scholarly journals Numerical Analysis of the Influence of Geometry on a Large Scale Onshore Oscillating Water Column Device with Associated Seabed Ramp

2020 ◽  
Vol 15 (6) ◽  
pp. 873-884
Author(s):  
Max Letzow ◽  
Giulio Lorenzini ◽  
Dante Vinícius Eloy Barbosa ◽  
Ricardo Gabriel Hübner ◽  
Luiz Alberto Oliveira Rocha ◽  
...  
Keyword(s):  
Water Column ◽  
Degrees Of Freedom ◽  
Large Scale ◽  
Volume Fraction ◽  
Design Method ◽  
Length Ratio ◽  
Oscillating Water Column ◽  
Two Phase ◽  
Worst Case ◽  
Vof Model

The current study aims to perform a geometrical investigation of an onshore Oscillating Water Column (OWC) on a large scale. The Constructal Design method is employed, aiming to maximize its available power. The OWC is subjected to two constraints (areas of the chamber and ramp below the chamber); and three degrees of freedom: height/length ratio of the chamber (H1/L1), height/length ratio of the ramp (H2/L2), and submersion of the frontal wall of the chamber (H3). A laminar, unsteady, incompressible, and two-phase flow was adopted, solving conservation equations of mass, momentum, and transport of water-air volume fraction using Finite Volume Method (FVM) and Volume of Fluid (VOF) model. The global optimal geometry led to a twice maximized available power 37.3% higher than the best case without the seabed ramp below the chamber and seven times better than the worst case. Concerning the sensibility of geometry, results indicated that the chamber geometry, given by ratio H1/L1, over the available power (P) was strongly affected by the ramp ratio H2/L2. Moreover, the behavior of the effect of H2/L2 over the once maximized available power (Pm) and corresponding optimal shape of the chamber, (H1/L1)o, changed dramatically for two different magnitudes of H3 investigated.

Numerical and Geometrical Analysis of the Onshore Oscillating Water Column Wave Energy with a Ramp

2021 ◽  
Vol 412 ◽  
pp. 11-26
Author(s):  
Marla Rodrigues Oliveira ◽  
Elizaldo Domingues Santos ◽  
Liércio André Isoldi ◽  
Luiz Alberto Oliveira Rocha ◽  
Mateus das Neves Gomes
Keyword(s):  
Water Column ◽  
Wave Energy ◽  
Degrees Of Freedom ◽  
Design Method ◽  
Geometric Analysis ◽  
Relative Difference ◽  
Front Wall ◽  
Multiphase Model ◽  
Oscillating Water Column ◽  
Worst Case

This study is about a two-dimensional numerical analysis of the influence of a ramp in front on an oscillating water column wave energy converter (OWC-WEC). The main purpose was to evaluate, numerically and geometrically, the effect of using a ramp variation in relation to the frontal wall on the hydropneumatic power of the OWC-WEC. The constructal design method was applied for geometric analysis. The problem had a geometric constraint: the area of the ramp (A2) and two degrees of freedom: H2 / L2 (ratio of the height and length of the ramp) and L4 (the distance of the ramp concerning the OWC-WEC front wall). In numerical simulations, the equations of conservation of mass, momentum, and an equation for the transport of volumetric fraction were solved using the finite volume method (FVM). The multiphase model volume of fluid (VOF) was applied for the air-water interaction. Thus, the increase in the H2/L2 ratio resulted in a decrease of the root mean square (RMS) of the available hydropneumatic power (Phyd). By varying the distance L4, the better case was = 6 m and / = 0.025 and the worst case was = 1 m and / = 0.2. The relative difference between the better RMS Phyd = 150.7957 W and the worst Phyd = 73.1164 W reached up to a hundred and six percent.

