scholarly journals Application of the Taguchi method to select the optimum cutting parameters for tangential cylindrical grinding of AISI D3 tool steel

2016 ◽  
Vol 50 (1) ◽  
pp. 81-87 ◽  
Author(s):  
Cetin Ozay ◽  
Hasan Ballikaya ◽  
Vedat Savas
Keyword(s):  
Taguchi Method ◽  
Tool Steel ◽  
Cutting Parameters ◽  
Cylindrical Grinding ◽  
Optimum Cutting ◽  
D3 Tool Steel

scholarly journals Determination of Optimum Cutting Parameters in Sawing Process Using Diamond Cutting Disc by Taguchi Method

2015 ◽  
Vol 15 (3) ◽  
pp. 6-16 ◽  
Author(s):  
İsmail UCUN ◽  
Barış GÖKÇE ◽  
M. Said EKEN ◽  
Kubilay ASLANTAŞ ◽  
İ. Sedat BÜYÜKSAĞİŞ ◽  
...  
Keyword(s):  
Taguchi Method ◽  
Cutting Parameters ◽  
Diamond Cutting ◽  
Optimum Cutting ◽  
Sawing Process

Optimization of EDM Parameters in Machining AISI D3 Tool Steel by Grey Relational Analysis

2013 ◽  
Vol 330 ◽  
pp. 747-753
Author(s):  
Othman Belgassim ◽  
Abdurahman Abu-Saada
Keyword(s):  
Taguchi Method ◽  
Tool Steel ◽  
Process Parameters ◽  
Grey Relational Analysis ◽  
Pulse Current ◽  
Machining Process ◽  
Relational Analysis ◽  
Grey Relational ◽  
Pulse On Time ◽  
D3 Tool Steel

This study presents optimization of multiple performance characteristics [material removal rate (MRR), surface roughness (Ra), and overcut (OC)] of hardened AISI D3 tool steel in electrical discharge machining (EDM) using Taguchi method and Grey relational analysis. Machining process parameters selected were pulse current Ip, pulse-on time Ton, pulse-off time Toff and gap voltage Vg . Based on ANOVA, pulse current is found to be the most significant factor affecting EDM process. Optimized process parameters simultaneously leading to a higher MRR, lower Ra, and lower OC are then verified through a confirmation experiment. Validation experiment shows an improved MRR, Ra and OC when Taguchi method and grey relational analysis were used.

Optimization of Cutting Parameters of Multiple Performance Characteristics in End Milling of AlSi/AIN MMC – Taguchi Method and Grey Relational Analysis

2014 ◽  
Vol 68 (4) ◽  
Author(s):  
S. H. Tomadi ◽  
J. A. Ghani ◽  
C. H. Che Haron ◽  
M. S. Kasim ◽  
A. R. Daud
Keyword(s):  
Taguchi Method ◽  
Grey Relational Analysis ◽  
Volume Fraction ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Performance Characteristics ◽  
Depth Of Cut ◽  
Relational Analysis ◽  
Grey Relational

The main objective of this paper is to investigate and optimize the cutting parameters on multiple performance characteristics in end milling of Aluminium Silicon alloy reinforced with Aluminium Nitride (AlSi/AlN MMC) using Taguchi method and Grey relational analysis (GRA). The fabrication of AlSi/AlN MMC was made via stir casting with various volume fraction of particles reinforcement (10%, 15% and 20%). End milling machining was done under dry cutting condition by using two types of cutting tool (uncoated & PVD TiAlN coated carbide). Eighteen experiments (L18) orthogonal array with five factors (type of tool, cutting speed, feed rate, depth of cut, and volume fraction of particles reinforcement) were implemented. The analysis of optimization using GRA concludes that the better results for the combination of lower surface roughness, longer tool life, lower cutting force and higher material removal could be achieved when using uncoated carbide with cutting speed 240m/min, feed 0.4mm/tooth, depth of cut 0.3mm and 15% volume fraction of AlN particles reinforcement. The study confirmed that with a minimum number of experiments, Taguchi method is capable to design the experiments and optimized the cutting parameters for these performance characteristics using GRA for this newly develop material under investigation.

Optimization of Dressing Parameters in Surface Grinding SKD11 Tool Steel by Using Taguchi Method

2020 ◽  
pp. 636-647
Author(s):  
Tran Thi Hong ◽  
Nguyen Thanh Tu ◽  
Nguyen Anh Tuan ◽  
Tran Ngoc Giang ◽  
Nguyen Thi Quoc Dung ◽  
...  
Keyword(s):  
Taguchi Method ◽  
Tool Steel ◽  
Surface Grinding

Surface Quality of Pulsed Laser Cutting of Difficult to Machine Steel

2011 ◽  
Vol 299-300 ◽  
pp. 1016-1019
Author(s):  
Tie Jun Li ◽  
Jing Tang ◽  
Li Jun Yan ◽  
Yang Wang
Keyword(s):  
Surface Quality ◽  
Laser Cutting ◽  
Pulsed Laser ◽  
Cutting Parameters ◽  
Quality Factors ◽  
Good Separation ◽  
Machine Steel ◽  
Optimum Cutting ◽  
Super Alloy

This paper presented the experiments of Nd:YAG pulsed laser cutting of titanium alloy, super-alloy and stainless steel sheet, and investigated the influences of different laser cutting parameters on the surface quality factors focusing surface morphology. In comparison with air-, argon- and nitrogen-assisted laser cutting, argon-assisted laser cutting comes with unaffected surface quality and is suitable for laser cutting with subsequent welding requirement. With analyzing the interaction between pulses overlapping rate and energy, the results show that medium pulse overlapping rate and lower pulse rate helps to improve the surface roughness with pulsed laser cutting. And the results would be beneficial to find optimum cutting parameters for good separation surface.

Sign in / Sign up

Export Citation Format

Share Document