scholarly journals STUDY OF AUXILIARY GAS PRESSURE ON LASER CUTTING TECHNOLOGY

2017 ◽  
Vol 3 ◽  
pp. 163
Author(s):  
Lyubomir Lazov ◽  
Hristina Deneva ◽  
Erika Teirumnieka
Keyword(s):  
Laser Power ◽  
Laser Cutting ◽  
Sheet Steel ◽  
Cutting Speed ◽  
Major Effect ◽  
Gas Pressure ◽  
Experimental Results ◽  
Focus Position ◽  
Angle Deviation ◽  
Basic Parameters

Two types of electrical sheet steel M250-35A and M530-50A were used to cut by melting with a TruLaser 1030 technological system. It was observed that pressure of auxiliary gas had a major effect on kerf width b and cut angle deviation α. Nitrogen as an assisted gas has been taken. The basic parameters as laser power, cutting speed, focus position were constantly supported and the pressure was changed from 4 bar to 20 bar by step 2 bar. As well as the experimental results of gas pressure on entrance and exit kerf widths, have been analyzed and discussed in this study.

EXPERIMENTAL EVALUATION OF CO2 LASER CUTTING QUALITY OF UHSS USING OXYGEN AS AN ASSISTED GAS

2016 ◽  
Vol 78 (7) ◽  
Author(s):  
Abdul Fattah Mohamad Tahir ◽  
Ahmad Razelan Rashid
Keyword(s):  
Co2 Laser ◽  
High Strength Steel ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
High Strength ◽  
Gas Pressure ◽  
Kerf Width ◽  
Boron Steel ◽  
Major Factors

Development of new material known as Ultra High Strength Steel (UHSS) able to improve the vehicle mass thus reflecting better fuel consumption. Transformation into high strength steel has been a significant drawback in trimming the UHSS into its final shape thus laser cutting process appeared to be the solution. This study emphasizes the relationship between Carbon Dioxide (CO2) laser cutting input parameters on 22MnB5 boron steel focusing on the kerf width formation and Heat Affected Zone (HAZ). Experimental research with variation of laser power, cutting speed and assisted gas pressure were executed to evaluate the responses. Metrological and metallographic evaluation of the responses were made on the outputs that are the kerf width formation and HAZ.  Positive correlation for power and negative interaction for cutting speed were found as the major factors on formation of the kerf. For the HAZ formation, thicker HAZ were formed as bigger laser power were applied to the material. Cutting speed and gas pressure does not greatly influence the HAZ formation for 22MnB5 boron steel.

scholarly journals Analysis of the heat affected zone in CO2 laser cutting of stainless steel

2012 ◽  
Vol 16 (suppl. 2) ◽  
pp. 363-373 ◽  
Author(s):  
Milos Madic ◽  
Miroslav Radovanovic
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Heat Affected Zone ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Data Sets ◽  
Focus Position ◽  
Artificial Neural

This paper presents an investigation into the effect of the laser cutting parameters on the heat affected zone in CO2 laser cutting of AISI 304 stainless steel. The mathematical model for the heat affected zone was expressed as a function of the laser cutting parameters such as the laser power, cutting speed, assist gas pressure and focus position using the artificial neural network. To obtain experimental database for the artificial neural network training, laser cutting experiment was planned as per Taguchi?s L27 orthogonal array with three levels for each of the cutting parameter. Using the 27 experimental data sets, the artificial neural network was trained with gradient descent with momentum algorithm and the average absolute percentage error was 2.33%. The testing accuracy was then verified with 6 extra experimental data sets and the average predicting error was 6.46%. Statistically assessed as adequate, the artificial neural network model was then used to investigate the effect of the laser cutting parameters on the heat affected zone. To analyze the main and interaction effect of the laser cutting parameters on the heat affected zone, 2-D and 3-D plots were generated. The analysis revealed that the cutting speed had maximum influence on the heat affected zone followed by the laser power, focus position and assist gas pressure. Finally, using the Monte Carlo method the optimal laser cutting parameter values that minimize the heat affected zone were identified.

