Improvement of Seismic Performance of Ordinary Reinforced Partially Grouted Concrete Masonry Shear Walls

2021 ◽  
Author(s):  
Mohammad Bolhassani
Keyword(s):  
Seismic Performance ◽  
Shear Walls ◽  
Concrete Masonry

Seismic Performance of Cantilever-Reinforced Concrete Masonry Shear Walls

2014 ◽  
Vol 140 (9) ◽  
pp. 04014051 ◽  
Author(s):  
Farhad Ahmadi ◽  
Jaime Hernandez ◽  
Jacob Sherman ◽  
Christina Kapoi ◽  
Richard E. Klingner ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Seismic Performance ◽  
Shear Walls ◽  
Concrete Masonry

scholarly journals Experimental Investigation into the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls with Vertical Joint Connections

2021 ◽  
Vol 11 (10) ◽  
pp. 4421
Author(s):  
Zhiming Zhang ◽  
Fenglai Wang
Keyword(s):  
Seismic Performance ◽  
Cross Sections ◽  
Shear Walls ◽  
Construction Method ◽  
Shear Capacity ◽  
Initial Stiffness ◽  
Equivalent Viscous Damping ◽  
Displacement Ductility ◽  
Reinforced Masonry ◽  
Cracking Performance

In this study, four single-story reinforced masonry shear walls (RMSWs) (two prefabricated and two cast-in-place) under reversed cyclic loading were tested to evaluate their seismic performance. The aim of the study was to evaluate the shear behavior of RMSWs with flanges at the wall ends as well as the effect of construction method. The test results showed that all specimens had a similar failure mode with diagonal cracking. However, the crack distribution was strongly influenced by the construction method. The lateral capacity of the prefabricated walls was 12% and 27% higher than that of the corresponding cast-in-place walls with respect to the rectangular and T-shaped cross sections. The prefabricated walls showed better post-cracking performance than did the cast-in-place wall. The secant stiffness of all the walls decreased rapidly to approximately 63% of the initial stiffness when the first major diagonal crack was observed. The idealized equivalent elastic-plastic system showed that the prefabricated walls had a greater displacement ductility of 3.2–4.8 than that of the cast-in-place walls with a displacement ductility value of 2.3–2.7. This proved that the vertical joints in prefabricated RMSWs enhanced the seismic performance of walls in shear capacity and ductility. In addition, the equivalent viscous damping of the specimens ranged from 0.13 to 0.26 for prefabricated and cast-in-place walls, respectively.

Study on Seismic Behavior of the L-Shape Steel Reinforced Concrete Short-Pier Shear Wall with Different Concrete Strength

2013 ◽  
Vol 353-356 ◽  
pp. 1990-1999
Author(s):  
Yi Sheng Su ◽  
Er Cong Meng ◽  
Zu Lin Xiao ◽  
Yun Dong Pi ◽  
Yi Bin Yang
Keyword(s):  
Numerical Simulation ◽  
Reinforced Concrete ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Concrete Strength ◽  
Shear Walls ◽  
Shear Wall ◽  
Simulation Software ◽  
Steel Reinforced Concrete ◽  
Shrinkage Effect

In order to discuss the effect of different concrete strength on the seismic behavior of the L-shape steel reinforced concrete (SRC) short-pier shear wall , this article analyze three L-shape steel reinforced concrete short-pier shear walls of different concrete strength with the numerical simulation software ABAQUS, revealing the effects of concrete strength on the walls seismic behavior. The results of the study show that the concrete strength obviously influence the seismic performance. With the concrete strength grade rise, the bearing capacity of the shear wall becomes large, the ductility becomes low, the pinch shrinkage effect of the hysteresis loop becomes more obvious.

scholarly journals Steel Plate Cold-Rolled Section Steel Embedded High-Strength Concrete Low-Rise Shear Wall Seismic Performance

2018 ◽  
Vol 2018 ◽  
pp. 1-18
Author(s):  
Min Gan ◽  
Yu Yu ◽  
Liren Li ◽  
Xisheng Lu
Keyword(s):  
Bearing Capacity ◽  
Failure Mode ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
Steel Plate ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Steel Plates ◽  
Strength Concrete

Four test pieces with different steel plate center-to-center distances and reinforcement ratios are subjected to low-cycle repeat quasistatic loading to optimize properties as failure mode, hysteretic curve, skeleton curve, energy dissipation parameters, strength parameters, and seismic performance of high-strength concrete low-rise shear walls. The embedded steel plates are shown to effectively restrict wall crack propagation, enhance the overall steel ratio, and improve the failure mode of the wall while reducing the degree of brittle failure. Under the same conditions, increasing the spacing between the steel plates in the steel plate concrete shear wall can effectively preserve the horizontal bearing capacity of the shear wall under an ultimate load. The embedded steel plates perform better than concealed bracing in delaying stiffness degeneration in the low-rise shear walls, thus safeguarding their long-term bearing capacity. The results presented here may provide a workable basis for shear wall design optimization.

Behavior of fully grouted reinforced concrete masonry shear walls failing in flexure: Analysis

2009 ◽  
Vol 31 (9) ◽  
pp. 2032-2044 ◽  
Author(s):  
Marwan T. Shedid ◽  
Wael W. El-Dakhakhni ◽  
Robert G. Drysdale
Keyword(s):  
Reinforced Concrete ◽  
Shear Walls ◽  
Concrete Masonry
Sign in / Sign up

Export Citation Format

Share Document