scholarly journals Engine performance and exhaust emission characteristics of paraffinic diesel fuel in a model diesel engine 

2018 ◽  
Vol 64 (No. 2) ◽  
pp. 85-95
Author(s):  
Jevič Petr ◽  
Pražan Radek ◽  
Šedivá Zdeňka
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Single Cylinder ◽  
Diesel Fuels ◽  
Single Cylinder Engine ◽  
Model Diesel ◽  
Fuel Mixtures ◽  
The Individual

The article deals with verification of a diesel fuel and two fuel mixtures blends with different amounts of the bio-component using the model single-cylinder engine without the additional equipment for treatment of exhaust gases. This combustion diesel engine served for measuring the performance characteristics of the model single-cylinder engine and the individual emission components in order to assess the use of these blends of liquid paraffinic diesel fuel in practice and to meet current and forthcoming European legislation and to fulfil the commitments by 2020. A detailed chemical analysis was performed in case of all the tested paraffinic diesel fuels. 

Performance Investigation of a Four Stroke Diesel Engine, Using Water-Based Ferrofluid as an Additive

2011 ◽  
Author(s):  
F. Daneshvar ◽  
N. Jahani ◽  
M. B. Shafii
Keyword(s):  
Experimental Study ◽  
Magnetic Nanoparticles ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Brake Specific Fuel Consumption ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Diesel Fuels ◽  
Water Based

In this experimental study, a four stroke diesel engine was conducted to investigate the effect of adding water-based ferrofluid to diesel fuel on engine performance. To our knowledge, Magnetic nanoparticles had not been used before. To this end, emulsified diesel fuels of 0, 0.4, and 0.8 water-based ferrofluid/Diesel ratios by volume were used as fuel. The ferrofluid used in this study was a handmade water-based ferrofluid prepared by the authors. The results show that adding water-based ferrofluid to diesel fuel has a perceptible effect on engine performance, increasing the brake thermal efficiency relatively up to 12%, and decreasing the brake specific fuel consumption relatively up to 11% as compared to diesel fuel. In addition, the results indicate that increasing ferrofluid concentration will magnify the results. Furthermore, it was found that magnetic nanoparticles can be collected at the engine exhaust using magnetic bar.

scholarly journals Effect of cetane improver addition into diesel fuel: Methanol mixtures on performance and emissions at different injection pressures

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 555-566 ◽  
Author(s):  
Feyyaz Candan ◽  
Murat Ciniviz ◽  
Ilker Ors
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Injection Pressure ◽  
Specific Fuel Consumption ◽  
Exhaust Emission ◽  
Brake Specific Fuel Consumption ◽  
Consumption Values ◽  
Smoke Opacity

In this study, methanol in ratios of 5-10-15% were incorporated into diesel fuel with the aim of reducing harmful exhaust gasses of Diesel engine, di-tertbutyl peroxide as cetane improver in a ratio of 1% was added into mixture fuels in order to reduce negative effects of methanol on engine performance parameters, and isobutanol of a ratio of 1% was used as additive for preventing phase separation of all mixtures. As results of experiments conducted on a single cylinder and direct injection Diesel engine, methanol caused the increase of NOx emission while reducing CO, HC, CO2, and smoke opacity emissions. It also reduced torque and power values, and increased brake specific fuel consumption values. Cetane improver increased torque and power values slightly compared to methanol-mixed fuels, and reduced brake specific fuel consumption values. It also affected exhaust emission values positively, excluding smoke opacity. Increase of injector injection pressure affected performances of methanol-mixed fuels positively. It also increased injection pressure and NOx emissions, while reducing other exhaust emissions.

APPLICATION ON OXYGENATED FUEL OF MONO-ETHER GROUP IN AN IDI DIESEL ENGINE

2012 ◽  
Vol 06 ◽  
pp. 425-430
Author(s):  
HYUNG-GON KIM ◽  
SEUNG-HUN CHOI ◽  
YOUNG-TAIG OH
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Emission Characteristics ◽  
Butyl Ether ◽  
Ether Group ◽  
Oxygenated Fuel ◽  
Effect Of Oxygen ◽  
Gas Recirculation

Effect of oxygen components of fuels on exhaust emissions has been investigated by applying an indirect injection (IDI) diesel engine. This research analyzed variation and/or difference of the engine performance and exhaust emission characteristics of the IDI diesel engine by fueling the commercial diesel fuel and four different mixed ratios of oxygenated blended fuels. Effect of the exhaust gas recirculation (EGR) method was analyzed on the NOx emission characteristics. Ethylene glycol mono-n-butyl ether (EGBE) contains 27% of oxygen components in itself, and it is a kind of effective oxygenated fuel of mono-ether group. Smoke emission from the EGBE was reduced remarkably relative to the commercial diesel fuel. The EGBE can supply oxygen components sufficiently at higher diesel engine loads and speeds. It was found that a simultaneous reduction of the smoke and the NOx was achieved with the oxygenated fuel (10 vol-%) and the cooled EGR method (10%).