EXPERIMENTAL STUDY ON THE CO2 LASER CUTTING OF NOVEL POLYAMIDE 6/FLUOROELASTOMER THERMOPLASTIC ELASTOMERIC BLENDS

2015 ◽  
Vol 88 (1) ◽  
pp. 125-137 ◽  
Author(s):  
Shib Shankar Banerjee ◽  
Anil K. Bhowmick
Keyword(s):  
Low Power ◽  
Co2 Laser ◽  
Process Parameters ◽  
Laser Power ◽  
Laser Cutting ◽  
Manufacturing Industry ◽  
Cutting Speed ◽  
Polyamide 6 ◽  
Thermoplastic Elastomers ◽  
Dynamic Vulcanization

ABSTRACT The application of the low-power CO2 laser-cutting process to fluoroelastomer (FKM), polyamide 6 (PA6), PA6/FKM thermoplastic elastomers (TPEs), and their thermoplastic vulcanizate (TPV) is reported. The main laser process parameters studied were laser power, cutting speed, and material thickness. The value of the top and bottom widths of the slit that were formed during laser cutting (kerf width), melted transverse area, and melted volume per unit time were measured and analyzed. Interestingly, TPE showed a smaller melted area and melted volume per unit time when compared with those values with PA6. Dynamic vulcanization further decreased these values. For example, the melted areas of PA6 and TPE were 510 × 10−3 mm2 and 305 × 10−3 mm2, respectively, which reduced to 238 × 10−3 mm2 for TPV at 40 W laser power. FKM showed the lowest value (melted area of 180 × 10−3 mm2). In addition, the output quality of the cut surface was examined by measuring the root mean square (RMS) roughness of the cut edges and heat-affected zone (HAZ). The obtained results indicated that the dimension of the HAZ and RMS roughness largely decreased in TPE when compared with PA6. For example, the HAZ of PA6 was 700 μm, which decreased to 230 μm for TPE at 40 W laser power. On the other hand, HAZ was nonexistent for FKM. Infrared spectroscopic analysis showed that there was no structural change of TPE or pristine polymers after applying the low-power CO2 laser on the surface of materials. CO2 laser cutting will be a new technique in this industry, and this analysis will assist the manufacturing industry to choose a suitable laser system with exhaustive information of process parameters for cutting or machining of rubber, TPEs, and TPVs.

Analysis of Roughness and Heat Affected Zone of Steel Plates Obtained by Laser Cutting

2014 ◽  
Vol 974 ◽  
pp. 169-173 ◽  
Author(s):  
Imed Miraoui ◽  
Mohamed Boujelbene ◽  
Emin Bayraktar
Keyword(s):  
Surface Roughness ◽  
Laser Beam ◽  
Heat Affected Zone ◽  
Laser Power ◽  
Laser Cutting ◽  
Major Effect ◽  
Steel Plates ◽  
Beam Diameter ◽  
Laser Beam Diameter ◽  
Cut Surface

In the present study, high-power CO2 laser cutting of steel plates has been investigated and the effect of the input laser cutting parameters on the cut surface quality is analyzed. The average roughness of the cut surface of the specimens, produced by different laser beam diameter and laser power, were measured by using roughness tester. The scanning electron microscopy SEM is used to record possible metallurgical alterations on the cut edge. The aim of this work is to investigate the effect of laser beam diameter and laser power on the cut surface roughness and on the heat affected zone width HAZ of steel plates obtained by CO2 laser cutting. An overall optimization was applied to find out the optimal cutting setting that would improve the cut surface quality. It was found that laser beam diameter has a negligible effect on surface roughness but laser power had major effect on roughness. The cut surface roughness decreases as laser power increases. Improved surface roughness can be obtained at higher laser power. Also, laser beam diameter and laser power had major effect on HAZ width. It increases as laser power increases.