Analysis of Geometric Variation of Three Degrees of Freedom through the Constructal Design Method for a Oscillating Water Column Device with Double Hidropneumatic Chamber

2019 ◽  
Vol 396 ◽  
pp. 22-31
Author(s):  
Yuri T.B. Lima ◽  
Mateus das Neves Gomes ◽  
Camila F. Cardozo ◽  
Liércio André Isoldi ◽  
Elizaldo D. Santos ◽  
...  
Keyword(s):  
Water Column ◽  
Degrees Of Freedom ◽  
Numerical Study ◽  
Design Method ◽  
Geometric Optimization ◽  
Oscillating Water Column ◽  
Constructal Design ◽  
Wave Energy Converters ◽  
Volume Method ◽  
Geometric Variation

This paper presents a biphasic two-dimensional numerical study of sea wave energy converters with operating principle being Oscillating Water Column (CAO) devices with two couples chambers. For the study of the geometric optimization, the Constructal Design method is applied in association with the exhaustive search method to determine the geometric arrangement that leads to the greatest hydropneumatic power available. The objective function is the maximization of hydropneumatic power converted by the device. The constraints of the problem are the inflow volumes of the hydropneumatic chamber (VE1, VE2), the total volumes (VT1, VT2) and the thicknesses of the device columns (e1, e3). The degrees of freedom analyzed were H1/L1(ratio between height and length of the hydropneumatic chamber of the first device), H2/L2 (ratio between height and length of the hydropneumatic chamber of the second device), H2 (height of the column dividing the two devices) and e2 (thickness of the column dividing the devices). In the present work the degree of freedom H6 (depth of immersion of the device) is kept constant and equal to H6 = 9.86 m. The Finite Volume Method (FVM) was used in the numerical solution of the equations employed. For the treatment of the interaction between the air and water phases, the Volume of Fluid (VOF) method was applied. The results show that the maximum hydropneumatic power available was 5715.2 W obtained for degrees of freedom H1/L1 = H2/L2 = 0.2613 and e2 = 2.22 m. The case of lower performance has a power value equal to 4818.5 W with degrees of freedom equal to H1/L1 = H2/L2 = 0.2613 and e2 = 0.1 m.

Evaluation of 3-D Computational Model of Oscillating Water Column Converter with Constructal Design with Three Degrees of Freedom and Limited Chimney Height

2021 ◽  
Vol 407 ◽  
pp. 128-137
Author(s):  
Vinícius Bloss ◽  
Camila Fernandes Cardozo ◽  
Flávia Schwarz Franceschini Zinani ◽  
Luiz Alberto Oliveira Rocha
Keyword(s):  
Water Column ◽  
Wave Energy ◽  
Degrees Of Freedom ◽  
Numerical Study ◽  
Mechanical Energy ◽  
Ocean Waves ◽  
Response Surfaces ◽  
Oscillating Water Column ◽  
Promising Source ◽  
Three Degrees Of Freedom

Theoretically, ocean waves contain enough mechanical energy to supply the entire world’s demand and, as of late, are seen as a promising source of renewable energy. To this end, several different technologies of Wave Energy Converters (WEC) have been developed such as Oscillating Water Column (OWC) devices. OWCs are characterized by a chamber in which water oscillates inside and out in a movement similar to that of a piston. This movement directs air to a chimney where a turbine is attached to convert mechanical energy. The analysis conducted was based on the Constructive Design Method, in which a numerical study was carried out to obtain the geometric configuration that maximized the conversion of wave energy into mechanical energy. Three degrees of freedom were used: the ratio of height to length of the hydropneumatic chamber (H1/L), the ratio of the height of the chimney to its diameter (H2/d) and the ratio of the width of the hydropneumatic chamber to the width of the wave tank (W/Z). A Design of Experiments (DoE) technique coupled with Central Composite Design (CCD) allowed the simulation of different combinations of degrees of freedom. This allowed the construction of Response Surfaces and correlations for the efficiency of the system depending on the degrees of freedom (width and height of the chamber), as well as the optimization of the system based on the Response Surfaces.