ANALYSIS OF OXYGENATED COMPONENT (BUTYL ETHER) AND EGR EFFECT ON A DIESEL ENGINE

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2844-2849 ◽  
Author(s):  
SEUNG-HUN CHOI ◽  
YOUNG-TAIG OH
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Specific Energy Consumption ◽  
Engine Performance ◽  
Nox Emission ◽  
Exhaust Emission ◽  
Engine Fuel ◽  
Butyl Ether ◽  
Significant Difference ◽  
Blended Fuel

Potential possibility of the butyl ether (BE, oxygenates of di-ether group) was analyzed as an additives for a naturally aspirated direct injection diesel engine fuel. Engine performance and exhaust emission characteristics were analyzed by applying the commercial diesel fuel and oxygenates additives blended diesel fuels. Smoke emission decreased approximately 26% by applying the blended fuel (diesel fuel 80 vol-% + BE 20vol-%) at the engine speed of 25,000 rpm and with full engine load compared to the diesel fuel. There was none significant difference between the blended fuel and the diesel fuel on the power, torque, and brake specific energy consumption rate of the diesel engine. But, NOx emission from the blended fuel was higher than the commercial diesel fuel. As a counter plan, the EGR method was employed to reduce the NOx . Simultaneous reduction of the smoke and the NOx emission from the diesel engine was achieved by applying the BE blended fuel and the cooled EGR method.

scholarly journals Evaluation of Diesel Engine Performance and Exhaust Emission Characteristics Using Waste Cooking Oil

2015 ◽  
Vol 773-774 ◽  
pp. 425-429 ◽  
Author(s):  
Nur Atiqah Ramlan ◽  
Abdul Adam Abdullah ◽  
Mohd Herzwan Hamzah ◽  
Nur Fauziah Jaharudin ◽  
Rizalman Mamat
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Engine Speed ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Cooking Oil ◽  
Conventional Diesel Fuel

The depletion of fossil fuels as well as the rises of greenhouse gases had caused most government worldwide to follow the international energy policies for the use of biodiesel. One of the economical sources for biodiesel production is waste cooking oil. The use of waste cooking oil is more sustainable if they can perform similarly to conventional diesel fuel. This paper deals with the experimental study carried out to evaluate the engine performance and exhaust emission of diesel engine operated by biodiesel from waste cooking oil at various engine speed. The biodiesel used are known as B5, which contains of 5% of waste cooking oil and 95% of diesel fuel. The other one is B20, which contains of 20% of waste cooking oil plus 80% of diesel. Diesel was used as a comparison purposes. The results show that power and torque for B5 give the closest trend to diesel. In terms of heat release, diesel still dominates the highest value compared to B5 and B20. For exhaust emission, B5 and B20 showed improvement in the reduction of NOx and PM.

scholarly journals Experimental investigation on cyclic variability, engine performance and exhaust emissions in a diesel engine using alcohol-diesel fuel blends

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 581-589 ◽  
Author(s):  
Samet Gurgen ◽  
Bedir Unver ◽  
İsmail Altin
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Speed ◽  
Load Condition ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Cyclic Variability ◽  
Fuel Blends ◽  
Indicated Mean Effective Pressure ◽  
Cycle Variation

This paper investigates the impacts of using n-butanol-diesel fuel and ethanol-diesel fuel blends on engine performance, exhaust emission, and cycle-by-cycle variation in a Diesel engine. The engine was operated at two different engine speed and full load condition with pure diesel fuel, 5% and 10% (by vol.) ethanol and n-butanol fuel blends. The coefficient of variation of indicated mean effective pressure was used to evaluate the cyclic variability of n-butanol-diesel fuel and ethanol-diesel fuel blends. The results obtained in this study showed that effective efficiency and brake specific fuel consumption generally increased with the use of the n-butanol-diesel fuel or ethanol-diesel fuel blends with respect to that of the neat diesel fuel. The addition of ethanol or n-butanol to diesel fuel caused a decrement in CO and NOx emissions. Also, the results indicated that cycle-by-cycle variation has an increasing trend with the increase of alcohol-diesel blending ratio for all engine speed. An increase in cyclic variability of alcohol-diesel fuel blends at low engine speed is higher than that of high engine speed.

scholarly journals The effect of Diesel-Methanol Blends with Volumetric Proportions on The Performance and Emissions of A Diesel Engine

Mechanika ◽  
2019 ◽  
Vol 25 (5) ◽  
pp. 363-369 ◽  
Author(s):  
ADNAN BERBER
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Gas Temperature ◽  
Engine Torque ◽  
Performance And Emissions ◽  
Maximum Decrease

In this work, the methanol is added to the diesel fuel in the volumetric proportions of 5%-%10-%15 to diminish negative environmental impacts of diesel engines. The diesel-methanol blends in the various proportions are tested in a single-cylinder direct-injection diesel engine. According to the test results, the addition of methanol to the diesel fuel causes a maximum decrease of 13.07 % in the engine torque, and a maximum decrease of 12.54 % in the specific fuel consumption. On the other hand, the exhaust emission results show that the values of CO and CO2 decrease 38.4 % and 5.04%. However, the increase of 3.66% in the exhaust gas temperature causes the increase of 17.1% in the NOx emission. Also, a significant decrease of 39.37% in the smoke opacity is observed compared to that of the diesel fuel. Although the addition of methanol to diesel fuel causes a slightly decrease in the engine performance, the diesel-methanol blends have a reasonable and considerable positive effect on environmental concerns of diesel engines.

Sign in / Sign up

Export Citation Format

Share Document