Analysis of process efficiency in laser fusion cutting and some single- and multi-objective optimization aspects

2021 ◽  
pp. 095440892110627
Author(s):  
Miloš Madić ◽  
Mohamed H Gadallah ◽  
Dušan Petković
Keyword(s):  
Laser Power ◽  
Laser Cutting ◽  
Optimization Problem ◽  
Removal Rate ◽  
Cutting Speed ◽  
Process Efficiency ◽  
Laser Fusion ◽  
Cut Quality ◽  
Dross Formation ◽  
Laser Fusion Cutting

For an efficient use of laser cutting technology, it is of great importance to analyze the impact of process parameters on different performance indicators, such as cut quality criteria, productivity criteria, costs as well as environmental performance criteria (energy and resource efficiency). Having this in mind, this study presents the experimental results of CO2 laser fusion cutting of AISI 304 stainless steel using nitrogen, with the aim of developing a semi-empirical mathematical model for the estimation of process efficiency as an important indicator of the achievable energy transfer efficiency in the cutting process. The model was developed by relating the theoretical power needed to melt the volume per unit time and used laser power, where the change of kerf width was modeled using an empirical power model in terms of laser cutting parameters such as laser power, cutting speed, and focus position. The obtained results indicated the dominant effect of the focus position on the change in process efficiency, followed by the cutting speed and laser power. In addition, in order to maximize process efficiency and simultaneously ensure high cut quality without dross formation, a laser cutting optimization problem with constraints was formulated and solved. Also, a multi-objective optimization problem aimed at simultaneous optimization of process efficiency and material removal rate was formulated and solved, where the determined set of Pareto non-dominated solutions was analyzed by using the entropy method and multi-criteria decision analysis method, that is, the Technique for Order of Preference by Similarity to Ideal Solution. The optimization results revealed that in order to enhance process efficiency and material removal rate, while ensuring high cut quality without dross formation, focusing the laser beam deep into the bulk of material is needed with particular trade-offs between laser power and cutting speed levels at high pressure levels of nitrogen.

scholarly journals Cutting Properties of Austenitic Stainless Steel by Using Laser Cutting Process without Assist Gas

2012 ◽  
Vol 2012 ◽  
pp. 1-8
Author(s):  
Hitoshi Ozaki ◽  
Yosuke Koike ◽  
Hiroshi Kawakami ◽  
Jippei Suzuki
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Molten Metal ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Process ◽  
Metallic Materials ◽  
Bottom Side ◽  
Gas Nozzle

Recently, laser cutting is used in many industries. Generally, in laser cutting of metallic materials, suitable assist gas and its nozzle are needed to remove the molten metal. However, because of the gas nozzle should be set closer to the surface of a workpiece, existence of the nozzle seems to prevent laser cutting from being used flexible. Therefore, the new cutting process, Assist Gas Free laser cutting or AGF laser cutting, has been developed. In this process, the pressure at the bottom side of a workpiece is reduced by a vacuum pump, and the molten metal can be removed by the air flow caused by the pressure difference between both sides of the specimen. In this study, cutting properties of austenitic stainless steel by using AGF laser cutting with 2 kW CO2 laser were investigated. Laser power and cutting speed were varied in order to study the effect of these parameters on cutting properties. As a result, austenitic stainless steel could be cut with dross-free by AGF laser cutting. When laser power was 2.0 kW, cutting speed could be increased up to 100 mm/s, and kerf width at specimen surface was 0.28 mm.

A STUDY ON THE SURFACE QUALITIES OF FOUR POLYMER SUBSTRATE MICROCHANNELS USING CO2 LASER FOR MICROFLUIDIC CHIP

2019 ◽  
Vol 26 (03) ◽  
pp. 1850160
Author(s):  
ZENGLIANG HU ◽  
XUEYE CHEN ◽  
YI REN
Keyword(s):  
Polyethylene Terephthalate ◽  
Polymethyl Methacrylate ◽  
Microfluidic Chip ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Processing Parameters ◽  
Polymer Substrate ◽  
Laser Machine ◽  
Polymer Substrates

The paper demonstrates four different polymer substrate microchannels are fabricated by CO2 laser machine. The four different polymer substrates are Polymethyl-methacrylate (PMMA), Polycarbonate (PC), Polystyrene (PS) and Polyethylene Terephthalate (PET), respectively. A number of microchannels are obtained and all roughness is measured. The four different polymer substrate microchannels are processed with different processing parameters. Laser power is set from 4[Formula: see text]W to 32[Formula: see text]W and laser cutting speed is set from 5[Formula: see text]mm/s to 30[Formula: see text]mm/s. The results show the roughness of PS substrate microchannel is lower than that of other three polymer substrate microchannels at the same parameters. When laser power is below 4[Formula: see text]W, the roughness of four polymer substrates are similar. The roughness of different polymer substrate microchannels decreases with the increase of laser power. The roughness of different polymer substrate microchannels also happens to change with increase of laser cutting speed.