3D MС Simulation of Grain Growth Kinetics and the Zener Limit in Polycrystals

2014 ◽  
Vol 598 ◽  
pp. 8-12
Author(s):  
K.R. Phaneesh ◽  
Anirudh Bhat ◽  
Gautam Mukherjee ◽  
Kishore T. Kashyap
Keyword(s):  
Monte Carlo ◽  
Grain Growth ◽  
Growth Kinetics ◽  
Large Scale ◽  
Volume Fraction ◽  
Growth Exponent ◽  
Cube Root ◽  
Second Phase ◽  
Two Phase ◽  
Second Phase Particles

Large scale Potts model Monte Carlo simulation was carried on 3-dimensional square lattices of 1003 and 2003 sizes using the Metropolis algorithm to study grain growth behavior. Simulations were carried out to investigate both growth kinetics as well as the Zener limit in two-phase polycrystals inhibited in growth by second phase particles of single-voxel size. Initially the matrices were run to 10,000 Monte Carlo steps (MCS) to check the growth kinetics in both single phase and two-phase poly-crystals. Grain growth exponent values obtained as a result have shown to be highest (~ 0.4) for mono-phase materials while the value decreases with addition of second phase particles. Subsequently the matrices were run to stagnation in the presence of second phase particles of volume fractions ranging from 0.001to 0.1. Results obtained have shown a cube root dependence of the limiting grain size over the particle volume fraction thus reinforcing earlier 3D simulation efforts. It was observed that there was not much difference in the values of either growth kinetics or the Zener limit between 1003 and 2003 sized matrices, although the results improved mildly with size.

Numerical Simulation of Black Liquor Spray Characteristics

2002 ◽  
Author(s):  
Thomas D. Foust ◽  
Kurt D. Hamman ◽  
Brent A. Detering
Keyword(s):  
Droplet Size ◽  
Volume Fraction ◽  
Numerical Study ◽  
Black Liquor ◽  
Flow Distribution ◽  
Physical Models ◽  
Spray Characteristics ◽  
Two Phase ◽  
Vof Model ◽  
Sheet Breakup

The performance and capacity of Kraft recovery boilers is sensitive to black liquor velocity, droplet size and flow distribution in the furnace. Studies have shown that controlling droplet size and flow distribution improves boiler efficiency while allowing increased flight drying and devolatilization, and decreased carryover. The purpose of this study is to develop a robust two-phase numerical model to predict black liquor splashplate nozzle spray characteristics. A three-dimensional time dependent numerical study of black liquor sheet formation and sheet breakup is described. The volume of fluid (VOF) model is used to simulate flow through the splashplate nozzle up to initial sheet breakup and droplet formation. The VOF model solves the conservation equations of volume fraction and momentum utilizing the finite volume technique. Black liquor velocity, droplet size and flow distribution over a range of operating parameters are simulated using scaled physical models of splashplate nozzles. The VOF model is compared to results from a flow visualization experiment and experimental data found in the literature. The details of the simulation and experimental results are presented.

scholarly journals Large-scale experiments on the behaviour of a generalised Oscillating Water Column under random waves

2016 ◽  
Vol 99 ◽  
pp. 875-887 ◽  
Author(s):  
Antonino Viviano ◽  
Stefania Naty ◽  
Enrico Foti ◽  
Tom Bruce ◽  
William Allsop ◽  
...  
Keyword(s):  
Water Column ◽  
Large Scale ◽  
Oscillating Water Column ◽  
Random Waves

Experimental Study the Performance of a Compact Mooring System for a Dual Chamber Floating Oscillating Water Column Device

2020 ◽  
Author(s):  
Sheng Xu ◽  
K. Rezanejad ◽  
Shan Wang ◽  
J. F. M. Gadelho ◽  
C. Guedes Soares
Keyword(s):  
Water Column ◽  
Wave Energy ◽  
Degrees Of Freedom ◽  
Wave Energy Converter ◽  
Air Pressure ◽  
Mooring System ◽  
Oscillating Water Column ◽  
Energy Converter ◽  
Six Degrees Of Freedom ◽  
Motion Responses

Abstract A compact mooring system concept is proposed. This novel mooring is composed of submerged buoy and three segments of nylon ropes, which is suitable for the large wave energy converters and wave energy converter array due to its high flexibility and small mooring radius. The performance of this mooring concept was studied experimentally when it was moored to an oscillating water column. The damping of the oscillating water column was modelled by an orifice on top of the chamber. Both regular and irregular head sea wave tests were conducted. In order to study the influence of wave height on system dynamics, two series of regular wave tests with same periods but different wave heights were conducted. An optical tracking system was installed to capture six degrees of freedom motion responses of oscillating water column. The air pressure in the chamber was measured by the air pressure sensor. Two load cells were installed on the top of mooring lines to measure mooring tension time series. Besides, the wave surface elevations inside the chamber were measured by the wave gauges. According to the experimental results, the six degrees of freedom motion responses of floating wave energy converter and mooring tensions are analyzed. Besides, the energy conversion efficiency is evaluated based on the measured data.

