scholarly journals Noise Levels and Signals Observed on Submarine Fibers in the Canary Islands Using DAS

2021 ◽  
Author(s):  
Arantza Ugalde ◽  
Carlos Becerril ◽  
Antonio Villaseñor ◽  
César R. Ranero ◽  
María R. Fernández-Ruiz ◽  
...  
Keyword(s):  
Canary Islands ◽  
Fiber Optic ◽  
Noise Analysis ◽  
High Amplitude ◽  
Strain Sensors ◽  
Acoustic Oscillations ◽  
Noise Levels ◽  
Mid Atlantic Ridge ◽  
Distributed Acoustic Sensing ◽  
Teleseismic Events

Abstract In this study, we investigate 70 days of distributed acoustic sensing (DAS) recordings in the Canary Islands using an undersea fiber-optic telecommunication cable that links the islands of Tenerife and Gran Canaria. Two DAS interrogators connected to both ends of the cable turned the fiber into an array of 11,968 strain sensors covering a total length of ∼120 km. We present the details of the experiment, noise analysis, and examples of recorded signals. Seismic ambient noise levels assessment indicates poor local coupling of the cable due to the irregular bathymetry that results in high-amplitude acoustic oscillations in some channels. The DAS array recorded several types of nonseismic (vehicles, surface gravity waves, ships) and seismic signals. Local and regional earthquakes were detected with magnitudes mbLg≥2. Surface waves from teleseismic events at a distance of ∼3000 km were also identified in the strain recordings. Here, we report the first observations with DAS of hydroacoustic T waves generated by oceanic earthquakes located at the Central Mid-Atlantic Ridge and the Cape St. Vincent region. Events had magnitudes from Mw 4.2 to 6.9, and the hydroacoustic waves were recorded at epicentral distances from 780 to 3400 km. Our findings show that submarine fiber-optic cables can effectively be used to assess the seismic activity in remote oceanic areas.

Capturing Glacier-Wide Cryoseismicity With Distributed Acoustic Sensing

2021 ◽  
Author(s):  
Fabian Walter ◽  
Patrick Paitz ◽  
Andreas Fichtner ◽  
Pascal Edme ◽  
Wojciech Gajek ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Flow Line ◽  
Ground Deformation ◽  
Sensor Coverage ◽  
Mountain Glacier ◽  
Acoustic Sensing ◽  
Alpine Glacier ◽  
Glacier Ice ◽  
Distributed Acoustic Sensing ◽  
Ice Sheet Dynamics

<p>Over the past 1-2 decades, seismological measurements have provided new and unique insights into glacier and ice sheet dynamics. At the same time, sensor coverage is typically limited in harsh glacial environments with littile or no access. Turning kilometer-long fiber optic cables placed on the Earth’s surface into thousands of seismic sensors, Distributed Acoustic Sensing (DAS) may overcome the limitation of sensor coverage in the cryosphere.</p><p>First DAS applications on the Greenland and Antarctic ice sheets and on Alpine glacier ice have highlighted the technique’s superiority. Signals of natural and man-made seismic sources can be resolved with an unrivaled level of detail. This offers glaciologists new perspectives to interpret their seismograms in terms of ice structure, basal boundary conditions and source locations. However, previous studies employed only relatively small network scales with a point-like borehole deployment or < 1 km cable aperture at the ice surface.</p><p>Here we present a DAS installation, which aims to cover the majority of an Alpine glacier catchment: For one month in summer 2020 we deployed a 9 km long fiber optic cable on Rhonegletscher, Switzerland, and gathered continuous DAS data. The cable followed the glacier’s central flow line starting in the lowest kilometer of the ablation zone and extending well into the accumulation area. Even for a relatively small mountain glacier such as Rhonegletscher, cable deployment was a considerable logistical challenge. However, initial data analysis illustrates the benefit compared to conventional cryoseismological instrumentation: DAS measurements capture ground deformation over many octaves, including typical high-frequency englacial sources (10s to 100s of Hz) related to crevasse formation and basal sliding as well as long period signals (10s to 100s of seconds) of ice deformation. Depending on the presence of a snow cover, DAS records contain strong environmental noise (wind, meltwater flow, precipitation) and thus exhibit lower signal-to-noise ratios compared to conventional on-ice seismic installations. This is nevertheless outweighed by the advantage of monitoring ground unrest and ice deformation of nearly an entire glacier. We present a first compilation of signal and noise records and discuss future directions to leverage DAS data sets in glaciological research.</p><p> </p><p> </p><p> </p>