Laser Cutting Quality of the Ceramic Slabs

2006 ◽  
Vol 505-507 ◽  
pp. 847-852 ◽  
Author(s):  
Xu Yue Wang ◽  
Wen Ji Xu ◽  
Ren Ke Kang ◽  
Yi De Liang
Keyword(s):  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Incident Laser Power ◽  
Focal Position ◽  
Geometrical Features ◽  
The Relationship ◽  
Cutting System

An experimental analysis is presented which investigates the relationship between cutting parameters and the volume of material removal as well as its cutting quality on a Nd:YAG laser cutting system. The parameters that varied on two testing thickness during cutting include cutting speed, incident laser power and focal position in a continuous through cut. Various trends of the kerf geometrical features in terms of the varying process parameters are analyzed and shown to be reasonable. Discussions are also given on kerf geometry control in situations with cutting parameters. It shows that the effects of varying parameters such as cutting speed, laser power and focal position on cutting kerf width, surface roughness, and striation that have provided a deeper understanding of the laser machining.

Applications of Optical Path Length Compensation Technology for High Power CO2 Laser Cutting Process

2014 ◽  
Vol 939 ◽  
pp. 177-185
Author(s):  
Zhao Chi Chen ◽  
Liang Ju Pan
Keyword(s):  
Cross Section ◽  
Laser Cutting ◽  
Path Length ◽  
Cutting Speed ◽  
Optical Path Length ◽  
Spot Size ◽  
Optical Path ◽  
Cutting Process ◽  
Focus Position ◽  
The Cross

High powerCO2(Carbon Dioxide,CO2) laser cutting process not only attention to the type of material selected, the focus position of the laser beam and spot size (beam size) also plays an important role. In this paper, metal materials cutting through the wavelength of 10.6μm,CO2 laser with the optical path length compensation techniquewith output power 4000W. We compare different focus position and spot size for processing quality to discussing the use of a constant optical path length system to maintain the stability of the cross-section of the metal material after laser cutting.Optical path length compensation is used with ABCD Law in metal (steel) laser cutting processing an indispensable technology.Finally, we verify that the cross-section of the optical path length compensation under laser cutting in different processing location, thicknessof 16 mmsteel with laser power 4000W, and cutting speed 0.9 m/minconditions observed area 3*1.5 m2workingstagefor optical path length of 7, 8.5, 10 and 11.5 m,the steel ofcross-section appearance almost identical.

High Quality Fiber Laser Cutting of Electronic Alumina Ceramics

2010 ◽  
Vol 154-155 ◽  
pp. 917-922 ◽  
Author(s):  
Xiao Chuan Chen ◽  
Ling Fei Ji ◽  
Yong Bao ◽  
Yi Jian Jiang
Keyword(s):  
Fiber Laser ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Alumina Ceramics ◽  
High Quality ◽  
Spot Diameter ◽  
Cutting Surface ◽  
Power Threshold

In this paper, high quality cutting of 1 mm dense Al2O3 electronic ceramic processed by a fiber laser with spot diameter of 15 μm was reported. The narrow kerf with 30μm width was obtained with laser power of 100 W. 300 W is the laser power threshold of the kerf enlargement. Under higher laser power, the ceramics can be damage-free cut with higher cutting speed. Striation-free cutting could be achieved at 1000 W laser power with a cutting speed of 350 mm/s. The ratio of cutting speed to laser power for striation-free cutting was determined as 0.35. The black cutting surface was due to the mass tetragonal alumina induced by N2 as assist gas.

Sign in / Sign up

Export Citation Format

Share Document