scholarly journals Three-Dimensional Numerical Simulation of a Flat Plate Solar Collector with Double Paths

2021 ◽  
Vol 39 (4) ◽  
pp. 1087-1096
Author(s):  
Mohammed Amine Amraoui
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Solar Collector ◽  
Three Dimensional ◽  
Heat Transfer Fluid ◽  
Minimal Cost ◽  
Solar Collectors ◽  
Flat Plate Solar Collector ◽  
Exchange Surface ◽  
Calculation Code

Flat air solar collectors are used for heat transfer between the absorber and the heat transfer fluid, to improve this transfer there are several methods. Among these methods, the exchange surface lengthening and the creation of turbulence. In this work is done to give a comparison between two types of solar collectors, so we have made an improvement of Ben Slama Romdhane's solar collector by creating two air flow passages to increase heat transfer. We made a 3D simulation of a flat air solar collector with transverse baffles which causes turbulence and increases the exchange surface; we use the ANSYS calculation code to make the simulation and gives results with a brief time and minimal cost.

scholarly journals The numerical simulation of enhanced heat transfer on a Linear Fresnel molten salt-type receiver tube filled with porous media

2019 ◽  
Vol 118 ◽  
pp. 01041
Author(s):  
Chenggang Yang ◽  
Yuning Zhang ◽  
Fenghe Yan ◽  
Wenguang Zhang ◽  
Wei Li
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Numerical Simulation ◽  
Porous Media ◽  
Molten Salt ◽  
Temperature Difference ◽  
Wall Temperature ◽  
Three Dimensional ◽  
Heat Transfer Fluid ◽  
Filling Rate

In this paper, three-dimensional numerical simulation was taken on a Linear Fresnel solar receiver tube using molten salt as heat transfer fluid (HTF), in which the porous media was filled to enhance the heat transfer efficiency. The simulation was to analyze the influence of the different conditions (filling rate, porosity and thermal conductivity) on heat transfer effect and wall temperature difference. The results revealed that the Nu (Nusselt number) increased firstly and then decreased with the increasing filling rate in both center filling and annular filling types. The optimal thermal performance were obtained when filling rate were 0.8 and 0.2 in center filling and annular filling, respectively. The Nu were about 1.7 and 1.5 times as the clear receiver. The circumferential temperature difference decreased firstly and then increased with filling rate increasing in both center filling and annular filling types. The lowest circumferential temperature differences were achieved at the filling rate 0.8 and 0.4 in center filling and annular filling types, and temperature difference decreased 15.88°C and 22°C compared with clear receiver, respectively. The Nu and PEC both decreased with porosity increasing. However, the thermal conductivity of porous media had little influence to the Nu and circumferential wall temperature.

Gas radiative effects on gas-filled flat plate solar collectors

2019 ◽  
Vol 97 (10) ◽  
pp. 1115-1124 ◽  
Author(s):  
Khosro Lari ◽  
Ali Tarokh ◽  
Mohammad Naghizadeh
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Air Temperature ◽  
Solar Collector ◽  
Hot Water ◽  
Discrete Ordinates ◽  
Solar Collectors ◽  
Radiative Effects ◽  
Wide Range ◽  
Flat Plate Solar Collector

A standard thermal solar collector can be used for both hot water production and air heating purposes. Gas-filled solar collectors represent a new emerging design approach with enhanced characteristics. In this research, numerical modeling is utilized to study radiative effects of the participating gases on the performance of solar collectors. The coupled radiative–convective heat transfer in the solar collector is considered and the collector cavity is considered as a radiatively participating medium. The finite volume method has been adopted to solve the governing equations and discrete ordinates method is used for radiative transfer. After validating the model used in this study, it is used to obtain the heat transfer characteristics of a flat-plate solar collector with real solar conditions of the city of Kerman, Iran, in summer at a wide range of air absorption coefficients. According to the results, by increasing the absorption coefficient of the air, the temperature of the absorber plate is reduced and the air temperature is increased, but the increase of air temperature is much higher than the reduction of absorber temperature. Hence, it is concluded that it is possible to use participating gases in the solar air heaters to enhance the performance of the collector.

Sign in / Sign up

Export Citation Format

Share Document