Seismic Observations of Four Thunderstorms Using an Underground Fiber-Optic Array

2021 ◽  
Author(s):  
Samuel Hone ◽  
Tieyuan Zhu
Keyword(s):  
Fiber Optic ◽  
Seismic Velocity ◽  
Ground Surface ◽  
State College ◽  
Full Waveform ◽  
Penn State ◽  
Distributed Acoustic Sensing ◽  
Back Azimuth ◽  
Optic Array ◽  
The Waves

Abstract Thunderstorms are a common atmospheric phenomenon that cause abundant acoustic disturbances, which can interact with the ground surface, creating a link between atmospheric and solid Earth processes. This article reports seismological observations of four thunderstorms through the spring and summer of 2019, as recorded by the distributed acoustic sensing fiber-optic array (4.9 km) on the Penn State campus in State College, Pennsylvania. With a dense sensor array in the local region, we are able to construct the seismic full waveform response of the thunderstorm events (hereafter referred to as thunderquakes) and track the wave propagation across the array. We use a time-domain grid search to obtain the back azimuth and slowness of the waves, and a modified Geiger’s method to pinpoint source locations of the thunderquakes. Correlated with the time of the recorded signal, this data allows reconstruction of thunderstorm movement as well as offering measurements of the seismic velocity.

scholarly journals Background noise analysis in urban airport surroundings of Brazilian cities, Congonhas Airport, São Paulo

2016 ◽  
Vol 50 (0) ◽  
Author(s):  
Fabio Scatolini ◽  
Cláudio Jorge Pinto Alves
Keyword(s):  
Traffic Control ◽  
Background Noise ◽  
Noise Analysis ◽  
Exposure Level ◽  
Noise Levels ◽  
Sound Exposure ◽  
Operational Characteristics ◽  
Data Compilation ◽  
Noise Measurements ◽  
Noise Data

ABSTRACT OBJECTIVE To perform a quantitative analysis of the background noise at Congonhas Airport surroundings based on large sampling and measurements with no interruption. METHODS Measuring sites were chosen from 62 and 72 DNL (day-night-level) noise contours, in urban sites compatible with residential use. Fifteen sites were monitored for at least 168 hours without interruption or seven consecutive days. Data compilation was based on cross-reference between noise measurements and air traffic control records, and results were validated by airport meteorological reports. Preliminary diagnoses were established using the standard NBR-13368. Background noise values were calculated based on the Sound Exposure Level (SEL). Statistic parameters were calculated in one-hour intervals. RESULTS Only four of the fifteen sites assessed presented aircraft operations as a clear cause for the noise annoyance. Even so, it is possible to detect background noise levels above regulation limits during periods of low airport activity or when it closes at night. CONCLUSIONS All the sites monitored showed background noise levels above regulation limits between 7:00 and 21:00. In the intervals between 6:00-6:59 and 21:00-22:59 the noise data, when analyzed with the current airport operational characteristics, still allow the development of additional mitigating measures.

Experimental Investigation of Combustion Dynamics in a Turbulent Syngas Combustor

2017 ◽  
Author(s):  
Nikhil Ashokbhai Baraiya ◽  
Baladandayuthapani Nagarajan ◽  
Satynarayanan R. Chakravarthy
Keyword(s):  
High Speed ◽  
Equivalence Ratio ◽  
Bluff Body ◽  
Dynamic Pressure ◽  
Fuel Mixture ◽  
High Amplitude ◽  
Acoustic Oscillations ◽  
Combustion Dynamics ◽  
Dynamic Pressure Measurement ◽  
Body Location

In the present work, the proportion of carbon monoxide to hydrogen is widely varied to simulate different compositions of synthesis gas and the potential of the fuel mixture to excite combustion oscillations in a laboratory-scale turbulent bluff body combustor is investigated. The effect of parameters such as the bluff body location and equivalence ratio on the self-excited acoustic oscillations of the combustor is studied. The flame oscillations are mapped by means of simultaneous high-speed CH* and OH* chemiluminescence imaging along with dynamic pressure measurement. Mode shifts are observed as the bluff body location or the air flow Reynolds number/overall equivalence ratio are varied for different fuel compositions. It is observed that the fuel mixtures that are hydrogen-rich excite high amplitude pressure oscillations as compared to other fuel composition cases. Higher H2 content in the mixture is also capable of exciting significantly higher natural acoustic modes of the combustor so long as CO is present, but not without the latter. The interchangeability factor Wobbe Index is not entirely sufficient to understand the unsteady flame response to the chemical composition.

