scholarly journals Forced Response and Stability of Flexible Rotor-Bearing Systems with Squeeze Film Dampers

2013 ◽  
Author(s):  
Feng He
Keyword(s):  
Forced Response ◽  
Squeeze Film ◽  
Flexible Rotor ◽  
Squeeze Film Dampers ◽  
Rotor Bearing

Nonlinear Analysis of Rotor-Bearing Systems Using Component Mode Synthesis

1983 ◽  
Vol 105 (3) ◽  
pp. 606-614 ◽  
Author(s):  
H. D. Nelson ◽  
W. L. Meacham ◽  
D. P. Fleming ◽  
A. F. Kascak
Keyword(s):  
Forced Response ◽  
Component Mode Synthesis ◽  
Squeeze Film ◽  
System Response ◽  
Reduced Order ◽  
Squeeze Film Dampers ◽  
Rotor Bearing ◽  
System Equations ◽  
Transient System ◽  
Blade Loss

The method of component mode synthesis is developed to determine the forced response of nonlinear, multishaft, rotor-bearing systems. The formulation allows for simulation of system response due to blade loss, distributed unbalance, base shock, maneuver loads, and specified fixed frame forces. The motion of each rotating component of the system is described by superposing constraint modes associated with boundary coordinates and constrained precessional modes associated with internal coordinates. The precessional modes are truncated for each component and the reduced component equations are assembled with the nonlinear supports and interconnections to form a set of nonlinear system equations of reduced order. These equations are then numerically integrated to obtain the system response. A computer program, which is presently restricted to single shaft systems has been written and results are presented for transient system response associated with blade loss dynamics, with squeeze film dampers, and with interference rubs.

Nonlinear Analysis of Rotor-Bearing Systems Using Component Mode Synthesis

1982 ◽  
Author(s):  
H. D. Nelson ◽  
W. L. Meacham ◽  
D. P. Fleming ◽  
A. F. Kascak
Keyword(s):  
Forced Response ◽  
Component Mode Synthesis ◽  
Squeeze Film ◽  
System Response ◽  
Reduced Order ◽  
Squeeze Film Dampers ◽  
Rotor Bearing ◽  
System Equations ◽  
Transient System ◽  
Blade Loss

The method of component mode synthesis is developed to determine the forced response of nonlinear, multishaft, rotor-bearing systems. The formulation allows for simulation of system response due to blade loss, distributed unbalance, base shock, maneuver loads, and specified fixed frame forces. The motion of each rotating component of the system is described by superposing constraint modes associated with boundary coordinates and constrained precessional modes associated with internal coordinates. The precessional modes are truncated for each component and the reduced component equations are assembled with the nonlinear supports and interconnections to form a set of nonlinear system equations of reduced order. These equations are then numerically integrated to obtain the system response. A computer program, which is presently restricted to single shaft systems, has been written and results are presented for transient system response associated with blade loss dynamics with squeeze film dampers, and with interference rubs.

scholarly journals Analytical and Experimental Investigation of the Stability of the Rotor-Bearing System of a New Small Turbocharger

1987 ◽  
Author(s):  
H. R. Born
Keyword(s):  
Experimental Investigation ◽  
Dynamic Stability ◽  
Squeeze Film ◽  
Test Results ◽  
Flow Capacity ◽  
Squeeze Film Dampers ◽  
Rotor Bearing ◽  
The Stability ◽  
Turbine Design ◽  
Bearing System

This paper presents an overview of the development of a reliable bearing system for a new line of small turbochargers where the bearing system has to be compatible with a new compressor and turbine design. The first part demonstrates how the increased weight of the turbine, due to a 40 % increase in flow capacity, influences the dynamic stability of the rotor-bearing system. The second part shows how stability can be improved by optimizing important floating ring parameters and by applying different bearing designs, such as profiled bore bearings supported on squeeze film dampers. Test results and stability analyses are included as well as the criteria which led to the decision to choose a squeeze film backed symmetrical 3-lobe bearing for this new turbocharger design.

scholarly journals Imbalance Response of a Test Rotor Supported on Squeeze Film Dampers

1998 ◽  
Vol 120 (2) ◽  
pp. 397-404 ◽  
Author(s):  
L. San Andre´s ◽  
D. Lubell
Keyword(s):  
Chaotic Behavior ◽  
Nonlinear Behavior ◽  
Theoretical Models ◽  
Forced Response ◽  
Analytical Models ◽  
Squeeze Film ◽  
Test Rig ◽  
Critical Speeds ◽  
Highly Nonlinear ◽  
Squeeze Film Dampers