Influence of Jordanian zeolite on the performance of a solar still: experiments and CFD simulation studies

2016 ◽  
Vol 16 (6) ◽  
pp. 1700-1709 ◽  
Author(s):  
Yazan Taamneh
Keyword(s):  
Experimental Data ◽  
Phase Change ◽  
Cfd Simulation ◽  
Volume Fraction ◽  
Solar Still ◽  
Cfd Simulations ◽  
Two Phase ◽  
Vof Model ◽  
Computational Fluid Dynamics Cfd ◽  
Good Agreement

Computational fluid dynamics (CFD) simulations were performed for experiments carried out with two identical pyramid-shaped solar stills. One was filled with Jordanian zeolite-seawater and the second was filled with seawater only. This work is focused on CFD analysis validation with experimental data conducted using a model of phase change interaction (evaporation-condensation model) inside the solar still. A volume-of-fluid (VOF) model was used to simulate the inter phase change through evaporation-condensation between zeolite-water and water vapor inside the two solar stills. The effect of the volume fraction of the zeolite particles (0 ≤ ϕ ≤ 0.05) on the heat and distillate yield inside the solar still was investigated. Based on the CFD simulation results, the hourly quantity of freshwater showed a good agreement with the corresponding experimental data. The present study has established the utility of using the VOF two phase flow model to provide a reasonable solution to the complicated inter phase mass transfer in a solar still.

scholarly journals Numerical study of fixed Oscillating Water Column with RANS-type two-phase CFD model

2017 ◽  
Vol 102 ◽  
pp. 294-305 ◽  
Author(s):  
Thomas Vyzikas ◽  
Samy Deshoulières ◽  
Olivier Giroux ◽  
Matthew Barton ◽  
Deborah Greaves
Keyword(s):  
Water Column ◽  
Numerical Study ◽  
Oscillating Water Column ◽  
Cfd Model ◽  
Two Phase

scholarly journals 3D NUMERICAL ANALYSIS ABOUT THE SHAPE INFLUENCE OF THE HYDRO-PNEUMATIC CHAMBER IN AN OSCILLATING WATER COLUMN (OWC)

2015 ◽  
Vol 14 (1) ◽  
pp. 03
Author(s):  
L. A. Isoldi ◽  
J. Do A. M. Grimmler ◽  
M. Letzow ◽  
J. A. Souza ◽  
M. Das N. Gomes ◽  
...  
Keyword(s):  
Water Column ◽  
Energy Demand ◽  
Air Flow ◽  
Electrical Energy ◽  
Oscillating Water Column ◽  
Ocean Energy ◽  
Electric Generator ◽  
Vof Model ◽  
Pneumatic Chamber ◽  
Shape Influence

The oceans represent one of the major energy natural resources, which potentially can be used to supply the World energy demand. In the last decades some devices to convert the wave ocean energy into electrical energy have been studied. In this work the operating principle of an Oscillating Water Column (OWC) converter was analyzed with a transient 3D numerical methodology, using the Finite Volume Method (FVM) and the Volume of Fluid (VOF) model. The incident waves on the OWC hydro- pneumatic chamber cause an oscillation of the water column inside the chamber producing an alternate air flow through the chimney. The air drives a turbine that is coupled to an electric generator. The aim of this work was to investigate the shape influence of the hydro-pneumatic chamber geometry in the air flow. For this, six cases were studied in laboratory scale and the results showed that the variation of the OWC chamber shape can improve 12.4% the amount of mass air flow.

Sign in / Sign up

Export Citation Format

Share Document