scholarly journals   Percolation in macropores and performance of large time-domain reflectometry sensors

2012 ◽  
Vol 58 (No. 11) ◽  
pp. 503-507 ◽  
Author(s):  
F. Doležal ◽  
S. Matula ◽  
J.M. Moreira Barradas
Keyword(s):  
Time Domain ◽  
Large Time ◽  
Large Diameter ◽  
Soil Heterogeneity ◽  
Time Domain Reflectometry ◽  
Soil Slurry ◽  
Loamy Soil ◽  
Field Calibration ◽  
Native Soil ◽  
And Performance

  The large-diameter time-domain reflectometry soil water sensors placed horizontally in a structured loamy soil are very sensitive to rapid preferential percolation events. Their readings on these occasions rise considerably, often becoming higher than the native soil’s porosity. The effect is caused by gaps between the native soil and the sensors. The geometry of the gaps, even if filled with soil slurry at installation, is not exactly reproducible, which leads to sensor-to-sensor variability of readings. Field calibration in percolation-free periods lead to non-unique trajectories rather than monotonous calibration curves, which can be commented in terms of soil heterogeneity and the dual porosity theory. Data of two typical percolation events are presented. Sensors of this type can be used for detection of preferential flux.  

Fabrication and Evaluation of 3D Packages with Through Hole Via

2006 ◽  
Vol 970 ◽  
Author(s):  
Dong Min Jang ◽  
Kwang Yong Lee ◽  
Chung Hyun Ryu ◽  
Byeong Hoon Cho ◽  
Tae Sung Oh ◽  
...  
Keyword(s):  
Time Domain ◽  
Time Domain Reflectometry ◽  
Model Parameters ◽  
Eye Diagram ◽  
Area Efficiency ◽  
Layer Deposition ◽  
Proposed Model ◽  
Via Holes ◽  
And Performance ◽  
Through Hole

ABSTRACTSystem in package (SiP) is a superb candidate to enhance the area efficiency and performance of electronic packaging. Here, recent work on stacked chip type 3D SiP with vertically interconnected through hole vias are reported. The process includes; formation of 50um-diameter via holes, conformal deposition of SiO2 dielectric layer, deposition of Ta and Cu barrier layers, via filling by Cu electroplating, Cu/Sn bump formation for multi-chip stacking, and finally chip-to-PCB bonding using Sn-3.0Ag-0.5Cu solder and ENIG pad. A prototype 3D SiP stacked up to 10 layers was successfully fabricated.A high frequency electrical model of the through hole via was proposed and the model parameters were extracted from measured S-parameters. The proposed model was verified by TDR/TDT (time domain reflectometry/time domain transmission) and eye-diagram measurement. Contact resistances of Cu via and bump joint were presented.

Time Domain Reflectometry Field Calibration in the Little Washita River Experimental Watershed

2003 ◽  
Vol 67 (1) ◽  
pp. 52-61 ◽  
Author(s):  
Gary C. Heathman ◽  
Patrick J. Starks ◽  
Michael A. Brown
Keyword(s):  
Time Domain ◽  
Time Domain Reflectometry ◽  
Field Calibration

Advanced Non-Destructive Fault Isolation Techniques for PCB Substrates Using Magnetic Current Imaging and Terahertz Time Domain Reflectometry

2018 ◽  
Author(s):  
Daechul Choi ◽  
Yoonseong Kim ◽  
Jongyun Kim ◽  
Han Kim
Keyword(s):  
Time Domain ◽  
Quantum Interference ◽  
Flip Chip ◽  
Imaging System ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Magnetic Current ◽  
Isolation Techniques ◽  
Super Conducting ◽  
Non Destructive

Abstract In this paper, we demonstrate cases for actual short and open failures in FCB (Flip Chip Bonding) substrates by using novel non-destructive techniques, known as SSM (Scanning Super-conducting Quantum Interference Device Microscopy) and Terahertz TDR (Time Domain Reflectometry) which is able to pinpoint failure locations. In addition, the defect location and accuracy is verified by a NIR (Near Infra-red) imaging system which is also one of the commonly used non-destructive failure analysis tools, and good agreement was made.