Squeeze film dampers (SFDs) provide vibration attenuation and structural isolation to aircraft gas turbine engines which must be able to tolerate larger imbalances while operating above one or more critical speeds. Rotor-bearing-SFD systems are regarded in theory as highly nonlinear, showing jump phenomena and even chaotic behavior for sufficiently large levels of rotor imbalance. Yet, few experimental results of practical value have verified the analytical predictions. A test rig for measurement of the dynamic forced response of a three-disk rotor (45 kg) supported on two cylindrical SFDs is described. The major objective is to provide a reliable data base to validate and enhance SFD design practice and to allow a direct comparison with analytical models. The open-ends SFD are supported by four-bar centering structures, each with a stiffness of 3.5 MN/m. Measured synchronous responses to 9000 rpm due to various imbalances show the rotor-SFD system to be well damped with amplification factors between 1.6 and 2.1 while traversing cylindrical and conical modes critical speeds. The rotor amplitudes of motion are found to be proportional to the imbalances for the first mode of vibration, and the damping coefficients extracted compare reasonably well to predictions based on the full-film, open-ends SFD. Tight lip (elastomeric) seals contribute greatly to the overall damping of the test rig. Measured dynamic pressures at the squeeze film lands are well above ambient values with no indication of lubricant dynamic cavitation as simple theoretical models dictate. The measurements show absence of nonlinear behavior of the rotor-SFD apparatus for the range of imbalances tested.

Theoretical and Experimental Studies on Squeeze Film Stabilizers for Flexible Rotor-Bearing Systems Using Newtonian and Viscoelastic Lubricants

1990 ◽  
Vol 112 (4) ◽  
pp. 473-482 ◽  
Author(s):  
B. Halder ◽  
A. Mukherjee ◽  
R. Karmakar
Keyword(s):  
High Speed ◽  
Experimental Studies ◽  
Squeeze Film ◽  
Experimental Investigations ◽  
Flexible Rotor ◽  
Stability Range ◽  
High Speeds ◽  
Flexible Rotors ◽  
Rotor Bearing

A combination of a squeeze film damper and a plane journal bearing is studied as a stabilizing scheme. The damper is made to play the role of a stabilizer to postpone the instability threshold speeds of flexible rotors. Both Newtonian and viscoelastic fluids are used in the rotor-bearing system. Dynamics of the system is theoretically analyzed using bond graphs. Analysis reveals that the use of a Newtonian fluid in the stabilizer largely improves the high speed stability range. However, viscoelastic stabilizing fluid has a detrimental effect on highly flexible rotors. Experimental investigations, conducted on a flexible rotor (natural frequency, 30 Hz), confirm the theoretical findings. In addition, experiments indicate that though the use of viscoelastic stabilizing fluids leads to instability in flexible rotors, the growth of large amplitude whirl is postponed to very high speeds.

scholarly journals The Effect of Squeeze Film Damper Parameters on the Unbalance Response and Stability of a Flexible Rotor

1996 ◽  
Author(s):  
F. Chu ◽  
R. Holmes
Keyword(s):  
Research Work ◽  
Stability Control ◽  
Squeeze Film ◽  
Flexible Rotor ◽  
Squeeze Film Damper ◽  
Significant Movement ◽  
Squeeze Film Dampers ◽  
Bearing Assembly ◽  
Static Eccentricity ◽  
Points Of View

There has been much research work carried out on various aspects of individual squeeze-film dampers (SFDs) but very little on the interplay between a damper and the rotating assembly of which it forms a part. In this paper, a flexible rotor-bearing assembly in a configuration, typical of a small centrifugal pump and incorporating an SFD is investigated theoretically and experimentally from the points of view of forced vibration control and stability control. It is found that change in rotor unbalance, SFD static eccentricity ratio and SFD supply pressure can cause significant movement of system resonances and vibration resulting from excessive damping. The provision of an SFD also delays the onset of instability and because of its nonlinearity, the SFD contributes more damping than can a linear damper when the vibration amplitude becomes large as instability develops. It is shown that this instability is curbed at some limit cycle, whose frequency is a system natural frequency.

Sign in / Sign up

Export Citation Format

Share Document