different beams based on hybrid beamforming and user-beam schedule. With the selection of users whose steering vectors are orthogonal to each other, interference between users is significantly improved. While, the efficiency spectrum of proposed scheme reaches to the performance of fully digital solutions, the multiuser interference is considerably reduced.</p>

Sign in / Sign up

Export Citation Format

Share Document