scholarly journals Application of a three-step approach for prediction of combustion instabilities in industrial gas turbine burners

2017 ◽  
Vol 1 ◽  
pp. JCW78T
Author(s):  
Dmytro Iurashev ◽  
Giovanni Campa ◽  
Vyacheslav V. Anisimov ◽  
Ezio Cosatto ◽  
Luca Rofi ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Time Lag ◽  
High Amplitude ◽  
Combustion Regime ◽  
Industrial Test ◽  
Distributed Model ◽  
Combustion Instabilities ◽  
Acoustic Oscillations ◽  
Analytical Time

Abstract Recently, because of environmental regulations, gas turbine manufacturers are restricted to produce machines that work in the lean combustion regime. Gas turbines operating in this regime are prone to combustion-driven acoustic oscillations referred as combustion instabilities. These oscillations could have such high amplitude that they can damage gas turbine hardware. In this study, the three-step approach for combustion instabilities prediction is applied to an industrial test rig. As the first step, the flame transfer function (FTF) of the burner is obtained performing unsteady computational fluid dynamics (CFD) simulations. As the second step, the obtained FTF is approximated with an analytical time-lag-distributed model. The third step is the time-domain simulations using a network model. The obtained results are compared against the experimental data. The obtained results show a good agreement with the experimental ones and the developed approach is able to predict thermoacoustic instabilities in gas turbines combustion chambers.

scholarly journals Investigation of the Effects of Surrounding Media on the Distributed Acoustic Sensing of Helically-Wound Fiber-Optic Cable with Application to the New Afton Deposit, British Columbia

2020 ◽  
Author(s):  
Sepidehalsadat Hendi ◽  
Mostafa Gorjian ◽  
Gilles Bellefleur ◽  
Christopher D. Hawkes ◽  
Don White
Keyword(s):  
British Columbia ◽  
Numerical Modeling ◽  
Analytical Model ◽  
Field Data ◽  
Fiber Optic ◽  
Incident Angle ◽  
Acoustic Sensing ◽  
Distributed Acoustic Sensing ◽  
Straight Fiber

Abstract. Fiber optic sensing technology has recently become popular for oil and gas, mining, geotechnical engineering, and hydrogeology applications. With a successful track record in many applications, distributed acoustic sensing using straight fiber optic cables has become a method of choice for seismic studies. However, distributed acoustic sensing using straight fiber optic cables is not able to detect off-axial strain, hence a helically wound cable design was introduced to overcome this limitation. The helically wound cable field data in New Afton deposit showed that the quality of the data is tightly dependent on the incident angle (the angle between the ray and normal vector of the surface) and surrounding media. We introduce a new analytical two-dimensional approach to determine the dynamic strain of a helically wound cable in terms of incident angle in response to elastic plane waves propagating through multilayered media. The method can be used to quickly and efficiently assess the effects of various materials surrounding a helically wound cable. Results from the proposed analytical model are compared with results from numerical modeling obtained with COMSOL Multiphysics, for scenarios corresponding to a real installation of helically wound cable deployed underground at the New Afton mine in British Columbia, Canada. Results from the analytical model are consistent with numerical modeling results. Our modeling results demonstrate the effects of cement quality, and casing installment on the quality of the helically-wound cable response. Numerical modeling results and field data suggest that, even if reasonably effective coupling achieved, the soft nature of the rocks in these intervals would result in low fiber strains for the HWC. The proposed numerical modeling workflow would be applied for more complicated scenarios (e.g., non-linear material constitutive behaviour, and the effects of pore fluids). The results of this paper can be used as a guideline for analyzing the effect of surrounding media and incident angle on the response of helically wound cable, optimizing the installation of helically wound cable in various conditions, and to validate boundary conditions of 3-D numerical model built for analyzing complex scenarios.

Sign in / Sign up

Export Citation Format

Share Document