Super-Conducting Quantum Interference Device Technique: 3-D Localization of a Short within a Flip Chip Assembly

2001 ◽  
Author(s):  
Kendall Scott Wills ◽  
Omar Diaz de Leon ◽  
Kartik Ramanujachar ◽  
Charles P. Todd
Keyword(s):  
Form Factor ◽  
Failure Analysis ◽  
Time Domain ◽  
Quantum Interference ◽  
Flip Chip ◽  
Time Domain Reflectometry ◽  
Interfacial Region ◽  
Precise Localization ◽  
Super Conducting ◽  
Accuracy Of Measurement

Abstract In the current generations of devices the die and its package are closely integrated to achieve desired performance and form factor. As a result, localization of continuity failures to either the die or the package is a challenging step in failure analysis of such devices. Time Domain Reflectometry [1] (TDR) is used to localize continuity failures. However the accuracy of measurement with TDR is inadequate for effective localization of the failsite. Additionally, this technique does not provide direct 3-Dimenstional information about the location of the defect. Super-conducting Quantum Interference Device (SQUID) Microscope is useful in localizing shorts in packages [2]. SQUID microscope can localize defects to within 5um in the X and Y directions and 35um in the Z direction. This accuracy is valuable in precise localization of the failsite within the die, package or the interfacial region in flipchip assemblies.

Failure Analysis of Broken Stitch Bonds in TSSOP Packages Using Scanning Acoustic Microscopy (SAM) and Time Domain Reflectometry (TDR)

2004 ◽  
Author(s):  
Bilal Abd-AlRahman ◽  
Corey Lewis ◽  
Todd Simons
Keyword(s):  
Failure Analysis ◽  
Mechanical Stress ◽  
Time Domain ◽  
Open Circuit ◽  
Time Domain Reflectometry ◽  
Acoustic Microscopy ◽  
Scanning Acoustic Microscopy ◽  
Root Cause ◽  
Analysis Application

Abstract A failure analysis application utilizing scanning acoustic microscopy (SAM) and time domain reflectometry (TDR) for failure analysis has been developed to isolate broken stitch bonds in thin shrink small outline package (TSSOP) devices. Open circuit failures have occurred in this package due to excessive bending of the leads during assembly. The tools and their specific application to this technique as well as the limitations of C-SAM, TDR and radiographic analyses are discussed. By coupling C-SAM and TDR, a failure analyst can confidently determine whether the cause of an open circuit in a TSSOP package is located at the stitch bond. The root cause of the failure was determined to be abnormal mechanical stress placed on the pins during the lead forming operation. While C-SAM and TDR had proven useful in the analysis of TSSOP packages, it can potentially be expanded to other wire-bonded packages.

Time Domain Reflectometry Technique for Failure Analysis

2004 ◽  
Author(s):  
Teoh King Long ◽  
Ko Yin Fern
Keyword(s):  
Failure Analysis ◽  
Time Domain ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Reference Plane ◽  
First Case ◽  
Main Emphasis ◽  
Plastic Ball ◽  
Solder Balls ◽  
Non Destructive

Abstract In time domain reflectometry (TDR), the main emphasis lies on the reflected waveform. Poor probing contact is one of the common problems in getting an accurate waveform. TDR probe normalization is essential before measuring any TDR waveforms. The advantages of normalization include removal of test setup errors in the original test pulse and the establishment of a measurement reference plane. This article presents two case histories. The first case is about a Plastic Ball Grid Array package consisting of 352 solder balls where the open failure mode was encountered at various terminals after reliability assessment. In the second, a three-digit display LED suspected of an electrical short failure was analyzed using TDR as a fault isolation tool. TDR has been successfully used to perform non-destructive fault isolation in assisting the routine failure analysis of open and short failure. It is shown to be accurate and reduces the time needed to identify fault locations.

Advanced Fault Isolation Technique Using Electro-Optical Terahertz Pulse Reflectometry (EOTPR) for 2D and 2.5D Flip-Chip Package

2012 ◽  
Author(s):  
Lihong Cao ◽  
Manasa Venkata ◽  
Meng Yeow Tay ◽  
Wen Qiu ◽  
J. Alton ◽  
...  
Keyword(s):  
Time Domain ◽  
Flip Chip ◽  
Time Domain Reflectometry ◽  
Fault Isolation ◽  
Experimental Results ◽  
Terahertz Pulse ◽  
Isolation And Identification ◽  
Isolation Technique ◽  
Non Destructive

Abstract Electro-optical terahertz pulse reflectometry (EOTPR) was introduced last year to isolate faults in advanced IC packages. The EOTPR system provides 10μm accuracy that can be used to non-destructively localize a package-level failure. In this paper, an EOTPR system is used for non-destructive fault isolation and identification for both 2D and 2.5D with TSV structure of flip-chip packages. The experimental results demonstrate higher accuracy of the EOTPR system in determining the distance to defect compared to the traditional time-domain reflectometry (TDR) systems.

Sign in / Sign up

Export Citation Format

Share Document